• 대한조선학회논문집
• /
• 제55권4호
• /
• pp.306-312
• /
• 2018

To navigate in ice-covered waters, the ice-breaking process is required. The ice-breaking mode depends on material properties of sea ice and ice conditions. The ice-breaking mode is classified into ramming and continuous ice-breaking. The ramming is effective on large ice features, such as thick ice ridge and icebergs, and the continuous ice-breaking is on level ice. In general, the impact time duration of crushing or bending on ice sheets is from 0.2 to 1.0 second. However, impact duration in ramming will be increased. The Korean ice-breaking research vessel ARAON conducted her research voyage in the Antarctic sea during the winter of 2012. The IBRV ARAON measured strain in ramming and continuous ice-breaking. Strain gauge signals were recorded during the planned ice-breaking performance and the unplanned ice transits in heavy ice conditions. The aim of this study is to investigate the ice load signals measured in ramming processes under the heavy ice condition. Based on the time history of the signals, a raising time, a half-decaying time and time duration were investigated and compared with the previous study which was suggested the five profiles of the ice load signals.

• 한국기계가공학회지
• /
• 제19권9호
• /
• pp.100-106
• /
• 2020

This study analyzes the residual stress of AISI 1536V for an engine shaft of the shipbuilding industry and AISI A387 for a reactor shell of the chemical refining industry by the hole drilling method with a strain gauge rosette, which transforms fine mechanical changes into electrical signals. Tensile residual stress is generated in the forging and heat treatment process because specimens are affected by thermal stress and metal transformation stress. In the heat treatment process, the residual stress of AISI A387 is almost 170% the yield strength at 402 MPa. Since during the machining process, variable physical loads are applied to the material, compressive residual stress is generated. Under the same condition, the mechanical properties greatly affect the residual stress during the machining process. After the stress-relieving heat treatment process, the residual stress of AISI A387 is reduced below the yield strength at 182 MPa. Therefore, it is necessary to control the temperature, avoid rapid heat change, and select machining conditions depending on the mechanical properties of materials during manufacturing processes. In addition, to sufficiently reduce the residual stress, it is necessary to study the optimum condition of the stress-relieving heat treatment process for each material.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권3호
• /
• pp.233-239
• /
• 2014

엔진성능 분석을 위해서는 기관의 정확한 출력이 기본적으로 중요한 인자이며, 또한 오늘날 내연기관에서 연소압력 분석 장치는 엔진의 연구와 개발, 환경규제 및 엔진의 유지관리를 위해서 필수 장비로 대두 되고 있다. 엔진의 출력뿐만 아니라 연소상태를 분석하여 엔진의 상태에 대한 올바른 판단을 유도하고, 구체적인 개선방법을 제시하여 실질적으로 연료소비량을 절감하여, 엔진의 유지관리 및 운항비 절감에 도움이 되도록 하기위해서는 이를 위한 도구가 절실히 필요하다. 따라서 본 연구는 개발된 측정 장치를 이용하여 선박용 발전기관인 실험엔진의 연소분석을 행하였으며, 실험기관의 불규칙적인 연소상태를 체크하고 재조정하여 안정된 운전 상태를 유지할 수 있었음은 물론 연료절감에 기여할 수 있었다. 이상의 결과로 엔진출력을 정확하게 측정할 수 있는 새로운 방법에 의한 측정 장치가 개발되었으며, 그 유용성이 입증되었다고 판단된다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2173-2178
• /
• 2008

Railroad is the major factor of vibration source in railway vehicles, and it must carefully maintained the original condition to secure the safety and good ride comfort of passenger. Measuring the condition of rail irregularities such as surface, alignment, gauge, twist and cant etc is required to maintain the good performance of railroad. Currently, the various rail irregularity measurement systems(EM120, ROGER1000K and the Total Rail Irregularity Measurement system of Korea High Speed Train) are operated in Korea to estimate the rail irregularity. It is hard to verify the correlation of one rail irregularity data of a measurement system with the other, because they have been adopted different rail irregularity estimation methods. The best method securing the reliability of the irregularity data is the direct confirmation on the ground where the measurement system had detected as a fault section, but it is impossible to apply all sections simultaneously due to limitation of time, labor, cost and equipments. There is a method to secure the reliability of the data by using acceleration values. Rail irregularities, the major factor of vibration in railway vehicle, are transmitted to the vehicle acceleration through masses, springs, dampers and joints as the system dynamic formation. In this study, Transition Function has been adopted by using the rail irregularity and the acceleration value regarding as input & output parameters respectively. It has been verified by comparing the analyzed results with real measured irregularity data from the Total Rail Irregularity Measurement system of Korea High Speed Train. Also various methods has been accomplished to verify the correlation between rail irregularities and acceleration values.

