• 천문학회보
• /
• 제38권2호
• /
• pp.89.2-89.2
• /
• 2013

Solar energetic transients, e.g., flares, CMEs, etc., release large amount of energy which is expected to excite acoustic waves (p-modes) by exerting mechanical impulse of the thermal expansion of the flare on the photosphere. We study the p-mode properties of flaring and dormant active regions (ARs) to find association between flare and p-mode parameters. We compute the magnetic and flare activity indices of ARs using the line-of-sight magnetograms and GOES X-ray fluxes, respectively. The p-mode parameters are computed from the ring-diagram analysis. We correct p-mode parameters for magnetic field, filling factors and foreshortening by multiple linear-regression analysis. Our analysis of several flaring and dormant ARs observed during the Carrington rotations 1980-2109, showed strong association of mode parameters with magnetic and flare activities. We find that the mode parameters are contaminated by the geometrical effect. Mode amplitude decreases with angular distance from the solar disc centre. The mode width increases with magnetic activity while amplitude showed opposite relation due to mode absorption by the sunspot. After correcting modes due to all geometrical effects, magnetic activity and filling factor, we find that the modes amplitude, and mode energy increases with flare energy while width shows opposite relation.

• 한국의류학회지
• /
• 제22권1호
• /
• pp.72-79
• /
• 1998

Journal of the Korean Society of Clothing and Textiles Vol. 22, No. 1 (1998) p. 72∼79 The purpose of this study was to investigate the effects of geometrical structure and fiber type on the water vapor transport properties of nonwoven batting materials. Two types of fiber were used such as polyester and wool. Correlation between physical properties of nonwovens and water vapor transport rate was analyzed by Pearson Correlation. Steady and dynamic state water vapor transport properties were measured by absorption, evaporation and cobaltots chloride method respectively. The results were as follows: 1) In geometrical structure, thickness of nonwovens was effected on absorption and evaporation rate and air permeability was more influencing factor on water vapor transport rate than porosity. There were no decreasing of water vapor transport rate in hydrophilic fiber at high relative humudity. 2) The hydrophilicity of fiber affected steady and dynamic state water vapor permeabilities and wool nonwoven showed higher water vapor transport rate than polyester at high relative humidity. 3) Thickness showed higher correlation coefficient with water vapor transport rate than other physical properties of nonwovens.

• International Journal of Precision Engineering and Manufacturing
• /
• 제1권1호
• /
• pp.62-70
• /
• 2000

The design of gear train is a kind of mixed problems which have to determine various types of design variables; i,e., continuous, discrete, and integer variables. Therefore, the most common practice of optimum design using the derivative of objective function has difficulty in solving those kinds of problems and the optimum solution also depends on initial guess because there are many sophisticated constrains. In this study, the Genetic Algorithm is introduced for the optimum design of gear trains to solve such problems and we propose a genetic algorithm based gear design system. This system is applied for the geometrical volume(size) minimization problem of the two-stage gear train and the simple planetary gear train to show that genetic algorithm is better than the conventional algorithm solving the problems that have continuous, discrete, and integer variables. In this system, each design factor such as strength, durability, interference, contact ratio, etc. is considered on the basis of AGMA standards to satisfy the required design specification and the performance with minimizing the geometrical volume(size) of gear trains

• 산업공학
• /
• 제18권3호
• /
• pp.247-252
• /
• 2005

In the automated production environment in the present days, the minimization of manual operation becomes a very important factor in increasing the efficiency of the production system. The exit burr produced through the milling operation on the edge of workpiece usually requires manual deburring process to enhance the level of precision of the resulting product. So far, researchers have developed various methods to understand the formation of exit burr in cutting process. One method to analytically identify the formation of exit burr was to use the geometrical information of CAD and CAM data used in automated machining. This method, in turn, generated the information resulting from the analysis such as burr type, cutting region, and exit angle. Up to now, the geometrical data were restricted to the single feature and single path. In this paper, a method to deal with the complicated geometric features such as line segment, arc, hole, and spline will be presented and validated using the field data. This method also deals with the complex workpiece shape which is a combination of multiple features. As for the cutting path, multiple tool path is analyzed in order to simulate the real cutting process. All this analysis is combined into a Windows based software and real data are used to validate the program in the conclusion.

• 한국CDE학회논문집
• /
• 제18권5호
• /
• pp.367-373
• /
• 2013

In this study, the penetration characteristic from the cubic and cylindrical penetrator consisting of tungsten material with the velocity of 2,300 m/s is evaluated and the penetration possibility into the target is confirmed. The design of shape and size of penetrator is directly related to space and weight of the warhead. AUTODYN-3D simulation is used to study the penetration effect of penetrator. The purpose of numerical analysis is to verify the penetration characteristic with various L/D penetrator. The penetration performance of penetrator with identical weight due to the shape is also confirmed. The cylindrical and cubic penetrator has enough penetration energy on constant target body. Because the possibility of 2'nd penetration is important factor after 1'st penetration into target body, residual velocity of residual mass must be existed as much as possible. As geometrical shape ratio increases, penetration performance is confirmed to improve.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.473-473
• /
• 2009

