• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.145-152
• /
• 2016

OBJECTIVES : Visibility at night can be improved by using retroreflection for short distances and phosphorescent line markings for long distances. In this study, we analyzed the characteristics of the phosphorescent line marking through a laboratory luminance test. Field performance analysis was performed through tests conducted on the road. We also examined the luminance measurement methods using the digital image obtained during the phosphorescent visibility evaluation. METHODS : In this study, the laboratory luminance test of the phosphorescent line marking was conducted using seven specimens to characterize the luminance changes according to the type of the glass beads, the thickness of the phosphorescent line marking, and the brightness and irradiation time of the light source. Phosphorescent and general line markings were made at 150 m to investigate the field luminance performance. A preliminary review of the luminance measurement methods was made using a digital image from a digital single-lens reflex (DSLR) camera. The measured luminance ratio of the general and the phosphorescent line markings was compared with the calculated luminance ratio using luminance analysis. RESULTS : Through the laboratory luminance test, it was seen that the change in luminance, which corresponds to the brightness of the light source, appears large but the influence of the thickness and irradiation time is low. The field performance test of the phosphorescent line marking conducted on the road involved measuring the luminance on the day the marking was made and 7 days after the marking was made. The luminance was found to be $190mcd/m^2$ at 30 min after sunset and approximately $10-12mcd/m^2$ 4h after sunset. The results of the luminance test were captured using a digital image for each time group. The luminance ratio of the phosphorescent line marking, when compared to that of the general line marking, showed a similar trend within a 13% maximum error. Additionally, when this luminance ratio is compared to the direct field measurement, it could be confirmed that the luminance ratio, as captured in the digital image, showed a similar tendency. CONCLUSIONS : 1) The change in luminance corresponding to the brightness of the light source is significant in comparison with that corresponding to the thickness and the irradiation time. In addition, the results of the field test for the phosphorescent line marking satisfied the phosphorescent fire protection standard. 2) We examined the validity of the luminance measurement method using a digital image and we concluded that the change in the luminance ratio shows a similar tendency in both the cases. The results can form the basis for luminance measurement methodology for the construction and maintenance of phosphorescent line markings.

• Journal of Korea Foresty Energy
• /
• v.19 no.2
• /
• pp.86-92
• /
• 2000

The liquefactions of $\alpha$-cellulose(Sigma Chemical, C-8002, 47H0383) was prepared in the presence of phenol using sulfuric acid as a catalyst under $N_2$ gas protection at $180^{\circ}C$ for 60minutes to examine its components. The ratio of $\alpha$-cellulose to phenol was 1: 6.2(w/w), and that to sulfuric acid was 1: 0.05(g/$m\ell$). The yields of liquefaction were calculated after the liquefied mixtures were passed through 1G4 glass filter. The luquefied product of $\alpha$-cellulose was analyzed using GC-MS Spectormeter. The 12 compounds identified by GC-MS Spectrometer, of which peak area covers 54% as 2,4-dimethyl phenol, p-isopropyl phenol, 1-ethyl-3,5-dimethyl benzene, o-isopropyl phenol, (E)-2,4\` dihydroxy-stilbene, 2,2\`-methylene-bisphenol, 4,4\`-methylenebisphenol, 3-methyl-2-hydroxyphenyl-(E)-2-hydroxyl-4\`-methoxy-stilbene, 1-phyenyl-1-(4\`hydroxyphenyl)methanol phenol derivatives. From this results, the reaction pathways of the liquefaction of cellulose were proposed through electrophilic substitution reaction. Phenol as a solvent might react with the reaction intermediates as well in the cellulose liquefaction.

• Korean Institute of Interior Design Journal
• /
• v.24 no.1
• /
• pp.178-188
• /
• 2015

This study has the main objective of being of help as a reference data for the application of the finishing materials when designing the interior of the chapel of the church space through analysis of the finishing materials against the chapels of church space which has complex function. As precedent studies for this, the composition of the function and concept of the church space was surveyed and the complex function of the church space was surveyed. The theoretical surveyed was performed according to the casual composition, behavior of the community and role and location of the duties of the church members. The case objects were 10 chapels constructed by 5 professional interior design companies. The content of the analysis was the finishing materials in the chapels and their application characteristics. The detailed considerations to be referred to when designing the interior of the chapels of church space in the future were proposed. The analysis result of the application of the finishing materials according to the locational function of the chapels of church space can be explained as follows. First, the platform area was the characteristic of applying finishing materials which induce visual immersion. As for the floor materials in the platform, in order to minimize the floor sound and vibration phenomenon occurring during movements, noise insulation and dust protection rubber sheet was place and on top of it the floor or the carpet was placed. Second, the Choir area had the difficult problem of having to consider the appropriate sound absorption occurring due to the proliferation of sound and performance of classical instruments at the same time. However, in the case, this problem was solved through the sculptures of convex shape. Third, since the scheelite is a space where many people move around, the finishing material which absorbs sound was mainly used. Fourth, the entrance area was composed of thick wall materials compared to other walls, and the sound absorption character was most significantly considered when applying the finishing material. Fifth, the broadcasting room was composed either in independent type or an open type and performed its function and the main finishing materials was transparent glass which was highest use frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.6
• /
• pp.2118-2123
• /
• 2010

