• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.6
• /
• pp.288-291
• /
• 2002

We developed a new RF indirect-heating LPE furnace. The thermal gradient of our newly developed furnace is less than that of direct heating, and is as gentle as that of the resistance-heating LPE furnace. With this new furnace, the heating and/or cooling is faster than that of the resistance-heating furnace. Impurity-doped YIG film was grown from a $PbO-B_{2}O_{3}$, based flux on a (111) GGG substrate. To study the effect of the impurities on the MSSW threshold power and the saturation response time, we used two microstrip lines to excite and propagate the MSSW at 1.9 GHz. The MSSW threshold power and saturation response time was found to be related to the $\Delta$H.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.103-105
• /
• 2012

With blast-furnace slag is a by-product generated when pig iron is produced. It has been used as the concrete admixture due to high reactivity. However, It causes low strength development during early age. In order to make up for this drawback, in this study, we evaluated compressive strength of mortar replaced with high volume blast-furnace slag. Experimental results, Compressive strength of mortar based on blast-furnace slag is affected by cement type, substitution rate of blast-furnace slag and pH after mixing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.40-45
• /
• 1999

This experimental study presents the strength properties of mortar using the blast-furnace slag sand. The mix disign of this study is based on the each three classes of unit water; (250, 275, 300)kg/㎥ and four classes of W/C; (45, 50, 55, 60)% and substitution rate(0, 25, 50, 75, 100)%. It gives following result. As W/C ratio increase, the strength is decrease. In case of mortar using air-cooled blast-furnace slag sand, the 3-days and 7-days compression strength is increase as substitution rate is higher. But in case of the mortar using the quenched blast-furnace slag sand, the compression strength is decrease as substitution rate is higher.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.210-211
• /
• 2014

Nowadays, as to reduce the emission volume of CO₂, blast furnace slag has been widely used to replacement of cement. Techniques about using industrial by-products has been extensively studied. For the previous study, blast furnace slag has been used with recycled fine aggregates. In thess study, considering about the different properties of blast furnace slag, as the change of blaine and chemical performances of blast furnace slag, the results of flowability and compressive strength has been analysed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.217-218
• /
• 2011

The advantages of blast-furnace slag concrete may include lower hydration heating velocity, restraint on concrete temperature increase, long-age strength improvement due to latent hydraulic reaction, improved water tightness, and repulsion to chemical erosion. These advantages contribute to the high quality of the blast-furnace slag concrete. However, the blast-furnace slag concrete has its limitations as well. These disadvantages may include retarded setting and elongated retention of mold due to the weak strength of early-age. Nevertheless, much research is currently under way to improve the aforementioned issues. To improve activity of blast furnace slag powder, alkaline irritants has been used. In this study, we analyze effect on activity fineness and rate of substitution of Alkali Activator toward activity.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.573-575
• /
• 2005

In the steel industry, a steel melting electric arc furnace is used to produce both carbon and alloy steels. Steel scrap which is charged into the furnace is heated by means of electric arc between graphite electrodes and the scrap. In this melting process, current is supplied to the furnace through HCC(high current cable) which connect the furnace and transformer. Four HCCs are assigned to each phase in our system to divide the current. Since a sudden cable breaking result in the shutdown of melting process, an aging detection of HCC is very important for both an improvement of productivity and cost reduction. In this paper, the aging of the HCC is estimated by using the current ratio between four HCCs.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.511-516
• /
• 2001

The flow characteristics in a hot mill reheating furnace is numerically simulated in this study. Navier-Stokes equations for conservation of mass, momentum, energy are solved and the standard $k-\varepsilon$ model, mixture fraction/PDF model are used for the turbulent reacting flow in the furnace. Radiation heat transfer is incorporated by the P-1 method with the absorption coefficient evaluated using WSGGM. First, simulation results are obtained for the total furnace region with existing protective dam, and then the calculations are carried out only for the preheating zone in the furnace. In that zone, additional center darn is built in order to control the flow behavior of the inlet air and the combustion gas.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.215-222
• /
• 1997

Flow experimental on not to be solid mortar which use Quenched Blast-furnace Slag as a fine aggregate was carried out for basic research data about fundamental study of application possibility of Quenched Blast-furnace Slag as a fine aggregate. It gives following result. The substitution rate is inversely proportional to Flow and C/S-rate same that. The relation with W/C-rate augment appear proportional : in case of C/S-rate, 1:3 increasing degree is a half of sand mortar that. Consequencely, Quenched Blast-furnace Slag motar is a counteraction to Flow in as same water content per unit. But suitable substitution rate and C/S-rate influence a little to the mortar consistency. And that reason, if C/S-rate and substitution rate will be regulated when we mix the mortar with quenched Blast-furnace Slag. that will be economic mixture.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.49-51
• /
• 2012

This study was conducted as a part of database construction for development of CO₂ assessment system for concrete to assess CO₂ emissions and analyze characteristics of blast furnace slag manufactured in Korea through life cycle assessment method. For this, life cycle CO₂ emissions assessment technique for construction materials was examined. The entire manufacturing process for blast furnace slag was analyzed on blast furnace slag manufacturer in Korea for application of assessment technique. Life cycle CO₂ assessment was performed on blast furnace slag after classifying assessment process into raw material production step, raw material transportation step and construction material manufacture step.

• 한국연소학회:학술대회논문집
• /
• 2012.04a
• /
• pp.41-42
• /
• 2012

Circulating fludized bed(CFB) furnace which can use a variety of low-grade fuels because of high heat capacity and good mixing characteristic in its furnace have turned out to be effective system. There is no many research to design CFB boiler in korea. thus, we feel necessity to research design method. So far accurate hydrodynamics and combustion mechanism information in CFB furnace has been lacked. Therefore, design method that derives design parameter is being made. so, this study is aimed to derive design parameters of CFB furnace from heat and mass balance by using existing plant data.