• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.455-462
• /
• 2012

Al-Si coated boron steel and Zn coated DP steel plates were laser-welded to manufacture a Tailor Welded Blank (TWB) for a car body frame. Hot-stamping heat treatment ($900^{\circ}C$, 5 min) was applied to the TWB weld, and the microstructural change and transformation mechanism were investigated in the Al-rich area near the bond line of the Al-Si coated steel side. There was Al-rich area with a single phase, $Fe_3(Al,Si)$, which was transformed to ${\alpha}-Fe$ (Ferrite) after the heat treatment. It could be explained that the $Fe_3(Al,Si)$ phase was transformed to ${\alpha}-Fe$ during heat treatment at $900^{\circ}C$ for 5 min and the resultant ${\alpha}-Fe$ phase was not transformed by rapid cooling. Before the heat treatment, the microstructures around the $Fe_3(Al,Si)$ phase consisted of martensite, bainite and ${\alpha}-Fe$ while they were transformed to martensite and ${\delta}-Fe$ after the heat treatment. Due to the heat treatment, Al was diffused to the $Fe_3(Al,Si)$ and this resulted in an increase of Al content to 0.7 wt% around the Al-rich area. If the weld was held at $900^{\circ}C$ for 5 min it was transformed to a mixture of austenite (${\gamma}$) and ${\delta}-Fe$, and only ${\gamma}$ was transformed to the martensite by water cooling while the ${\delta}-Fe$ was remained unchanged.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1248-1254
• /
• 2018

Magnetization versus temperature and magnetic-field measurements, M(T, $H_a$), have been carried out to study the magnetic and critical properties of polycrystalline $La_{1-x}Ba_xCoO_3$ (x = 0.3 and 0.5) cobaltites. These compounds with the density of ${\sim}6.2g/cm^3$ crystallized in the $R{\bar{3}}c$ rhombohedral and $Pm{\bar{3}}m$ cubic structures, respectively. With an applied field $H_a=200Oe$, M(T) data have revealed that the samples with x = 0.3 and 0.5 exhibit the ferromagnetic-paramagnetic (FM-PM) phase transition at the Curie temperature points $T_C=202$ and 157 K, respectively. At 4.2 K, the saturation magnetization ($M_{sat}$) decreases from 35.9 emu/g for x = 0.3-26.1 emu/g for x = 0.5. Particularly, the critical-behavior analyses in the vicinity of $T_C$ reveal all samples undergoing a second-order phase transition, with critical exponent values (${\beta}=0.328$ and ${\gamma}=1.251$ for x = 0.3, and ${\beta}=0.331$ and ${\gamma}=1.246$ for x = 0.5) close to those expected for the 3D Ising model. This proves short-range magnetic order existing in $La_{1-x}Ba_xCoO_3$. We believe that magnetic inhomogeneities due to the mixture of hole-rich FM regions (confined in the trivalent-cobalt hole-poor anti-FM matrix) and uniaxial anisotropy prevent long-range order in $La_{1-x}Ba_xCoO_3$.

• Korean Journal of Metals and Materials
• /
• v.47 no.11
• /
• pp.716-721
• /
• 2009

The major drive for the application of low-temperature plasma treatment in nitrocarburizing of austenitic stainless steels lies in improved surface hardness without degraded corrosion resistance. The low-temperature plasma nitrocarburizing was performed in a gas mixture of $N_{2}$, $H_{2}$, and carbon-containing gas such as $CH_{4}$ at $450^{\circ}C$. The influence of the processing time (5~30 h) and $N_{2}$ gas composition (15~35%) on the surface properties of the nitrocarburized layer was investigated. The resultant nitrocarburized layer was a dual-layer structure, which was comprised of a N-enriched layer (${\gamma}_N$) with a high nitrogen content on top of a C-enriched layer (${\gamma}_C$) with a high carbon content, leading to a significant increase in surface hardness. The surface hardness reached up to about $1050HV_{0.01}$, which is about 4 times higher than that of the untreated sample ($250HV_{0.01}$). The thickness of the hardened layer increased with increasing treatment time and $N_{2}$ gas level in the atmosphere and reached up to about $25{\mu}m$. In addition, the corrosion resistance of the treated samples without containing $Cr_{2}N$ precipitates was enhanced than that of the untreated samples due to a high concentration of N on the surface. However, longer treatment time (25% $N_{2}$, 30 h) and higher $N_{2}$ gas composition (35% $N_{2}$, 20 h) resulted in the formation of $Cr_{2}N$ precipitates in the N-enriched layer, which caused the degradation of corrosion resistance.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.1037-1048
• /
• 2022

