• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.24-32
• /
• 2023

This paper studied HART II in descending flight using rotorcraft analysis code based on geometrically exact beam (GEB) model. The present GEB model expressed by a mixed variational formulation could capture the geometrically nonlinear behavior of the blade without arbitrary assumptions. In previous results, correlation of airloads with structural moments for HART II was not as good as blade deflections. However, in present results, predictions of airloads and structural loads are fairly correlated with measured data.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.194-202
• /
• 2014

Steering axis of suspensions is an important factor that affects ride and handling quality in the vehicle chassis development. Macpherson strut and double wishbone's steering axis are defined geometrically, but multi-link suspensions can not be geometrically analyzed. In this case instant axis theory is commonly used to find a steering axis. Since the steering axis is moving with varying caster and kingpin inclination angle, this method approximately corresponds with exact solution. In this paper, we propose a velocity analysis method to find a pure rotational axis of the wheel relative to suspension arms, that is exact solution of the steering axis. This paper extends the method to analyze the steering axis of multi-link suspensions with bushing compliance. The analysis results applied to double wishbone and multi-link suspensions demonstrate validity and accuracy of the proposed method.

• Coupled systems mechanics
• /
• v.11 no.6
• /
• pp.525-542
• /
• 2022

In this work we present an advanced approach to the design of small wind turbine support steel structures. To this end we use an improved version of previously developed geometrically exact beam models. Namely, three different geometrically exact beam models are used, the first two are the Reissner and the Kirchhoff beam models implementing bi-linear hardening response and the third is the Reissner beam capable of also representing connections response. All models were validated in our previous research for a static response, and in this work they are extended to dynamic response. With these advanced models, we can perform analysis of four practical solutions for the installation of small wind turbines in new or existing buildings including effects of elastoplastic response to vibration problems. The numerical simulations confirm the robustness of numerical models in analyzing vibration problems and the crucial effects of elastoplastic response in avoiding resonance phenomena.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.105-112
• /
• 2007

The linkage framework of geometric modeling based on NURBS(Non-Uniform Rational B-Spline) surface and shell finite analysis is developed in the present study. For this purpose, geometrically exact shell finite element is implemented. NURBS technology is employed to obtain the exact geometric quantities for the analysis. Especially, because NURBS is the most powerful and wide-spread method to represent general surfaces in the field of computer graphics and CAD(Computer Aided Design) industry, the direct computation of surface geometric quantities from the NURBS surface equation without approximation shows great potential for the integration between geometrically exact shell finite element and geometric modeling in the CAD systems. Some numerical examples are given to verify the performance and accuracy of the developed linkage framework. In additions, trimmed surfaces with some cutouts are considered for more practical applications.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.794-801
• /
• 2006

The linkage framework of geometric modeling and analysis based on the NURBS technology is developed in this study. The NURBS surfaces are generated by interpolating the given set of data points or by extracting the necessary information to construct the NURBS surface from the IGES format file which is generated by the commercial CAD systems in the present study. Numerical examples shows the rate of displacement convergence according to the paramterization methods of the NURBS surface. NURBS can generate quadric surfaces in an exact manner. It is the one of the advantages of the NURBS. A trimmed NURBS surface that is often encountered in the modeling process of the CAD systems is also presented in the present study. The performance of the developed geometrically exact shell element integrated with the exact geometric representations by the NURBS equation is compared to those of the previous reported FE shell elements in the selected benchmark problems.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.4
• /
• pp.183-190
• /
• 2018

This paper presents optimization of the main spar of Human-Powered Aircraft (HPA) wing. Mass minimization was attempted, while considering large torsional deformation of the beam. Sequential Quadratic Programming (SQP) method was adopted as a relevant tool to conduct structural optimization algorithm. An inner diameter and ply thicknesses of the main spar were selected as the design variables. The objective function includes factors such as mass minimization, constant tip bending displacement, and constant tip twist of the beam. For estimation of bending and torsional deformation, the geometrically exact beam model, which is appropriate for large deflection, was adopted. Properties of the cross sectional area which the geometrically exact beam model requires were obtained by Variational Asymptotic Beam Sectional Analysis (VABS), which is a cross sectional analysis program. As a result, maintaining tip bending displacement and tip twist within 1.45%, optimal design that accomplished 7.88% of the mass reduction was acquired. By the stress and strain recovery, structural integrity of the optimal design and validity of the present optimization procedure were authenticated.

• Structural Engineering and Mechanics
• /
• v.22 no.3
• /
• pp.263-278
• /
• 2006

Starting with the geometrically non-linear formulation and the subsequent linearization, this paper presents a consistent formulation of the exact mechanical analysis of geometrically and materially linear three-layer continuous planar beams. Each layer of the beam is described by the geometrically linear beam theory. Constitutive laws of layer materials and relationships between interlayer slips and shear stresses at the interface are assumed to be linear elastic. The formulation is first applied in the analysis of a three-layer simply supported beam. The results are compared to those of Goodman and Popov (1968) and to those obtained from the formulation of the European code for timber structures, Eurocode 5 (1993). Comparisons show that the present and the Goodman and Popov (1968) results agree completely, while the Eurocode 5 (1993) results differ to a certain degree. Next, the analytical solution is used in formulating a general procedure for the analysis of layered continuous beams. The applications show the qualitative and quantitative effects of the layer and the interlayer slip stiffnesses on internal forces, stresses and deflections of composite continuous beams.

• The KIPS Transactions:PartA
• /
• v.10A no.2
• /
• pp.157-164
• /
• 2003

Volume graphics have received a lot of attention as a medical image analysis tool nowadays. In the visualization based on volume graphics, there is a process called voxelization which transforms the geometrically defined objects into the volumetric objects. It enables us to volume render the geometrically defined data with sampling data. This paper suggests a voxeliration method using the cutting surfaces of cubes, implements the method on a PC, and evaluates it with simple geometric modeling data to explore propriety of the method. This method features the ability of calculating the exact normal vector from a voxel, having no hole among voxels, having multi-resolution representation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.5
• /
• pp.287-292
• /
• 2021

We utilized the isogeometric analysis (IGA) method that uses NURBS basis functions in CAD systems, to account for the geometric exactness of a geometrically exact beam deformation, on a new type of metamaterial, twist-translation coupled structure showing a large twist angle. A two-dimensional unit cell structure was embedded in a cylindrical wall, using free-form deformation and an appropriate interpolation scheme. A parametric study on the effects of the dimensions of the cylinder and the number of cells, on the twisting angle was performed. Furthermore, the mechanism of the twist-translation coupled metamaterial was explored through numerical examples.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.2
• /
• pp.71-78
• /
• 2018

This paper presents the assembling of multiple patches based on the single patch isogeometric formulation for the shear deformable shell element given in the previous study. The geometrically exact shell formulation has been accomplished with the shell theory based formulation and the generalized curvilinear coordinate system directly derived from the given NURBS geometry. For the knot elements matching across adjacent surfaces, the zero-th and first parametric continuity conditions are considered and the corresponding coupling constraints are implemented by a master-slave formulation between adjacent patches. The constraints are then enforced by a substitution method for condensation of the slave variables, thereby reducing the model size. Through numerical investigations, the important features of the first parametric continuity condition are confirmed. The performance of the multi-patch shell models is also examined comparing the rate of convergence of response coefficients for the zero and first order continuity conditions and continuity in coupling boundary between two patches is confirmed.