• Geomechanics and Engineering
• /
• v.8 no.6
• /
• pp.757-767
• /
• 2015

Rock mass is an important engineering material. In hydropower engineering, rock mass of bank slope controlled the stability of an arch dam. However, mechanical characteristics of the rock mass are not only affected by lithology, but also joints. On the basis of field geological survey, this paper built rock mass material containing parallel concentrated joints with different dip angle, different number under different stress conditions by PFC (Particle Flow Code) numerical simulation. Next, we analyzed mechanical property and fracture features of this rock mass. The following achievements have been obtained through this research. (1) When dip angle of joints is $15^{\circ}$ and $30^{\circ}$, with the increase of joints number, peak strength of rock mass has not changed much. But when dip angle increase to $45^{\circ}$, especially increase to $60^{\circ}$ and $75^{\circ}$, peak strength of rock mass decreased obviously with the increase of joints number. (2) With the increase of confining stress, peak strengths of all rock mass have different degree of improvement, especially the rock mass with dip angle of $75^{\circ}$. (3) Under the condition of no confining stress, dip angle of joints is low and joint number is small, existence of joints has little influence on fracture mode of rock mass, but when joints number increase to 5, tensile deformation firstly happened at joints zone and further resulted in tension fracture of the whole rock mass. When dip angle of joints increases to $45^{\circ}$, fracture presented as shear along joints, and with increase of joints number, strength of rock mass is weakened caused by shear-tension fracture zone along joints. When dip angle of joints increases to $60^{\circ}$ and $75^{\circ}$, deformation and fracture model presented as tension fracture zone along concentrated joints. (4) Influence of increase of confining stress on fracture modes is to weaken joints' control function and to reduce the width of fracture zone. Furthermore, increase of confining stress translated deformation mode from tension to shear.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.277-281
• /
• 2007

Quite a while ago, Organizations which have slope DB system was running slope of management in several. Frequently, Slope failure was happened by abnormal weather and limit of valuation system at the managed slope. Analysis of other organization slope DB systems is very important that slope DB system maintains same regions on geology. In Korea, slope DB system was running at KEC(Korea Expressway Corporation), Korail(Korea Railroad), and KIGAM(Korea Institute of Geoscience and Mineral Resources). We research theirs DB constructing. For reviewed slope DB system of other country, we searched NLIC(Natural Landslide Information Center)'s DB system in U.S.A., GEO's LPM(landslide Prevention Measures) program in Hongkong, DPRI' ILC(International Consortium on Landslides) program in Japan, and AGSO(Australian Geological Survey Organization)'s NGVUC program in Australia.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.129-144
• /
• 2003

Generally, investigation methods of cut slope are conducted only geological surface survey to gain engineering geological data of cut slopes. These methods have many problems such as limitations of investigation for a special area. So geophysical investigations such as geotomography, seismic and electrical resistivity methods have been used to search for failure surface in potential failure slopes or failed slopes. But investigation method using the borehole camera is recently a used method and it is thought that this method is more reliable method than other investigation methods because of being able to see by the eyes. Therefore, this paper was conducted investigations of borings and BIPS(Borehole Image Processing System) to search for potential sliding surfaces and was applied to obtain information of discontinuity on failed and potential failure slope in highway. As the results of BIPS, we could decide potential sliding surface in the slope, conducted to check slope stability and decided slope stability measures.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.201-208
• /
• 1999

The NATM(New Austrian Tunnelling Method) has been used for tunnelling since 1980's. But Collapses of tunnel under construction take place frequently, especially at urban areas because of adjacent buildings, underground conduits and traffic loads. This paper is a case study on the reinforcement method of subway tunnel at urban areas. In this study, ground inspection, geological investigation, laboratory test and numerical analysis by means of FDM program were carried out. The tunnel excavation was stopped because of over excessive brake of tunnel crown and shotcrete was installed to prevent deformation of adjacent ground as the temporary method. From the result of field survey and geological investigation, it is found that the soft weathered soil was distributed to the ground of tunnel invert unlike original investigation. The results of the analysis and the study show that the SGR(Space Grouting Rocket) method and Umbrella method can be applied for the stability of tunnel excavation and in addition the reinforcement of concrete lining is required for long-term stability of tunnel.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.72-77
• /
• 2003