Korean individual occupational exposure control is focused on the retrospective service to the over-exposed person by the reading of personal dosimeter. Since the radiophamaceuticals using in the nuclear medicine department are uncontained radiation sources, the potential exposure at working environment is very high. Moreover, a patient remains radioactive for hours or even days after the administration of a radiopharmaceutical for diagnosis or treatment. Thus, the proper working environmental exposure control must be established and executed to protect not only the affiliated employees, but also guardians accompanying patients and temporarily visiting public from the exposure by the patients. Japanese radiation protection law regulates working environmental radiation exposure by regularly measuring and filing the environmental dose for years. This study was aimed at measuring working environmental radiation dose in the nuclear medicine department of an university hospital located in Daejeon, Korea. We measured the accumulation radiation dose in air at 8 locations in the nuclear medicine department by using the same method as in Japan with glass dosimeters. The highest dose rate, 0.23 mSv per month, was measured at the waiting room, and the second one is at reception desk. Even though the doses were lower than the Korean constraint dose rate (0.3 mSv/week) at the boundary of the radiation controlled area, it was over the dose limit of public (1 mSv/y) and environment (0.25 mSv/y). Conclusionally, it was found that the new or additional procedure was necessary to less the exposure dose to the receptionist and guardians by the environmental radiation dose in the nuclear medicine department.

• Journal of the Korean Society of Costume
• /
• v.6
• /
• pp.121-143
• /
• 1982

Many studies have done on Egyptian Clothing because its unique characteristic culture. However, I was facinated by the exhibitions of Tutankhamen burial treasures which were shown in San Francisco and New York in 1978 and 1979. I found out myself that there are several interesting aspects of clothing to compare 18th dynasty king, Tutankhamun and other dynasties in Egyptian culture. Therefore, I tryed to analized the Egyptian clothing including accessaries with theigr symbols durin 18th dynasty King, Tutankhamun. The most of people were shocked and amazed when they toured the exhibition of Tutankhamun articles which were the most incredible burial treasures in existence today. The body of the King has been embalmed, bandaged and fitted in eight layers of coffins with pure gold mask to represent the god Osiris. Among eight layers of coffins, one is pure solid gold in mummiform, two of mummiforms are made of compact wood covered with sheets of gold and inlaid with multi-colored glass-paste and semi-precious stones. The Egyptian belived that the soul continued to exist throughout eternity if it had passed on examination of its deeds on earth at a "Last Judgement" presided over by Osiris. They also believed that the mummified body could exist in the tomb as a habitation that the soul could revisited. Thus a proper burial was vital for a full existence in the hereafter. They buried dead person in the sealed vault of the tomb with some of the possessions he had used during his life time, such as his furniture, clothing and jewels. In this studies, I've tried to research to various clothings, and accessories with their symbols used during 18th dynasty king, Tutankhamun. The studies are shown as: I) Clothings of Tutankhamun dynasity of Kalasiris, Sheath skirt. Gala skirt, Loin skirt, Hike and Dalmatic. The Dalmatic was first seen in this dynasty. Probably the Roman Christian borrowed the Dalmatica from Egyptian Dalmatic. No where has the same design at the period. II) Egyptian of 18th dynasty Tutankhamun wore big headdress, broad collar necklace passium, pendants, armlets, rings and earrings with very beautiful, exquisite handcraft. They seem the first people who wore earrings in Egyptian history. III) The symbols of decorated items vulture, lotus...Upper Egypt Uraeus, papyrus...Lower Egypt scaravaeus, Nile Riber...rebirth man(Ankh), +...eternal life solar disc, gold...sun ostrich-feather...nobleness God, Horus' eye...protection against enemy IV) Also Egyptian prefered the straight line and a right angle which were the basic principles of architectural arrangement.