• 수산해양기술연구
• /
• 제50권3호
• /
• pp.233-243
• /
• 2014

The difference of mooring tension by type of buoy was investigated in the circulating water channel and the wave tank for deducting the most stable buoy from the current and the wave condition. 5 types of buoy made up of short cylinder laid vertically (CL-V), short cylinder laid horizontally (CL-H), capsule (CS), sphere (SP) and long cylinder (CL-L) were used for experiments. A mooring line and a weight were connected with each buoy. A tensile gauge was installed between a mooring line and a weight. All buoy's mooring tension was measured at the same time for the wave test with periods of 1.5~3.0 sec and wave heights of 0.1~0.3 m, and the current test with flow speeds of 0.2~1.0 m/sec. As a result, the order of tension value in the wave test was CL-H > CL-V > SP > CS > CL-L. In the current test CL-V and CL-H were recorded in the largest tension value, whereas SP has the smallest tension value. So it seems that SP buoy is the most effective in the location affected by fast current. CS is predicted to be suitable for a location that influence of wave is important more than that of current if practical use in the field is considered. And it was found that the difference of mooring tension among buoys in wave is related to the product of the cross sectional area and the drag coefficient for the buoy's bottom side in high wave height. The factor for the current condition was not found. But it was supposed to be related to complex factors like a dimension and a shape by buoy's posture to flow.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.489-497
• /
• 2016

레일체결장치는 레일을 침목 등에 결속시켜 정해진 궤간의 유지와 열차 하중을 하부의 침목 및 도상 등에 전달하는 역할을 수행하는 주요 궤도 구성품이다. 본 논문에서는 도시철도 운영환경에서 파상마모에 대한 레일체결장치 클립의 진동 특성 분석을 위해서 조립상태에서 레일체결장치 클립의 모달테스트를 수행하여 고유진동수를 측정하였으며, 이를 파상마모에 의한 통과주파수와의 비교를 통해 공진 영향을 검토하였다. 또한 열차 주행시 파상마모에 따른 레일 및 레일체결장치 클립의 가속도와 레일체결장치 클립의 변형률을 계측하였다. 분석결과 레일 및 레일체결장치 클립의 가속도는 파상마모와 매우 밀접한 관계를 가지고 있으나, 레일체결장치 클립의 변형률과의 관계는 미비한 것으로 나타났다.

• Advances in concrete construction
• /
• 제11권5호
• /
• pp.375-386
• /
• 2021

In this paper, a study of stability and health of a newly-built railway tunnel is presented. The field test was implemented to monitor the secondary lining due to the significant cracking behaviors influenced the stability and health of the tunnel structure. Surface strain gauges were installed for monitoring the status of crack openings, and the monitoring outputs demonstrated that the cracks were still in the developing stage. Additionally, adjacent tunnel and poor condition of surrounding rock were identified as the causes of the lining cracking by systematically characterizing the crack spatial distribution, tunnel site and surrounding rock conditions. Reconstruction of partial lining and reconstruction of the whole secondary lining were designed as the maintenance projects for different cracking regions based on the construction feasibility. For assessing the health conditions of the reinforced lining, embedded strain gauges were set up to continuously measure the strain and the internal force of the reconstructed structures. For the partially reconstructed lining, the outputs show the maximum tensile elongation is 0.018 mm during 227 days, which means the structure has no obvious deformation after maintenance. The one-year monitoring of full-section was implemented in the other two completely reconstructed cross-sections by embedded strain gauge. The outputs show the reconstructed secondary lining has undertaken the pressure of surrounding rock with the time passing. According to the calculated compressive and tensile safety factors, the completely reconstructed lining has been in reliable and safe condition during the past year after reinforcement. It can conclude that the aforementioned maintenance projects can effectively ensure the stability and health of this tunnel.

