• Journal of the Korean Magnetics Society
• /
• v.5 no.3
• /
• pp.165-170
• /
• 1995

NMR measurement has been studied for protons in pre-polarized flowing water by a separated detector working at high field far away from the measured field region where the transition of protons is occurred by the pertur-bation of RF energy. The conditions for NMR signal were optimized on the amplitude and frequency of modulation field, the RF field of detector, water speed, and RF field at the measured field region. The NMR signal with the full width of 320 nT at the half maximum in Lorentzian curve and with signal to noise ratio of 10.5 was measured in the range from a few ${\mu}T$ to mT, and its shape and amplitude were independent of the measured field intensity and its uniformity.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.3
• /
• pp.84-92
• /
• 2014

In this paper, a novel 5-axis hybrid-kinematic machine tool is introduced and the research results on accuracy improvement of the prototype machine tool are presented. The 5-axis hybrid machine tool is made up of a 3-DOF parallel manipulator and a 2-DOF serial one connected in series. The machine tool maintains high ratio of stiffness to mass due to the parallel structure and high orientation capability due to the serial-type wrist. In order to acquire high accuracy, the methodology of measuring the output shafts by additional sensors instead of using encoder outputs at the motor shafts is proposed. In the kinematic view point, the hybrid manipulator reduces to a serial one, if the passive joints in the U-P serial chain at the center of the parallel manipulator are directly measured by additional sensors. Using the method of successive screw displacements, the kinematic error model is derived. Since a ball-bar is less expensive than a full position measurement device and sufficiently accurate for calibration, the kinematic calibration method of using a ball-bar is presented. The effectiveness of the calibration method has been verified through the simulations. Finally, the calibration experiment shows that the position accuracy of the prototype machine tool has been improved from 153 to $86{\mu}m$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.94-94
• /
• 2018

무인자동차 및 전기자동차 등 전장부품 및 메인보드에서의 오염 방지와 전자파에 의한 신호 간섭 현상에 따른 기기의 오작동을 방지하고자 MWCNT의 clustering 및 tangling현상을 활용하여 self cleaning 기능을 갖는 super hydrophobic 표면과 high aspect ratio에 의한 percolation 현상을 활용하여 전자파 차폐를 위한 낮은 표면저항을 만족하는 복합 재료로 구성된 코팅에 관하여 연구하였다. 이를 위해 isopropyl alcohol(IPA)을 용매로 산처리 한 MWCNT와 무기바인더, 불소계 실란을 첨가하여 초음파 분산을 함으로써 코팅액을 제조하였다. 이를 full cone nozzle type, 흡상식 스프레이 조건으로 알루미늄 시편위에 스프레이 코팅 후 열경화 하여 접촉각측정기로 측정 결과 $160^{\circ}$이상의 초발수 표면과 Low Resistivity Meter로 표면저항을 측정한 결과 $10^3{\Omega}/cm^2$ 이하의 낮은 코팅막을 구현하였으며 내구성 실험을 위한 항온항습 장비로 $80^{\circ}C$의 내열테스트 및 80%와 $80^{\circ}C$조건하에서의 내습테스트 결과 표면에 이상 없음을 확인하였고 열전도율 측정을 위해 밀도 측정 결과 $2.68g/cm^3$, 비열 측정 결과 $0.85J/g^{\circ}C$가 열확산율 측정결과 $88.64mm^2/s$가 측정 되었으며 밀도, 비열, 열확산율을 곱한 값인 $201.9W/m{\cdot}K$의 열전도를 갖는 코팅막을 구현하였다.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.129-132
• /
• 2003

Yttria stabilized zirconia (YSZ) buffer layers were deposited by a metal organic chemical vapor deposition (MOCVD) technique using single liquid source for the application of YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) coated conductor. Y:Zr mole ratio was 0.2:0.8, and tetrahydrofuran (THF) was used as a solvent. The (100) single crystal MgO substrate was used for searching deposition condition. Bi-axially oriented CeO$_2$ and NiO films were fabricated on {100}〈001〉 Ni substrate by the same method and used as templates. At a constant working pressure of 10 Torr, the deposition temperatures (660~80$0^{\circ}C$) and oxygen flow rates (100~500 sccm) were changed to find the optimum deposition condition. The best (100) oriented YSZ film on MgO was obtained at 74$0^{\circ}C$ and $O_2$ flow rate of 300 sccm. For YSZ buffer layer with this deposition condition on CeO$_2$/Ni template, full width half maximum (FWHM) values of the in-plane and out-of-plane alignments were 10.6$^{\circ}$ and 9.8$^{\circ}$, respectively. The SEM image of YSZ film on CeO$_2$/Ni showed surface morphologies without microcrack.k.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.3
• /
• pp.7-9
• /
• 2014

Single-crystal like $MgB_2$ thin film was grown on (000l) $Al_2O_3$ substrate by using hybrid physical-chemical vapor deposition (HPCVD) system. Single crystal properties were studied by X-ray diffraction (XRD) and the full width at half maximum (FWHM) of the (0001) $MgB_2$ peak is $15^{\circ}$, which is very close to that has been reported for $MgB_2$ single-crystal. It indicates that the crystalline quality of thin film is good. Temperature dependence on resistivity was investigated by physical property measurement system (PPMS) in various applied fields from 0 to 9 T. The upper critical field ($H_{c2}$) and irreversibility field ($H_{irr}$) were determined from PPMS data, and the estimated values are comparable with that of $MgB_2$ single-crystals. The thin film shows a high critical temperature ($T_c$) of 40.4 K with a sharp superconducting transition width of 0.2 K, and a high residual resistivity ratio (RRR=21), it reflects that $MgB_2$ thin film has a pure phase structure.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.110-118
• /
• 2002