• Research in Plant Disease
• /
• v.15 no.1
• /
• pp.23-29
• /
• 2009

Cooking oil and yolk mixture (COY), a environmentally acceptable plant protection agent, and COY+$CaCO_3$+neem oil mixture were studied to control the powdery mildew occurring on eggplant, paprika, cherry tomato and maturity tomato in glass houses and vinyl houses during 2005 to 2007. The morphological changes of the pathogenic fungi on the leaf surface before and after treatment of COY were observed. COY made of rape seed oil and COY+$CaCO_3$+neem oil mixture were sprayed three times with 5 days interval to foliar parts of eggplant, paprika and tomato and the disease development were examined 5 days after final spray. In eggplant, the control efficacy of COY to powdery mildew was 94.6%. In paprika, the control efficacy of COY to powdery mildew was 91.6% and that of COY+$CaCO_3$+neem oil mixture was 96.2% that revealed little higher than COY itself. In tomatoes(cherry or maturity tomato), the control efficacy of COY were about 91 %, however, when COY mixture were sprayed to tomato leaves and stems the powdery mildew was controlled completely. Typical and healthy mycelia, conidiophores and condia were observed through scanning electron microscope in COY unsprayed leaf surface, on the other hand destroyed and winkled mycelia and conidiophores were observed in COY treated leaves regardless host plants nor taxonomic differences of fungi.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2009.06a
• /
• pp.84-85
• /
• 2009

New approaches for detecting, preventing and remedying environmental damage are important for protection of the environment. Procedures must be developed and implemented to reduce the amount of waste produced in chemical processes, to detect the presence and/or concentration of contaminants and decontaminate fouled environments. Contamination can be classified into three general types: airborne, surface and structural. The most dangerous type is airborne contamination, because of the opportunity for inhalation and ingestion. The second most dangerous type is surface contamination. Surface contamination can be transferred to workers by casual contact and if disturbed can easily be made airborne. The decontamination of the surface in the nuclear facilities has been widely studied with particular emphasis on small and large surfaces. The amount of wastes being produced during decommissioning of nuclear facilities is much higher than the total wastes cumulated during operation. And, the process of decommissioning has a strong possibility of personal's exposure and emission to environment of the radioactive contaminants, requiring through monitoring and estimation of radiation and radioactivity. So, it is important to monitor the radioactive contamination level of the nuclear facilities for the determination of the decontamination method, the establishment of the decommissioning planning, and the worker's safety. But it is very difficult to measure the surface contamination of the floor and wall in the highly contaminated facilities. In this study, the poly(styrene-ethyl acrylate) [poly(St-EA)] core-shell composite polymer for measurement of the radioactive contamination was synthesized by the method of emulsion polymerization. The morphology of the poly(St-EA) composite emulsion particle was core-shell structure, with polystyrene (PS)as the core and poly(ethyl acrylate) (PEA) as the shell. Core-shell polymers of styrene (St)/ethyl acrylate (EA) pair were prepared by sequential emulsion polymerization in the presence of sodium dodecyl sulfate (SOS) as an emulsifier using ammonium persulfate (APS) as an initiator. The polymer was made by impregnating organic scintillators, 2,5-diphenyloxazole (PPO) and 1,4-bis[5-phenyl-2-oxazol]benzene (POPOP). Related tests and analysis confirmed the success in synthesis of composite polymer. The products are characterized by IT-IR spectroscopy, TGA that were used, respectively, to show the structure, the thermal stability of the prepared polymer. Two-phase particles with a core-shell structure were obtained in experiments where the estimated glass transition temperature and the morphologies of emulsion particles. Radiation pollution level the detection about under using examined the beta rays. The morphology of the poly(St-EA) composite polymer synthesized by the method of emulsion polymerization was a core-shell structure, as shown in Fig. 1. Core-shell materials consist of a core structural domain covered by a shell domain. Clearly, the entire surface of PS core was covered by PEA. The inner region was a PS core and the outer region was a PEA shell. The particle size distribution showed similar in the range 350-360 nm.

• Journal of Fashion Business
• /
• v.5 no.2
• /
• pp.15-34
• /
• 2001

Ornaments are accessories for the decoration of the body or dress. They aren't unavoidably required one, but serve to make one's dress perfect as decorative industrial art objects. In Morocco, ornaments were initially used as a sign of social position or the class or an incantatory symbol. In effect, they were originally employed to adjust one's dress, not just for decoration, and they were of use for household economy. Gold, silver and handcraft available for exchange were a means of increasing one's property and an indication of social standing and wealth. In particular, the dress and jewelry of a bride was a measure of her family's wealth, regarded as a symbol of her chastity and value. The ornaments symbolically back up people's faith in supernatural power, and their real value is based on implicit form or way of decoration, not the external shape. Specifically, there is a tendency to use the form of animal as a protector, not one to frighten people. In the artistic tradition of Morocco, fish pattern stands for water and rain, and eagle and bird are considered to be related to fate. Scorpion and lizard are depicted as an inquirer of sun, and snake is a symbol of abundance and sexual instinct, being viewed to have an ability to cure disease. Turtle pattern is a symbol of saint because it protects one from the evil. The ornaments are made of gold, silver, amber, clam, garnet, glass, nielle, enamel, glaze, coral or tree, and symbolic patterns are used, including hand(a symbol of five numerals), turtle, lizard, scorpion, eye, triangle, bird and eggs. They are very big and diverse, being categorized into ornaments for the head or the chest, neckless, fibula, earring, bracelet and ring. For Moroccans, make-up is a sort of instinctive behavior to meet aesthetic and sexual desire. They also wear make-up for practical purpose of protection, intentionally inflict a wound on the skin for ceremonial or religious purpose, paint the skin with pigment, or have the part of the body tattooed for incantatory purpose. All this actions are regarded as make-up. The raw material of cosmetics is aker, a vegetable dye. They get the lips or cheeks turn red and paint eyebrows with yellow saffran powder to have a bad devil lose its strength. Tattooing is mainly done by women and viewed as a sign of their value or social organization they belong to. Sometimes that is used to represent a woman's being old enough to marry or getting married already or the frequency of marriage. Besides, tattoo is believed to prevent or remedy loose bowels or cough, depending on its location or pattern, and they often change tattoo according to the change of beauty art.