• 천문학회보
• /
• 제44권2호
• /
• pp.69.2-69.2
• /
• 2019

To construct a coronal force-free magnetic field, we must impose the boundary normal current density (or three components of magnetic field) as well as the boundary normal field at the photosphere as boundary conditions. The only method that is known to implement these boundary conditions exactly is the method devised by Grad and Rubin (1958). However, the Grad-Rubin method and all its variations (including the fluxon method) suffer from convergence problems. The magnetofrictional method and its variations are more robust than the Grad-Rubin method in that they at least produce a certain solution irrespective of whether the global solution is compatible with the imposed boundary conditions. More than often, the influence of the boundary conditions does not reach beyond one or two grid planes next to the boundary. We have found that the 2D solenoidal gauge condition for vector potentials allows us to implement the required boundary conditions easily and effectively. The 2D solenoidal condition is translated into one scalar function. Thus, we need two scalar functions to describe the magnetic field. This description is quite similar to the Chandrasekhar-Kendall representation, but there is a significant difference between them. In the latter, the toroidal field has both Laplacian and divergence terms while in ours, it has only a 2D Laplacian term. The toroidal current density is also expressed by a 2D Laplacian. Thus, the implementation of boundary normal field and current are straightforward and their effect can permeate through the whole computational domain. In this paper, we will give detailed math involved in this formulation and discuss possible lateral and top boundary conditions and their meanings.

• 한국재난정보학회 논문집
• /
• 제16권3호
• /
• pp.449-457
• /
• 2020

연구목적:서울시는 공동관리 등급 기준에 따라 공동의 규모, 아스팔트포장 두께, 포장면의 균열깊이를 고려하여 긴급, 우선, 일반, 관찰등급으로 공동의 위험도를 분류하고 있다. 본 연구에서는 2019년 서울시 공동조사용역에서 발견된 265개소의 공동의 상부 포장상태를 확인하여 포장균열이 확인된 17개소에 대하여 균열깊이를 측정하였다. 연구방법: 1차에서는 확인된 공동의 균열 확인을 위하여 버니어 캘리퍼스, 테이퍼 게이지, 깊이 게이지를 활용하여 균열 폭 및 깊이를 측정하였다. 2차에서는 상부 노면에서 가장 크게 균열이 발생한 위치를 확인하여 아스콘을 천공 후 균열 깊이를 추가로 측정하였다. 연구결과:확인된 시험공동 17개소 중 9개소에서 공동 관리 등급이 상향 조정되었다. 따라서, 긴급복구와 우선복구의 경우에는 포장 균열 깊이와 잔여 아스팔트 콘크리트 포장 두께에 따라 등급 조정이 필요하다. 결론:공동 상부에 균열이 발생한 경우는 천공을 통하여 균열 진행 상태를 파악하고 잔여 아스팔트 콘크리트 두께를 확인하여 공동등급을 결정해야한다.

• 한국농공학회지
• /
• 제18권2호
• /
• pp.4116-4120
• /
• 1976

With the use of many rivers increased nearly to the capacity, the need for information concerning daily quantities of water and the total annual or seasonal runoff has became increased. A systematic record of the flow of a river is commonly made in terms of the mean daily discharge Since. a single observation of stage is converted into discharge by means of rating curve, it is essential that the stage discharge relations shall be accurately established. All rating curves have the looping effect due chiefly to channel storage and variation in surface slope. Loop rating curves are most characteristic on streams with somewhat flatter gradients and more constricted channels. The great majority of gauge readings are taken by unskilled observers once a day without any indication of whether the stage is rising or falling. Therefore, normal rating curves shall show one discharge for one gauge height, regardless of falling or rising stage. The above reasons call for the correction of the discharge measurements taken on either side of flood waves to the theoretical steady-state condition. The correction of the discharge measurement is to consider channel storage and variation in surface slope. (1) Channel storage As the surface elevation of a river rises, water is temporarily stored in the river channel. There fore, the actual discharge at the control section can be attained by substracting the rate of change of storage from the measured discharge. (2) Variation in surface slope From the Manning equation, the steady state discharge Q in a channel of given roughness and cross-section, is given as {{{{Q PROPTO SQRT { 1} }}}} When the slope is not equal, the actual discharge will be {{{{ { Q}_{r CDOT f } PROPTO SQRT { 1 +- TRIANGLE I} CDOT TRIANGLE I }}}} may be expressed in the form of {{{{ TRIANGLE I= { dh/dt} over {c } }}}} and the celerity is approximately equal to 1.3 times the mean watrr velocity. Therefore, The steady-state discharge can be estimated from the following equation. {{{{Q= { { Q}_{r CDOT f } } over { SQRT { (1 +- { A CDOT dh/dt} over {1.3 { Q}_{r CDOT f }I } )} } }}}} If a sufficient number of observations are available, an alternative procedure can be applied. A rating curve may be drawn as a median line through the uncorrected values. The values of {{{{ { 1} over {cI } }}}} can be yielded from the measured quantities of Qr$.$f and dh/dt by use of Eq. (7) and (8). From the 1/cI v. stage relationship, new vlues of 1/cI are obtained and inserted in Eq. (7) and (8) to yield the steady-state discharge Q. The new values of Q are then plotted against stage as the corrected steadystate curve.