The study tasked by Ryan Lode Mines, Inc. involved analysis of pit slope stability for two future pits, Ryan and Curlew. A geological discontinuity survey and groundwater information were obtained through a field program. Twenty core logs containing geotechnical information were used for rock mass classification. The kinematic analysis was performed based on a friction angle (${\Phi}=35^{\circ}$), the distribution of geological structures, and a dry slope condition. Factors of safety of pit slopes in two future mines were determined using the limit equilibrium method. The mine slopes and benches designed by Mine Development Associates (MDA) were analyzed. The analysis indicated that both pits should have an overall safety factor above 1.0, provided the slopes are kept dry. However, slopes in both pits exceeding 91.4 m (300 ft) high will become critical, when water fills the cracks and discontinuities.

• The Journal of Engineering Geology
• /
• v.11 no.2
• /
• pp.131-139
• /
• 2001

Until recently, limestone yield production is mainly depend on geological investigation and boring. In the study seismic and electrical method are applied to calculate the basic data of limestone yield production. the result of geophysical prospecting, the depth of bed rock is approximately 17m. And there is a slightly difference between the limestone layer boundary which is drawn by electrical prospecting method and that of geological investigation.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.254-256
• /
• 2003

A total of one hundred and twenty three goldbearing mineral deposits in the Charters Towers area west of Townswille, Queensland, Australia were initially classified into four named and unnamed separate vein styles, with different trends and alteration patterns, a breccia-style deposit and placer gold deposits. The area has vein deposits in Ordovician and Silurian granitoids and breccia-style in the Carboniferous volcanics. In this paper a modeling of these deposits is described using geological mapping, landscape analysis and digital imagery (Landsat TM and geophysics) to improve the classification and identification of possible new target for exploration.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.399-406
• /
• 1999

Recently, the construction of the several highway bridges in the karst area have encountered severe problems associated with cavities and sinkholes. To solve this problems, it is important to understand the distribution characteristics of cavities in the construction site on limestone area. This paper briefly describes the different types, the distribution control factors and the infill sediment types of lime-cavities in the study area, bridge site in the karst area and propose the effective method of survey design. Cavity system may be divided into two main groups, 1)'slot and cave system'and 2)'sinkhole and cave system'. And the shape, the size and the distribution pattern of cavity are controlled by three main factors - rock type, geological structure and ground water condition. Additionally, infill sediment may be considered as one of the important design factors for foundation design and divided into four types by sediment properties. There are geophysical thechnics and geologic survey and drilling test, etc. by the survey method to interpretate characteristics of cavity system, and this methods are optimally designed at the site investigation stage.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2009.05a
• /
• pp.73-87
• /
• 2009

Geophysical survey for unconformity-type uranium deposit applied to this study area in Athabaska Basin, Canada were carried out airborne TEM and magnetic, resistivity-induced polarization (DC-IP), puser seismic reflection and well-logging method. The results of airborne survey interpreted the lithological boundary, geological structures, and conductors. Also, these results decided to main targets for ground DC-IP survey. The Low resistivity and the high chargeability slices of 3D modeling interpreted from DC-IP survey response for conductors related to hydrothermal alteration zones and fault-controlled graphitic zones occurring at the unconformity-type uranium deposit, and they confirmed by diamond drilling. Seismic results interpreted to lake bottom surface, alluvium layer and intra-sandstone faults. We suggest the resonable field data acquisition of DC-IP method on the land or the lake in Athabaska Basin.

• 한국지구물리탐사학회:학술대회논문집
• /
• 1999.08a
• /
• pp.117-136
• /
• 1999

The geophysical survey at pre-investigation stage can hardly provide the detailed information on geological structure of site which has difficulty in access and thick overburden. The TSP (VSP applied in tunnel) survey at post-investigation stage can show the detailed geology ahead of tunnel and around cavern. The TSP survey was carried out at the Pyongtaek LPG storage cavern site during the cavern excavation and provided the location and orientation of the fault inferred below Namyangho. In order to confirm the result of TSP survey four boreholes were drilled in access tunnel. The fault was also detected by borehole survey and the location was coincided with the result of TSP survey. Depend on the result of TSP survey and core logging, the design such as cavern layout and length could have been changed. As another case history the TSP survey was performed at the Mumeuje road tunnel which has poor geological information due to thick overburden. The support design was also changed on the base of TSP survey.