The purpose of this paper is to present the manufacturing defect and damage pattern of a 3 phase 22.9/3.3kV oil immersed transformer, as well as to present an objective basis for the prevention of a similar accident and to secure data for the settlement of PL related disputes. It was found that in order to prevent the occurrence of accidents to transformers, insulating oil analysis, thermal image measurement, and corona discharge diagnosis, etc., were performed by establishing relevant regulation. The result of analysis performed on the external appearance of a transformer to which an accident occurred, the internal insulation resistance and protection system, etc., showed that most of the analysis items were judged to be acceptable. However, it was found that the insulation characteristics between the primary winding and the enclosure, those between the ground and the secondary winding, and those between the primary and secondary windings were inappropriate due to an insulating oil leak caused by damage to the pressure relief valve. From the analysis of the acidity values measured over the past 5 years, it is thought that an increase in carbon dioxide (CO2) caused an increase in the temperature inside the transformer and the increase in the ethylene gas increased the possibility of ignition. Even though 17 years have passed since the transformer was installed, it was found that the system's design, manufacture, maintenance and management have been performed well and the insulating paper was in good condition, and that there was no trace of public access or vandalism. However, in the case of transformers to which accidents have occurred, a melted area between the upper and the intermediate bobbins of the W-phase secondary winding as well as between its intermediate and lower bobbins. It can be seen that a V-pattern was formed at the carbonized area of the transformer and that the depth of the carbonization is deeper at the upper side than the lower side. In addition, it was found that physical bending and deformation occurred inside the secondary winding due to non-uniform pressure while performing transformer winding work. Therefore, since it is obvious that the accident occurred due to a manufacturing defect (winding work defect), it is thought that the manufacturer of the transformer is responsible for the accident and that it is lawful for the manufacture to investigate and prove the concrete cause of the accident according to the Product Liability Law (PLL).
Objectives: This study aims to assess the concentrations of ammonia and hydrogen sulfide according to task unit area at swine farms. Methods: A total of six swine farms were selected for this study. Ammonia and hydrogen sulfide were monitored using a real-time multi-gas monitor which could sample the gases simultaneously. The sampling was done in the pig building, manure storage facility and composting facility of each farm. Results: The concentration of ammonia in the pig buildings(GM 22.6 ppm, GSD 2.3) was significantly higher(p<0.0001) than in the manure storage facilities(GM 10.4 ppm, GSD 2.7) and composting facilities(GM 8.6 ppm, GSD 2.8). The concentration of hydrogen sulfide in the manure storage facilities(GM 9.8 ppm, GSD 3.2) was higher(p<0.0001) than in the pig buildings(GM 2.3 ppm, GSD 2.3) and composting facilities(GM 1.9 ppm, GSD 2.5). In particular, the levels of hydrogen sulfide in the confined manure storage facilities were higher than those in open-type facilities and the peak concentration(98 ppm) in the confined facilities was approximate to 100 ppm, at the value of Immediately Dangerous to Life or Health(IDLH). Conclusions: Suffocation accidents caused by hazardous gases at a swine farm have occurred annually. Real-time monitoring of the hazards should be done in order to protect farm workers and livestock from the sudden accidents.
Guenot-Delahaie, Isabelle;Sercombe, Jerome;Helfer, Thomas;Goldbronn, Patrick;Federici, Eric;Jolu, Thomas Le;Parrot, Aurore;Delafoy, Christine;Bernaudat, Christian
Nuclear Engineering and Technology
/
제50권2호
/
pp.268-279
/
2018
The ALCYONE multidimensional fuel performance code codeveloped by the CEA, EDF, and AREVA NP within the PLEIADES software environment models the behavior of fuel rods during irradiation in commercial pressurized water reactors (PWRs), power ramps in experimental reactors, or accidental conditions such as loss of coolant accidents or reactivity-initiated accidents (RIAs). As regards the latter case of transient in particular, ALCYONE is intended to predictively simulate the response of a fuel rod by taking account of mechanisms in a way that models the physics as closely as possible, encompassing all possible stages of the transient as well as various fuel/cladding material types and irradiation conditions of interest. On the way to complying with these objectives, ALCYONE development and validation shall include tests on $PWR-UO_2$ fuel rods with advanced claddings such as M5(R) under "low pressure-low temperature" or "high pressure-high temperature" water coolant conditions. This article first presents ALCYONE V1.4 RIA-related features and modeling. It especially focuses on recent developments dedicated on the one hand to nonsteady water heat and mass transport and on the other hand to the modeling of grain boundary cracking-induced fission gas release and swelling. This article then compares some simulations of RIA transients performed on $UO_2$-M5(R) fuel rods in flowing sodium or stagnant water coolant conditions to the relevant experimental results gained from tests performed in either the French CABRI or the Japanese NSRR nuclear transient reactor facilities. It shows in particular to what extent ALCYONE-starting from base irradiation conditions it itself computes-is currently able to handle both the first stage of the transient, namely the pellet-cladding mechanical interaction phase, and the second stage of the transient, should a boiling crisis occur. Areas of improvement are finally discussed with a view to simulating and analyzing further tests to be performed under prototypical PWR conditions within the CABRI International Program. M5(R) is a trademark or a registered trademark of AREVA NP in the USA or other countries.