• Korean Journal of Health Education and Promotion
• /
• v.19 no.2
• /
• pp.57-72
• /
• 2002

Students spend most of their time in school. Schools have the possibility of unanticipated accidents, however, and the rate of accidents in schools is increasing. The purpose of this study were to understand the accidents that arise in schools as well as the school safety management system and by analyzing affects that school safety management system has on accidents in schools, to come lip with a preventive plan. 906 high school sophomore students attending in Seoul were surveyed 1Tom November 12th to 23rd 2001. The results were following: 1. Students surveyed comprised of the following: Male 48.9%, Female 51.1% Public Schools 32.6%, Private Schools 67.4% Boys Schools 48.9%, Girls Schools 51.1% 2. In the past year, male students had more accidents(p〈.05) in school. 3. In examining students safety management control, 94.0% said that, there is an infirmary, there is a clear distinction between the playing fields and pathways(74.8%), and the chemicals in the labs are kept in a safe manner(77.2%). The above items were generally well maintained. However, the following recorded low scores. There are warning signs in hazardous places and facilities(30.5%), There is guiding principle to examine the safeness on a regular basis(24.9%), and There are slogans and posters preventing accidents(40.3%). 4. In examining the facilities of the schools that were surveyed, the majority answered, yes to the following. There are hazardous facilities or materials at school(62.9%), There are sharp edges in educational supplies and equipment(59.8%), There are nails or other components that are sticking out of desks and chairs(75.9%), There are slippery spots in the corridors and classrooms(69.3%), There are stones, scrap metal, broken glass, and trash on the playing fields(66.6%). Furthermore, the students surveyed said, yes to the following although in low percentages. The amount of sand on the playing fields is sufficient(49.1%), The soccer and basket goal posts are fastened (53.7%), There are safety bars on the windows of classrooms and corridors (27.4%), There are safety mats on the entrance to restrooms preventing slips (14.2%), The stairs have slip protection measures(49.1%). 5. In analyzing the affect that the school safety management system has on accidents in school, schools that had slogans and posters preventing accidents had a 50% less chance of accidents(p〈.05), schools with chemicals and equipment in the labs that were safely maintained had an 80% less probability of accidents(p〈.0l), and the schools that had sharp edges in the educational supplies and equipment had an 80% greater chance of accidents(p〈.01).

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1638-1643
• /
• 2018

Multi-layer ceramic capacitors as decoupling capacitor were fabricated by dielectric composition with a high dielectric constant. The fabricated decoupling capacitors were embedded in the PCB of the 10G RF transceiver module and evaluated for the characteristics of electrical noise by the level of AC input voltage. In order to further improve the electrical properties of the $BaTiO_3$ based composite, glass frit, MgO, $Y_2O_3$, $Mn_3O$, $V_2O_5$, $BaCO_3$, $SiO_2$, and $Al_2O_3$ were used as additives. The electrical properties of the composites were determined by various amounts of additives and optimum sintering temperature. As a result of the optimized composite, it was possible to obtain a density of $5.77g/cm^3$, a dielectric constant of 1994, and an insulation resistance of $2.91{\times}10^{12}{\Omega}$ at an additive content of 5wt% and a sintering temperature of $1250^{\circ}C$. After forming a $2.5{\mu}m$ green sheet using the doctor blade method, a total of 77 layers were laminated and sintered at $1180^{\circ}C$. A decoupling capacitor with a size of $0.6mm(W){\times}0.3mm(L){\times}0.3mm(T)$ (width, length and thickness, respectively) and a capacitance of 100 nF was embedded using a PCB process for the 10G RF Transceiver modules. In the range of AC input voltage 400mmV @ 500kHz to 2200mV @ 900kHz, the embedded 10G RF Transceiver modules evaluated that it has better electrical performance than the non-embedded modules.