• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.3-9
• /
• 2002

Paper sludge ash was assured as material of a sort of pozzolan. For the reason of fluidity decrease caused by the strong absorption of paper stooge ash and the decrease of compressive strength in case of using over30% replacement by the weight of cement, paper sludge ash is not suitable for blending material. Therefore, it is necessary to find proper replacement ratios between paper sludge and blast furnace slag to insure compressive compensation and appropriate slump. Accordingly, as varied the blending ratios of paper sludge and blast furnace slag, testing mortar was made. This study was aimed to investigate the possibility of using blending replacement of paper sludge ash and blast furnace slag throughout compressive test, flow test, SEM(Scanning Eletron Microscope), MIP(Mercury Intrusion Porosity test), and TG-DTA(Thermal analysis).

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1830-1835
• /
• 2003

A novel index representing burden distribution form in the blast furnace is developed and index estimation model is built with an empirical modeling method to monitor inner condition of the furnace without expensive sensors. To find the best combination of index and modeling method, two candidates for the index and four modeling methods have been examined. Results have shown that 3-D index have more resolution in describing the distribution form than 1-D index and ANN model produces smallest RMSE due to nonlinearity between the indices and charging mode. Although ANN has shown the best prediction accuracy in this study, PLS can be a good alternative due to its advantages in generalization capability, consistency, simplicity and training time. The second best result of PLS in the prediction results supports this fact.

• Journal of the Korean Ceramic Society
• /
• v.53 no.4
• /
• pp.444-449
• /
• 2016

Industrial by-products generated by integrated iron and steel manufacture cause environmental pollution. The by-products contain not only iron element but also harmful substances. Therefore, in view of to waste recycling and environmental preservation, production of sponge iron using the by-product is considered an effective recycling method. In this study, reduction efficiency of pellets from blast furnace dust was measured. Metallization was found to be increased, as $C/Fe_{total}$ ratio and reaction time were increased. The pellets were formed into a globular shape, and calcined for 60 minutes at $1100^{\circ}C$ in an electric furnace. Phase changes were analyzed using an X-ray diffractometer. Microstructures of the pellets were observed by a scanning electron microscope.

• 한국방재학회:학술대회논문집
• /
• 2007.02a
• /
• pp.117-120
• /
• 2007

The main purpose of this paper is to introduce the early traffic opening-capable continuous multi-layer asphalt pavement maintenance method using electric arc furnace slag aggregate and emulsified asphalt to the actual construction sites. As well known, the previous surface treatment method of emulsified asphalt mixture have various shortcomings such as long work-time, traffic congestions, plastic deformation and poor evenness. Thus, the proposed method has enabled tile early traffic opening by utilizing the optimized emulsified asphalt after consideration of the climate and road conditions in Korea. The application of the electric furnace slag with $6\;{\sim}\;18\;mm$ thickness is helpful to become a environment-friendly construction method. And also, it has been improved enough to accommodate night-time works of mechanized construction activities for wearing course and control course.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.339-344
• /
• 2001

This study is to investigate properties of high strength.high flowing concrete using blast-furnace slag in temperature conditions of 5, 10, 15 and $20^{\circ}C$. The result of this study can be summarized as follows. 1) The use of blast-furnace slag leads to decrease of air content and increase of fluidity in the fresh concrete. 2) The early compressive strength of high strength.high flowing concrete containing blast-furnace slag is lower than the case with portland cement only. 3) The compressive strength development of incorporating in the concrete is poor at low temperature below about $15^{\circ}C$.

• Journal of the Korea Concrete Institute
• /
• v.12 no.2
• /
• pp.43-51
• /
• 2000

This study is to investigate for the frost resistance of high-flowing concrete using finely ground granulated blast-furnace slag with experimental parameters, such as type of binder, type of superplasticizer and method of curing. The resistance to freezing and thawing of high-flowing concrete by type of binder and superplasticizer is presented differently. Though the frost resistance of high-flowing concrete is satisfactory under standard condition, it is required that high-flowing concrete has entrained air like plain concrete. Because the critical spacing factor, being capacity of frost resistance, of high-flowing concrete is longer that of plain concrete, the frost resistance of high-flowing concrete, using finely ground granulated furnace blast slag, is superior to that of plain concrete.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.8 s.227
• /
• pp.937-944
• /
• 2004

An experimental study has been conducted to evaluate the effects of $CO_2$ on heat transfer from oxygen-enriched hydrogen flame. Experiments were performed on flames stabilized by a co-flow swirl burner, which was mounted on top of the furnace. Five different oxidizer compositions were prepared by replacing $N_2$ with $CO_2$. In a steady state, the total as well as radiative heat flux from the flame to the wall of furnace have been measured using a heat flux meter. Temperature distribution in furnace also has been measured and compared. By increasing $CO_2$ proportion in the oxidizer, the convection played a more significant role rather than radiation. Overall temperature in the furnace was seen to be decreased, while the total heat flux has increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.11
• /
• pp.1549-1554
• /
• 2000

A new method to determine the total heat exchange factor was proposed for the prediction of billet temperature in a reheating furnace. This method employed the squared of the difference between measured and predicted temperatures as an objective function. The real billet temperature in a walking beam type reheating furnace with 19.75m of its effective length was directly measured by thermocouples. The present method was validated by showing that the predicted billet temperature was in a good agreement with the measured one.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.408-411
• /
• 2005

Solar fuel production technology using high-temperature solar furnace was briefly reviewed in this paper. 'Hydrogen' which is known to be the most promising energy carrier in the near future is to be generated environment-friendly from non-carbon resources. Combination of solar furnace operated by concentrated solar energy and high-temperature thermal reactions could be one of the most efficient ways to fulfill this need eventually. Various reaction mechanisms are feasible within a wide spectrum of solar fuel production technology, but intensive research efforts in related key areas need to be taken for successful development and commercialization of the technology.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.613-618
• /
• 2002

Steel slag produced in steel making process is divided with electric arc furnace slag and converter slag. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, we treat electric arc furnace slag aggregate(EAFSA) for concrete before and after several aging process to reduce expansibility. The fundamental properties are measured, which are specific gravity, unit weight, abrasion value and immersion expansion ratio, as concrete aggregate. To understand the suitability of EAFSA for concrete, we made the concrete with EAFSA and then determined the strength and the volume change in EAFSA concrete. From the results EAFSA treated with steam aging process has potentiality for concrete aggregate.