반도체, 디스플레이 등 IT(Information Technology) 제품 수요 증가로 관련 산업이 확대되고 있다. 이는 생산설비 증설과 화학물질 사용 증가로 이어지며 화재·폭발의 위험성에도 영향을 미치고 있다. 이러한 위험요인에 대해 정부는 오래전부터 인화성 물질을 제조·사용·취급하는 장소의 사고 예방을 위하여 산업안전보건법 및 KS 기준에 따라 폭발위험 장소로 설정하여 관리토록 하고 있다. 그러나, 폭발위험장소를 설정할 때, 중요한 요소인 환기량을 고려하지 않아 실질적인 폭발분위기 조성 가능성을 예측하기는 쉽지 않다. 이 연구에서는 디스플레이 산업에서 주요 공정인 CVD(Chemical Vapor Deposition) 설비에 SEMI S6 Exhaust Ventilation Test 방법을 적용하여 위험한 설비의 환기 성능을 평가하고, 폭발분위기 조성 가능성을 확인하였다. 그 결과, 가상의 시나리오 내에서 환기 성능이 SEMI S6에서 규정한 기준에 적합하였고, 폭발분위기가 조성될 가능성이 낮음을 확인하였다. 따라서, KS 규격뿐만 아니라 공학적 기법으로 폭발분위기의 형성 여부를 예측한 연구 결과를 통해 합리적이고 경제적인 사고 예방에 도움이 될 것으로 기대된다.
The purpose of this study was to investigate what life safety services the elderly living alone in rural areas need and to propose the life safety services that they actually need. The research subjects were 1,000 people aged 65 years and over living in the rural areas of Korea. Among the total 1,000 respondents, 283 elderly people who did not live together with their married children were included in this study. Data were analyzed through frequency analysis, descriptive statistics, and multiple regression analysis. The results of this study were as follows. First, the needs of health care services and vehicle support services (when the elderly went to the hospital or walked out) were high. These were services related to health, which means that the health of the elderly is not good and that they are interested in health. Of course, it is important to treat the disease. However, it is more important to prevent disease and maintain health. An expansion of these services is urgently needed. Second, the need for life safety services was affected by the frequency of contact with neighbors, uncomfortable housing, exercise, the frequency of contact with children, gas accidents, and nutrition variables. Through this analysis, we propose to include the housing improvement service, nutrition improvement services, and expanding social relations services in the life safety services.
현대사회에서는 통신 전기 상하수도 가스 등 도시기반 시설물들을 지하에 매설하게 되면서 굴착공사로 인한 많은 사고 위험을 내재하게 되었다. 사고를 방지하기 위해서는 매설된 지하시설물에 대한 정확한 위치와 속성정보가 구축되어야 한다. 하지만 2004년부터 2009년까지 상수관로의 공공측량성과심사를 분석한 결과, 관로매설 전 시행하는 위치측량은 신규관로만을 관측하며 전자유도 탐사는 콘크리트 구간에서 자장간섭으로 인한 탐지 불가와 금속관로만을 탐사하는 한계점으로 인해 52.4%의 저조한 탐사율을 보이고 있다. 따라서 탐사율을 향상할 수 있는 정확하고 효과적인 탐사 기법에 대한 개발과 검증이 필요하다. 본 연구에서는 매설 전 금속관로와 비금속관로에 대한 위치측량 결과를 기준으로 정하여 지중레이더와 전자유도탐사를 통해 얻은 값과 비교 분석하였다. 그 결과 콘크리트구간 100%, 비포장구간 94.7%, 아스팔트구간 60%의 탐사율을 보여 지하매설물 탐사 시에 지중레이더 탐사의 적용가능성을 확인하였다.
