• Journal of Korean Society on Water Environment
• /
• v.20 no.1
• /
• pp.37-41
• /
• 2004

This paper was studied about the characteristics of treatment by ionized gas for livestock wastewater, aiming at the effects of ionized gas on organic matter, hydrophobic and hydrophilic organic matter in livestock wastewater when the new process of advanced oxidation process was applied for meeting the improved the quality of effluent. The organic matter within treated livestock wastewater by ionized gas was partially mineralized according to the time increasement. The $TCOD_{Mn}$ in the livestock wastewater was decreased from 840mg/L to 340mg/L when treated by ionized gas by the enhancement of time. We occupied the equations of $TCOD_{Cr}$, $SCOD_{Cr}$, $TCOD_{Mn}$ and $SCOD_{Mn}$ as to ionized gas treated time. As $TCOD_{Mn}$ increasing ionized gas treated time, the concentration did not meet the water quality, $COD_{Mn}$ 4Omg/L. So, for removing of the remaining organic matter in the efflent after ionized gas, following process is necessary. After treating the livestock wastewater by ionized gas, coagulation was considerable for organic matter removal up to regulation water quality. From UV scans of the treated livestock wastewater by ionized gas, the wastewater has low aromaticity and good colour.

• Journal of the Korean Institute of Gas
• /
• v.10 no.3 s.32
• /
• pp.60-64
• /
• 2006

Explosion range and explosion characteristics of by product gas from carbon black manufacturing process were studied. About 75% of the by product gas were composed with water vapour and nitrogen. And the combustible component in the gas were hydrogen, methane, acetylene and carbon mono-oxide. Because of the combustible components in the by product gas there are explosion hazards in the gas handling process. Explosion range of the gas by experiment was from 17.1% to 70.7% and the value has considerable difference with the calculated value from Lechatelier law. Explosion pressure of the gas was $5.4kg/cm^2$ and the average explosion pressure rise rate was $39.2kg/cm^2/s$. Based on the experimental result we can expect that a explosion or fire accident during the handling the gas can make a severe loss, therefore there should be a explosion prevention or protection measures in the gas handling process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.5
• /
• pp.816-822
• /
• 2001

The thermoforming process is widely used in the plastics industry to produce articles for the packaging, automotive, domestic construction and leisure industries. The microcellular foaming process appeared at M.I.T. in 1980s to save a quantity of polymer materials and increase their mechanical properties. The glass transition temperature of polymer materials is one of many important process variables in appling the microcellular foaming process to the conventional thermoforming process. The goal of this research is to evaluate the relation between gas absorption and glass transition temperature in batch process using microcellular foaming process. The weight gain ratio of polymer materials has a conception of gas absorption. Polymers such as acrylonitrile-butadiene-styrene(ABS), polystyrene(PS) have been used in this experiment. According to conventional Chows model and Cha-Yoon model, it was estimated with real experimental result to predict a change of glass transition temperature as a function of the weight gain ratio of polymer materials in batch process to gain microcellular foamed plastic products.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.3
• /
• pp.52-57
• /
• 2004

Many kinds of gases, such as erosion gas, dilution gas, and toxic gas have been used in manufacturing process of LCD at semiconductor. In order to increase accumulation rate of manufacturing process, high degree of purity in these gases and minimized metalllic dust are required. All wetted stainless steel surface must be 316L electro-polished with $0254{\mu}m$ in average. Based on the AES analysis, Cr/Fe 11 and $Cr_2O_3$ thickness $25{\AA}$ are measured Molybdenum and silicon contaminants which is characteristic of stainless steel and oxygen were found on the surface.