A radioactive isotope identification algorithm is a prerequisite for a low-resolution scintillation detector applied to an unmanned radiation monitoring system. In this paper, a sparse representation with dictionary learning approach is proposed and applied to plastic gamma-ray spectra. Label-consistent K-SVD was used to learn a discriminative dictionary for the spectra corresponding to a mixture of four isotopes (¹³³Ba, ²²Na, ¹³⁷Cs, and ⁶⁰Co). A Monte Carlo simulation was employed to produce the simulated data as learning samples. Experimental measurement was conducted to obtain practical spectra. After determining the hyper parameters, two dictionaries tailored to the learning samples were tested by varying with the source position and the measurement time. They achieved average accuracies of 97.6% and 98.0% for all testing spectra. The average accuracy of each dictionary was above 96% for spectra measured over 2 s. They also showed acceptable performance when the spectra were artificially shifted. Thus, the proposed method could be useful for identifying radioisotopes in gamma-ray spectra from a plastic scintillation detector even when a dictionary is adapted to only simulated data. Furthermore, owing to the outstanding properties of sparse representation, the proposed approach can easily be built into an insitu monitoring system.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.4
• /
• pp.215-223
• /
• 1992

This study has been performed to investigate into some effects of temperature, gas mixing ratio and time on the optical microstructure, hardness and wear characteristics of medium carbon alloy steel treated by plasma nitriding. The results obtained from the experiment are summarized as follows: (1) Optical micrographs of AISI 4140 steel plasma-nitrided by the double stage technique have revealed that the nitrided layer is composed of the compound layer and the diffusion layer. The variation in temperature at the first stage gives effects, on the formation of compound layer and the growth rate is shown to be relatively fast at $460^{\circ}C$. (2) The thickness of compound layer has been found to increase with increasing nitrogen percentage in the gas mixture and the holding time. It is therefore recommended that a shorter holding time and a lower nitrogen percentage are more effective to produce a tougher compound layer and a diffusion layer only. (3) X-ray diffraction analysis for AISI 4140 steel has shown that the compound layer consist of ${\gamma}^{\prime}-Fe_4N$ and ${\alpha}-Fe$ and that tough compound layer diffustion layer only can be obtained by the double stage plasmanitriding process. (4) There is also a tendency that the total hardened layer depth increases with increasing temperature, time and nitrogen percentage in the first stage during the double stage plasma nitriding. (5) The wear resistance of plasma nitrided specimens has been found thobe considerably increased compared to the untreated specimens and the amount of increment has appeared to increase further with increasing nitriding temperature, holding time and notrogen percentage of gas mixture in the first stage treatment.

• Journal of the Korean Society of Safety
• /
• v.32 no.5
• /
• pp.157-167
• /
• 2017

Millions of People die every year from diseases caused by exposure to outdoor air pollution. Especially, one of the most severe types of air pollution is fine particulate matter (PM10, PM2.5). South Korea also has been suffered from severe PM. This paper analyzes regional risks induced by PM10 and PM2.5 that have affected domestic area of Korea during 2014~2016.3Q. We investigated daily maxima of PM10 and PM2.5 data observed on 284 stations in South Korea, and found extremely high outlier. We employed extreme value distributions to fit the PM10 and PM2.5 data, but a single distribution did not fit the data well. For theses reasons, we implemented extreme mixture models such as the generalized Pareto distribution(GPD) with the normal, the gamma, the Weibull and the log-normal, respectively. Next, we divided the whole area into 16 regions and analyzed characteristics of PM risks by developing the FN-curves. Finally, we estimated 1-month, 1-quater, half year, 1-year and 3-years period return levels, respectively. The severity rankings of PM10 and PM2.5 concentration turned out to be different from region to region. The capital area revealed the worst PM risk in all seasons. The reason for high PM risk even in the yellow dust free season (Jun. ~ Sep.) can be inferred from the concentration of factories in this area. Gwangju showed the highest return level of PM2.5, even if the return level of PM10 was relatively low. This phenomenon implies that we should investigate chemical mechanisms for making PM2.5 in the vicinity of Gwangju area. On the other hand, Gyeongbuk and Ulsan exposed relatively high PM10 risk and low PM2.5 risk. This indicates that the management policy of PM risk in the west side should be different from that in the east side. The results of this research may provide insights for managing regional risks induced by PM10 and PM2.5 in South Korea.

• Journal of the East Asian Society of Dietary Life
• /
• v.16 no.1
• /
• pp.99-106
• /
• 2006

New application of rice was carried out by coating the rice with the mixture solution of ginseng and chungkukjang water extract The physicochemical characteristics of the coated rice were investigated. Moisture content of uncoated (15.26%) and coated rice$(15.57\sim15.66%)$ was not different significantly. The contents of crude protein, crude fat, and crude ash of the coated rice were higher as much as $4.28\sim11.82%\;8.47\sim47.46%$, and $11.54\sim42.31%$ than those of control, respectively. As total free amino acids in coated rice were increased by augmenting the amount of the extract, total free amino acids according to rate was increased to $3.1\sim7.8$ times. The major amino acids in the coated rice was alanine$(19.56\sim39.88\;mg%)$, leucine$(5.14\sim17.66\;mg%)$, and proline$(9.98\sim16.82\;mg%)$. Of those amino acids, alanine and $\gamma-aminobutyric$ acid in only coated rice were detected to the level of $19.56\sim39.88\;mg%$ and $7.78\sim12.36\;mg%$ respectively. The calcium amount of coated rice was increased to 15% to 20%. As increasing the coating rate, hardness, cohesiveness, chewiness, and brittleness of coated rice were decreased, but springiness was increased. Before cooking, the color of coated rice appeared yellow and after cooking turned to the light yellow. The color intensity was increased feasibly as increasing the coating rate. The sensory characteristic of rice coated manufactured by adding 15% of the extract was best and found to be similar to that of the control.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.996-1004
• /
• 1991