고온에서 운전되는 플랜트에서는 열변형에 의한 배관 사고를 예방하고 배관계통의 우선 검사관리 부위의 선정을 위해 배관 시스템하중 해석을 수행하는 경우가 많다. 본 연구에서는 국내 한 공정플랜트에서 설계변경에 따라 반응기와 반응기 사이에 추가 설치된 연결배관을 대상으로 배관 시스템응력해석을 수행하였다. 특히 배관에 일반적으로 설치되는 하중행거(hanger) 이외에 열팽창을 흡수하는 신축이음(expansion joint)이 함께 설치된 경우의 배관 특성을 연구하였다. 이를 위해 배관 응력을 형성하는 구조적 요인의 영향을 평가하기 위해 배관계에 포함된 행거와 신축이음이 비정상적으로 작동되는 경우도 가정하여 해석하였다. 추가적인 인입라인이 있는 경우도 해석을 수행하였다. 정상 운전 시 배관계의 시스템 응력 결과와 비정상적인 운전 경우의 해석결과를 비교하여 각각 배관요소의 역할을 연구하였다.
According to the National Fire Data System (NFDS), more than 5,000 vehicle fires have occurred every year for the last 10 years. Vehicle fires are primarily caused by mechanical (breaking system and engine), electrical (wiring and battery), and chemical (oil and fuel gas leakage) problems. The electrical factor has increased with the installation of driver convenience equipment. For example, today, the black box is widely used to provide video data recording of motor vehicle accidents. The black box consists of a front camera, rear camera, and wires. The black box wires are directly connected to the junction box or fuse box from the start battery that operates to provide normal on power supplying for engine stop. It is extremely dangerous when the wires short circuit due to insulation aging, mechanical and electrical stress, etc. In this study, the black box wiring fire risk have been analyzed and investigated when the steady state and abnormal operations, and under the following conditions: wiring arrangements with a high temperature condition, insulation aging, poor contact, and short circuits. The results showed that black box wiring short circuits had a higher fire risk than the other fire hazard elements. To prevent fire hazards caused by black box wiring, the black boxes must be installed by qualified service personnel. Do not modify the wiring, remove the fuse and secure the wiring using cable ties or insulation tape.
국내 천연가스 수요의 동고하저의 수요패턴과 도입패턴의 불일치 및 저장시설의 한계 등으로 수급관리의 어려움이 내재하고 있고 LNG 생산지 사고 등 도입선 공급불안 요인이 상존하고 있다. 따라서 LNG의 안정적 수급관리를 위하여 장기간 저장이 가능한 대규모 저장시설의 확보가 매우 중요한 실정이다. 이에 한국지질자원연구원에서 Pilot Plant 운영을 통하여 검증된 복공식 저장공동기술의 국내 적용성 여부를 검토하고자 한다. 이 기술은 기존의 지상식과 반지하식에 비하여 경제성 안전성 및 환경친화성 등에 유리하며 특히 기화율 저감으로 인한 LNG 장기 저장이 가능하다는 장점을 가지고 있다. 따라서 LNG 지하공동 비축시스템의 국내 도입을 위하여 지하저장기술의 기술적 타당성 건설 및 운영비용 등에 대하여 살펴보았다.
At present, the time of easy oil and gas is over. Now, the largest part of fossil fuels is concentrated in the deepest levels of tectonic structures and in the sea shelves. One of the most cumbersome operations of their extraction is the bore-hole drilling. In connection with austere tectonic and climate conditions, their drivage every so often is associated with great and diversified technological difficulties causing emergencies on frequent occasions. As a rule, they are linked with drill string accidents. A key role in prediction of these situations should play methods of theoretical modelling. For this reason, there is a growing need for development and implementation of new numerical methods for computer simulation of critical and post-critical behavior of drill strings (DSs). In this paper, the processes of non-linear deforming of a DS in cylindrical cavity of a deep bore-hole are considered. On the basis of the theory of curvilinear flexible rods, non-linear constitutive differential equations are deduced. The effects of the longitudinal non-uniform preloading, action of torque and interaction between the DS and the bore-hole surface are taken into account. Owing to the use of curvilinear coordinates in the constraining cylindrical surface and a specially chosen concomitant reference frame, it became possible to separate the desired variables and to reduce the total order of the equation system. To solve it, the method of continuation the solution by parameter and the transfer matrix technique are applied. As a result of the completed numerical analysis, the critical states of the DS loading in the cylindrical channels of inclined bore-holes are found. It is shown that the modes of the post-critical deforming of the DS are associated with its irregular spiral curving prevailing in the zone of bottom-hole-assembly. The possibility of invariant state generation during post-critical deforming is established, condition of its bifurcation is formulated. It is shown that infinite variety of loads can correspond to one geometrical configuration of the DS. They differ each from other by contact force functions.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.