Organic thin film transitors(OTFT) are of interest for use in broad area electronic applications. And recently organic electroluminescent devices(OELD) have been intensively investigated for using in full-color flat-panel display. We have fabricated inverted-staggered structure OTFTs at lower temperature using the fused-ring polycyclic aromatic hydrocarbon pentacene as the active eletronic material and photoacryl as the organic gate insulator. The field effect mobility is 0.039∼0.17 ㎠/Vs, on-off current ratio is 10$\^$6/, and threshold voltage is -7V. And here we report the study of driving emitting, Ir(ppy)$_3$, phosphorescent OELD with all organic thin film transistor and investigated its electrical characteristics. The OELD with a structure of ITO/TPD/8% Ir(ooy)$_3$ doped in BCP/BCP/Alq$_3$/Li:Al/Al and OTFT with a structure of inverted-stagged Al(gate electrode)/photoacry(gate insulator)/pentacene(p-type organic semiconductor)/ Au(source-drain electrode) were fabricated on the ITP patterned glass substrate. The electrical characteristics are turn-on voltage of -10V, and maximum luminance of about 90 cd/㎡. Device characteristics were quite different with that of only OELD.

• Steel and Composite Structures
• /
• v.19 no.3
• /
• pp.735-757
• /
• 2015

Composite bonding steel plate (CBSP) is a newly developed type of structure strengthened technique applicable to the existing RC beam. This composite structure is applicable to strengthening the existing beam bearing high load. The strengthened beam consists of two layers of epoxy bonding prestressed steel plates and the RC beam sandwiched in between. The bonding enclosed and prestressed U-shaped steel jackets are applied at the beam sides. This technique is adopted in case of structures with high longitudinal reinforcing bar ratio and impracticable unloading. The prestress can be generated on the strengthening steel plates and jackets by using the CBSP technique before loading. The test results of full-scale CBSP strengthened beams show that the strength and stiffness are enhanced without reduction of their ductility. It is demonstrated that the strain hysteresis effect can be effectively overcome after prestressing on the steel plates by using such technique. The applied plates and jackets can jointly behave together with the existing beam under the action of epoxy bonding and the mechanical anchorage of the steel jackets. The simplified formulas are proposed to calculate the prestress and the ultimate capacities of strengthened beams. The accuracy of formulas was verified with the experimental results.

• Proceedings of the Safety Management and Science Conference
• /
• 2002.11a
• /
• pp.227-232
• /
• 2002

Enormous flocks by the reduced life cycle of products caused by the technological innovation if later 20 century, development of new materials and diversified demands of customers appeared as the pressing element causing the trouble in management of companies, and when considering the logistic costs that are imposed to companies in terms of function, the costs related to the stock topped the list of costs, followed by the transportation ones, and for pallet pool system, inventory of stocks is very difficult by the number of companies. Reducing the logistic cost may be accomplished by numbers of logistic management methods, but the most fundamental and essential one is the accomplishment of the consistent pallet system that is the core of unit load system, and the purpose of consistent pallet system is the treatment of logistic functions such as transportation, storage and unloading with consistent pallet system, and increasing the turnover ratio is required for the improvement of the system. As the turnover ratios is increased, more pallets will be used so, numbers of empty pallets will be increased accordingly by returning the pallet. Therefore, in this study, we will establish the effective stock management system by comparing with the other existing stock management system after looking at the concept and examples of pallet full system in order to resolved this kind of problem.

• 보존과학연구
• /
• s.27
• /
• pp.43-61
• /
• 2006

In this study stone heritages of 533 which is to be investigated through the five years for national treasures and treasures from 2001 to 2005 have been analyzed by statistics for types of stone heritages and rocks, level of alteration in order to make full use of guiding principle in conservation management of stone heritages. The ratio of stone pagoda as a percentage of 34.5% in the stone heritages much higher than others and that is composed of granite(83.0%) in the igneous rock. In the weathering index of surface, a 37.5% of the national treasures were classified with the level 4 and46.3% of the treasure were the level 3 according to state. The present condition of organism distribution take up 30.6% for the level 3 and 22.1% for level 1. In structural stability index, a 40.6%of the national treasures and a 54.2% of treasure were ranked level 3.

• Journal of Korean Society on Water Environment
• /
• v.28 no.5
• /
• pp.663-668
• /
• 2012

The feasibility of enhancing biological nutrient removal from an industrial wastewater was tested with food waste leachate and sugar liquid waste as external carbon sources. Long term influences of adding external carbon sources were investigated to see how the biological nutrient removal process worked in terms of the removal efficiency. The addition of the external carbons led to a significant improvement in the removal efficiency of nutrients: from 49% to approximately 76% for nitrogen and from 64% to around 80% for phosphorus. Approximately, 20% of the removal nitrogen was synthesized into biomass, while the remaining 80% was denitrified. Though the addition of external carbon sources improved nutrient removal, it also increased the waste sludge production substantially. The optimal observed BOD/TN ratio, based on nitrogen removal and sludge production, was around 4.0 in this study.