• Journal of Korean Society for Quality Management
• /
• v.39 no.4
• /
• pp.527-542
• /
• 2011

The importance of service industry in national economy is getting increasing due to current trend of aging society and increasingly desire for better quality of life. However, the level of labor productivity in domestic service industry is lower than Japan and Germany that are typically strong in manufacturing industry. Difficulty of process control and measurement in accordance with variability and intangibility which are features of service industry, is considered as the cause of this poor labor productivity in Korea. This study aims to present managerial implications by calculating sigma levels on branch bank service quality and suggesting the quality dimensions of banks can be checked through a gap comparison between the sigma level on service quality in the whole banks and service quality in each bank. Quality level presented by the KS-SQI is applied to the measurement method that Yoo Han Joo and Song Kwang Seok suggested in 2006. Spss18.0 is used as an analysis tool. As a result of factorial analysis, 7 dimensions of service quality in KS-SQI can be divided into new 3 dimensions of service quality. This study also suggests that width and number of questions in previous questionnaire shall be extended. The whole of the bank service quality level is evaluated 3 sigma. The research help banks to figure out their service quality level through gap comparison objectively.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.2
• /
• pp.75-82
• /
• 1999

A compensation method of the motor parameters using zero sequence third harmonic voltage is presented for the speed sensorless vector control of the induction motor considering saturation of the flux. Generally, the air-gap flux of the saturated induction motor contains the space harmonic components rotating with the synchronous frequency of the motor. Because the EMF of the saturated induction motor contains the zero sequence harmonic voltages at the neutral point of the motor, those harmonic voltages can be used as a saturation index. In this work, the rotor flux observer is firstly designed for the speed sensorless vector control of induction motor. And a novel measurement method of the space harmonic voltage and a compensation method of th LPF(Low Pass Filter) are proposed. For compensating the non-linear variations of the magnetizing inductance depending on the saturation level of the motor, the dominant third harmonic voltage of the motor is used as a saturation function of the air-gap flux. And the variation of the stator resistance owing to the motor temperature can also be measured with the phase angle between the impressed voltage vector and the zero sequence voltage. The validity of the proposed parameter compensation scheme in the speed sensorless vector control using rotor flux observer is verified by the result of the simulations and the experiments.

• Journal of The Korean Society of Integrative Medicine
• /
• v.8 no.2
• /
• pp.97-107
• /
• 2020

Purpose : The purpose of this study is to investigate the effect of squat exercise using a ball on the gap between knees and Q angle of a subject with a genu-varum, and to prove the effect, to provide a clinical basis for developing into a knee correction exercise program. Methods : As a result of posture measurement through GPS, 26 female with genu-varum with a knee length of 5 cm or more were studied. The group was randomly assigned to 13 squat exercise group using ball (experimental group) and 13 general squat exercise groups (control group). The experimental group placed the ball between both knees in a position where the distance between both feet was slightly wider than the shoulder width on a flat support surface, and fixed the ball, and then squat with the start signal. The control group squats without a ball. Each group performed three sets of exercise three times a week for six weeks. Before their exercise, after three and six weeks, EMG, GPS, digital goniometer measurement, the vastus medialis (VM), the vastus lateralis (VL), and the Q-angle were measured in the squat exercise posture. EMG was measured in squat exercise posture. Results : The distance between the knees was reduced. EMG is activated in group A, the group B experimental results showed the high activity of the VL. Q-angle had increased. But the experimental group increased more than the control group. Conclusion : We have confirmed through our experiments that the distance interval between the knees during squat exercises using a ball can be reduced. Furthermore, it would also be helpful to ensure the treatment of genu-varum.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.9
• /
• pp.877-882
• /
• 2011

In this paper, thermal deformation of a double ring structure using digital image correlation technique (DIC) was measured. The double ring structure consisted of two parts; the inner ring was aluminium which had a large thermal expansion coefficient and the outer ring was titanium which had a small thermal expansion coefficient. We heated the double ring structure from $50^{\circ}C$ to $200^{\circ}C$ in a chamber and at the same time, two cameras captured surface images of the double ring structure. Initially, there was a 21 ${\mu}m$ gap between the inner ring and outer ring. The gap was closed at around $80^{\circ}C$ and after that, two rings expanded together. In order to compare the experimental results with analysis results, a finite element analysis was performed using ANSYS. The results of DIC measurement and ANSYS analysis were compared and agreed well.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.1
• /
• pp.49-55
• /
• 2011

Sound insulation performance of a unit cabin mock-up is studied, where two identical rooms simulating cruise ship cabin are installed. STL (Sound Transmission Loss) measurement in the mock-up shows that STL of the partition between rooms is degraded by imperfect door ceiling and gap between wall and floor. It is also observed that gap around lighting and electrical outlet slightly affect the STL in high frequency ranges, since lighting and electrical outlet are supported by mineral wool in the back side due to fire-resistance requirement. Even after all possible gaps are sealed, STL of the partition is found to be lower than that measured in the laboratory by 9 dB. Measurement of SBN (Structure-Borne Noise) reveals that flanking transmission of SBN along the steel deck floor can severely deteriorate STL of the partition. Statistical energy analysis (SEA) of the mock-up confirms importance of the floor SBN control, in which increasing damping is essential to ensure high STL.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.4
• /
• pp.293-297
• /
• 2020