There have been many academic researches on the aerodynamic design of wind turbine based on blade element method (BEM) and momentum theory (MT, or actuating disk theory). However, in the real world, the turbine blade design requires many additional constraints more than theoretical analysis. The standard procedure is studied in the present paper to design new blades for the wind turbine system ranged from the small size from 1 to 10 kW. From the experience of full design of a 10 kW blade, the authors tried to set up a standard procedure for the aerodynamic design based on IEC 61400-2. Wind-turbine scale, rotating speed, and geometrical chord/twist distribution at the segmented span positions are calculated with a suitable BEM/MT code, and the geometrical shape of tip and root should be modified after considering various parameters: wing-tip vortex, aerodynamic noise, turbine efficiency, structural safety, convenience of fabrication, and even economic factor likes price, etc. The evaluated data is passed to the next procedure of structural design, but some of them should still be corresponded with each other: the fluid-structure interaction is one of those problems not yet solved, for example. Consequently, the design procedure of small wind-turbine blades is set up for the mass production of commercial products in this research.

• 대한수학교육학회지:학교수학
• /
• 제10권2호
• /
• pp.181-197
• /
• 2008

Bertrand's Paradox는 '임의의 현(random chord)'의 의미가 분명하지 않기 때문에 구하는 방법에 따라 그 결과가 다르게 나오는 paradox(역설)로 알려져 있다. 본 논문에서는 현의 임의성에 대한 구체적인 제시의 부재로 인해 발생하는 다양한 풀이 방법에 대해 분석하였다. 또한 세 가지 풀이의 수학적 계산과 현실 세계에서의 물리적 실험의 결과에서 발생하는 차이를 알아보고, '임의의 현'의 실제적인 의미에 대한 공리적인 정의를 통하여 보편 타당한 답을 구하고자 하였다. 이를 구하는 과정에서 적분기하학의 기본개념인 측도와 적분과 연관이 있는 기하학적 확률지도가 Laplace의 고전적 관점을 기본으로 하는 현 교육과정에 적합한 요소인가에 대한 반성과 그의 위상에 관해 논하였다.

• Steel and Composite Structures
• /
• 제39권4호
• /
• pp.453-469
• /
• 2021

The cracking at the transverse diaphragm cutout is one of the most severe fatigue failures threatening orthotropic steel decks (OSDs), whose mechanisms and crack treatment techniques have not been fully studied. In this paper, full-scale experiments were first performed to investigate the fatigue performance of polished cutouts involving the effect of an artificial geometrical defect. Following this, comparative experimental testing for defective cutouts strengthened with carbon fiber-reinforced polymer (CFRP) was carried out. Numerical finite element analysis was also performed to verify and explain the experimental observations. Results show that the combinative effect of the wheel load and thermal residual stress constitutes the external driving force for the fatigue cracking of the cutout. Initial geometrical defects are confirmed as a critical factor affecting the fatigue cracking. The principal stress 6 mm away from the free edge of the cutout can be adopted as the nominal stress of the cutout during fatigue evaluation, and the fatigue resistance of polished cutouts is higher than Grade A in AASHTO specification. The bonded CFRP system is highly effective in extending the fatigue life of the defective cutouts. The present study provides some new insights into the fatigue evaluation and repair of OSDs.

• The Journal of Korean Physical Therapy
• /
• 제22권6호
• /
• pp.59-63
• /
• 2010

Purpose: Driving a car is an essential component of daily life. For safe driving, each driver must perceive sensory information and respond rapidly and accurately. Brake response time (BRT) is a particularly important factor in the total stopping distance of a vehicle, and therefore is an important factor in traffic accident prevention research. The purpose of the current study was (1) to compare accelerometer. BRTs analyzed by three different methods and (2) to investigate possible correlations between accelerometer-BRTs and foot switch-BRTs, which are measured method using a foot switch. Methods: Eighteen healthy subjects participated in this study. BRT was measured with either a tri-axial accelerometer or a footswitch. BRT with a tri-axial accelerometer was analyzed using three methods: maximum acceleration time, geometrical center, and center of maximum and minimum acceleration values. Results: Both foot switch-BRTs and accelerometer-BRTs were delayed. ANOVA for accelerometer BRTs yielded significant main effects for axis and analysis, while the interaction effect between axis and analysis was not significant. Calculating the Pearson correlation between accelerometer-BRT and foot switch-BRT, we found that maximum acceleration time and center of maximum and minimum acceleration values were significantly correlated with foot switch-BRT (p<0.05). The X axis of the geometrical center was significantly correlated with foot switch-BRTs (p<0.05), but Y and Z axes were not (p>0.05). Conclusion: These findings suggest that the maximum acceleration time and the center of maximum and minimum acceleration value are significantly correlated with foot switch-BRTs.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권3호
• /
• pp.131-140
• /
• 2004

본 연구의 목적은 재료 및 기하학적 비선형을 고려한 개선된 소성힌지 해석을 이용한 평면 강골조 시스템의 최적설계알고리즘 개발이다. 개발된 알고리즘을 이용하여 기둥의 유효길이계수(K-factor) 산정없이 골조의 최적설계를 수행하였다. 본 연구에서 2개의 파리미터를 이용한 다단계 이산화 최적화기법이 개발되어 적용되었다. 목적함수는 구조물의 중량을, 제약조건은 임계하중, 사용성, 유연성등이 고려되었다. 예제를 통해 개발된 프로그램의 효율성, 적용성, 유용성등을 보였다.