In this study, we tried to synthesis iron hydroxide suitable for longitudinal magnetic recording media from waste acid, which is a by-product of an iron works factory. Effects of initial pH of reactants, reaction temperature, reaction time for the synthesis of acicular iron hydroxide were studied in relation to particle properties of iron hydroxide and magnetic properties of maghemite powders. As the pH in reactant solution increased, $\beta$-FeOOH(pH=4.5), mixture of $\beta$-FeOOH and $\alpha$-FeOOH(4.5$\alpha$-FeOOH and Fe3O4(6.4$\alpha$-FeOOH (pH>13) was found to from in order. Especially, $\alpha$-FeOOH formed above pH 13 was single phase with superior acicularity. The temperature range over which the single-phase goethite can be formed increased as the initial pH of reactants increased (pH 13:10~5$0^{\circ}C$, pH 13.2:10~7$0^{\circ}C$, pH 13.5:0~8$0^{\circ}C$). The goethite formed between 40~6$0^{\circ}C$ has superior characteristics because the acicularity increased with increasing temperature but at high temperature (>6$0^{\circ}C$) Fe3O4 (pH=13) was found to start to form. Generally, single phase of goethite was found to form after one hour when an optimized condition. The particle size of goethite did not change as the reaction time increased over one hour. Accordingly, the magnetic properties of ${\gamma}$-Fe2O3 produced from goethite were not altered.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.5
• /
• pp.394-399
• /
• 1994

The catalytic mechanism of malonyl-CoA synthetase from Rhizobium trifolii was investigated by the steady state kinetics and intermediate identification. Initial velocity studies and the product inhibition studies with AMP and PPi strongly suggested ordered Bi Uni Uni Bi Ping-Pong Ter Ter system as the most probable steady state kinetic mechanism of malonyl-CoA synthetase. Michaelis constants were $0.17{\pm}0.04 {\mu}M,\;0.24{\pm}0.18 {\mu}M\;and\;0.045{\pm}0.26 {\mu}$M for ATP, malonate and CoA, respectively. The TLC analysis of the $^{32}P-labelled$ products in reaction mixture containing $[{\gamma}-^{32}P]$ ATP in the absence of CoA showed that PPi was produced after the sequential addition of ATP and malonate. Formation of malonyl-AMP, suggested as an intermediate in the kinetically deduced mechanism, was confirmed by the analysis of $^{31}P-NMR$ spectra of AMP product isolated from the $^{18}O$ transfer experiment using $[^{18}O]$malonate. Two resonances were observed, corresponding to AMP labelled with zero and one atom of $^{18}O$, indicating that one atom of $^{18}O$ transferred from $[^{18}O]$malonate to AMP through the formation of malonyl-AMP. Formation of malonyl-AMP was also confirmed through the TLC analysis of reaction mixture containing $[{\alpha}-^{32}P]$ATP. These results strongly support the ordered Bi Uni Uni Bi Ping-Pong Ter Ter mechanism deduced from the initial velocity and product inhibition studies.

• The Korea Journal of Herbology
• /
• v.32 no.6
• /
• pp.55-62
• /
• 2017

Objectives : This study aims to evaluate the effects of natural herb mixutre (NHM) on atopic dermatitis and skin regeneration using in vivo test. Methods : NHM was prepared with DW. 25% of NHM was applied to skin lesion, where atopic dermatitis was induced by DNCB in NC/Nga mice. The levels of cytokines (IL-4, IL-5, IL-6, IL-13, TNF-a, and $IFN-{\gamma}$), and IgE in serum were measured by Luminex. Immune cells (WBC, eosinophil, lymphocyte, and monocyte) in blood were counted by coulter counter. The gross investigation of atopic dermatitis index score test were performed during the NHM treatment period. Also, the histopathological change of dorsal skin was observed by H&E and M&T staining. Results : NHM showed the levels of IL-4, IL-5, IL-6, IL-13, IgE, WBC, eosinophil, lymphocyte, and monocyte in serum or blood were significantly decreased. On the contrary, the productions of FGF, and VEGF were increased in the serum. Also, atopic dermatitis index score in NHM-treated mice were observed in the similar levels to those of normal group. Histological examination demonstrated that NHM suppressed immune cell infiltration and thickening of epidermis, meanwhile the extraction induced collagen production in the dorsal skin. Conclusion : This study demonstrated that NHM is appeared to be effective on atopic dermatitis and skin regeneration efficacy based on the observations with hematologic, gross, and histologic examinations. Therefore, we suggest that NHM could be effectively used as an external therapeutics against atopic dermatitis and a consequence skin damage.