This paper tried to find the best conditions that could be applied to solar cells by deposition of CdS thin film on ITO glass using multiplex displacement sputter system. RF power was changed to 50W, 100W, and 150W and sputtering time was set to 10 minutes. As a result of the measurement of transmittance, the average transmittance in the area of 400 to 800 nm was measured from 60% to 80% and the best characteristic was measured at 150W at 84%. The band gap was also measured at 3.762eV at 50W, 4.037eV at 100W and 4.052eV at 150W. In XRD analysis, even as RF power was increased, it was observed as a structure called Wurtzite (hexagonal) of CdS. And as RF power increased, the particles were large and uniformly deposited, but at 100W the particles were densely composed and dense. And the thickness measurement showed that the RF power increased uniformly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.167-168
• /
• 2007

$CdIn_2S_4$ (110) films were grown on semi-insulating GaAs (100) by a hot wall epitaxy method. Using photocurrent (PC) measurement, the PC spectra in the temperature range of 30 and 10 K appeared as three peaks in the short wavelength region. It was found that three peaks, A-, B-, and C-excitons, correspond to the intrinsic transition from the valence band states of ${\Gamma}_4(z),\;{\Gamma}_5(x),\;and\;{\Gamma}_5(y)$ to the exciton below the conduction band state of ${\Gamma}_1(s)$, respectively. The 0.122 eV crystal field splitting and the 0.017 eV spin orbit splitting were obtained. Thus, the temperature dependence of the optical band gap obtained from the PC measurement was well described by $E_g$(T)=2.7116eV - $(7.65{\times}10^{-4}\;eV/K)T^2$/(425+T). But, the behavior of the PC was different from that generally observed in other semiconductors. The PC intensities decreased with decreasing temperature. This phenomenon had ever been reported at a PC experiment on the bulk crystals grown by the Bridgman method. From the relation of log $J_{ph}$ vs 1/T, where $J_{ph}$ is the PC density, two dominant levels were observed, one at high temperatures and the other at low temperatures. Consequently, the trapping centers due to native defects in the $CdIn_2S_4$ film were suggested to be the causes of the decrease in the PC signal with decreasing temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.92-96
• /
• 2002

A silver indium sulfide $(AgInS_{2})$ epilayer was grown by the hot wall epitaxy method, which has not been reported in the literature. The grown $AgInS_{2}$ epilayer has found to be a chalcopyrite structure and evaluated to be high quality crystal. From the photocurrent measurement in the temperature range from 30 K to 300 K, the two peaks of A and B were only observed, whereas the three peaks of A, B, and C were seen in the PC spectrum of 10 K. These peaks are ascribed to the band-ta-band transition. The valence band splitting of $AgInS_{2}$ was investigated by means of the photocurrent measurement. The crystal field splitting, $\Delta_{cr}$, and the spin orbit splitting, $\Delta_{so.}$ have been obtained to be 0.150 eV and 0.009 eV at 10 K, respectively. And, the energy band gap at room temperature has been determined to be 1.868 eV. Also, the temperature dependence of the energy band gap, $E_{g}(T)$, was determined.

• Korean Journal of Materials Research
• /
• v.12 no.7
• /
• pp.587-590
• /
• 2002

A silver indium sulfide ($AgInS_2$) epilayer was grown by the hot wall epitaxy method, which has not been reported in the literature. The grown $AgInS_2$ epilayer has found to be a chalcopyrite structure and evaluated to be high quality crystal. From the photocurrent measurement in the temperature range from 30 K to 300 K, the two peaks of A and B were only observed, whereas the three peaks of A, B, and C were seen in the PC spectrum of 10 K. These peaks are ascribed to the band-to-band transition. The valence band splitting of $AgInS_2$ was investigated by means of the photocurrent measurement. The crystal field splitting, $\Delta_{cr}$ , and the spin orbit splitting, $\Delta_{so}$ , have been obtained to be 0.150 eV and 0.009 eV at 10 K, respectively. And, the energy band gap at room temperature has been determined to be 1.868 eV. Also, the temperature dependence of the energy band gap, $E_{g}$(T), was determined.d.

• Journal of Korean Society of Transportation
• /
• v.28 no.3
• /
• pp.157-167
• /
• 2010

Density is the most important congestion indicator among the three fundamental flow variables, flow, speed and density. Measuring density in the field has two different ways, direct and indirect. Taking photos with wide views is one of direct ways, which is not widely used because of its cost and lacking of proper positions. Another direct density measuring method using two point detectors has been introduced with the concept of instantaneous density, average density and measurement interval. The relationship between accuracy and measurement interval has been investigated using the SIMULATION data produced by Paramics Application Programming Interface function. We analyze the affect of segment density accuracy by sensing gap each road condition such as sensing segment length, lane and LOS after gathering data by Paramics Application Programming Interface.