• Polymer(Korea)
• /
• v.28 no.3
• /
• pp.263-272
• /
• 2004

Using computer simulation, the processibility and properties of the inst겨ment panel of automobile produced by gas injection molding were predicted and evaluated. The P-V-T data of ABS, resin were used in the gas injection molding process in order to estimate the mold filling phenomena. The optimum process conditions were found by adjusting the process parameters including pressure, filling time, the positions of gas channel and runner. The process was simplified and the final instrument panel produced by the gas injection molding was found to have improved dimension stability compared to the one produced by conventional injection molding.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.197-204
• /
• 2021

Pressure swing adsorption is a purification process which can get pure hydrogen. The purification process is composed of four process: compression, adsorption, desorption and discharge. In this study the adsorption process was simulated by using the Fluent and validated with experimental results. A gas used in experiment is composed of H₂, CO₂, CH₄, and CO. Adsorption process conducted under 313 kelvin and 3 bar and bituminous-coal-based (BPL) activated carbon was used as the adsorbent. Langmuir model was applied to explain the gas adsorption. And diffusion of all the gases was controlled by micro-pore resistances. The result shows that, the most adsorbed gas was carbon dioxide, followed by methane and carbon monoxide. And carbon monoxide took the least amount of time to reach the maximum adsorption amount. The molar fraction of the off-gas became the same as the molar fraction of the gas supplied from the inlet after adsorption reached the equilibrium.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1317-1321
• /
• 2009

Natural gas liquefaction plant and LNG carrier needs large capital investment. Therefore a lot of small or middle scale natural gas fields aren't developed due to poor profitability. If natural gas is made to gas hydrate instead of liquefaction, developing small-scale natural gas field can be profitable because building cost of gas hydrate plant and carrier are economical. Because the process of making gas hydrate consumes much energy, the gas hydrate formation process has to be optimized for energy consumption. In this study, gas hydrate formation process was investigated experimentally. Experimental apparatus consists of reactor, pressure regulator, chiller, and magnetic stirrer. 99.95% methane was used to make gas hydrate. Tests were conducted at variable pressure and temperature condition.

• Journal of the Korean Institute of Gas
• /
• v.17 no.4
• /
• pp.51-57
• /
• 2013

The process of liquefied natural gas is less then $-160^{\circ}C$ to natural gas by cooling at atmospheric pressure. When control strategy was made, one of the most significant is analysis of process. It is important to understand the control variable change according to manipulated variable change. In this study, we experiment natural gas liquefied process using C3MR(Propane Pre-cooled Mixed Refrigerant) process by BSU(Bench Scale Unit). We analyzed the change of refrigerant temperature and natural gas temperature according to the change of refrigerant flow rate so as to search an influence flow rate according to adjust each manipulated variables. One of the manipulated variable affected a number of control variables, but were able to confirm a control variable with a large response.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.8-10
• /
• 2007

In recent years, hydrogen-oxygen mixed gas generated by electrically dissociating water has been proposed as alternative cutting fuel. The mixed gas consists of a hydrogen-oxygen mixed gas in the mixture ratio of 2:1. And gas has some merits as cutting quality and speed compared with existing gas cutting process. Because main source of mixed gas is water, mixed gas is environmental-friendly clean fuel. The purpose of the present paper is to investigate cutting characteristics and optimum cutting parameters of mixed gas, The effect of cutting parameter on the cutting characteristics of mixed gas is also investigated as compared to existing gas cutting process.

• Journal of the Korean Society of Safety
• /
• v.22 no.4
• /
• pp.32-36
• /
• 2007

When the vacuum system for the process of $SiH_{4}$ gas used in the semiconductor and FPD field is partially vented from vacuum to atmospheric state, a fire often occurs due to auto-ignition of $SiH_{4}$ gas. In order to prevent the fire, the concentration of $SiH_{4}$ should be kept under LFL. This means that the higher capacity pump is needed to meet the process conditions as well as the condition that the concentration of $SiH_{4}$ should be kept under LFL. In this article, we conducted the injection of the dilution gas at the manifold between booster pump and dry pump compared with the typical method that the dilution gas was injected into inlet port of booster pump using computer simulation. According to the result, we can flow further more purge gas for safety without any change of the condition in the process chamber, which means that the higher capacity pump is not required for safety in some cases.