• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.1
• /
• pp.1-9
• /
• 2007

The performance of the small scale cyclone incinerate system (100kg/hr) to process the sewage sludge containing high moisture is evaluated. The incinerate system design is based on properties of the domestic sewage sludge. The combustion characteristics of the incinerate system is tested and analyzed with the various operation conditions of the moisture level, the sludge feed rate and the auxiliary fuel feed rate. The pressure loss of the whole system is appeared relatively small of 700mmAq under the normal operating condition and the temperature distribution of the incinerator internal combustion is maintained less than 1000C. Auxiliary fuel of 4.7 1/hr is required to incinerate 100kg sludge which include 87% moisture. Because the inside temperature of the incinerator is maintained less than $1000^{\circ}C$, it is predicted that the most NOx measured is produced not from the heat during the combustion process but from the oxidation of the N ingredient in the sludge. From the component analysis of ash, the organic matter is not entirely detected. Accordingly, it is estimated that the complete combustion has been accomplished in the incinerator.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.1-6
• /
• 2014

Upgrading technology has been studied for efficient utilization of low rank coal. Spray coating of heavy oil was applied on the upgrading process in order to stabilize low rank coal against spontaneous combustion. Low rank coal, which contains more than 30wt% of moisture, was upgraded to high calorific coal and stabilized by spray coating of heavy oil. It was identified that spray coating of heavy oil after drying coal is the optimum procedure of upgrading low rank coal. The experimental results show that more than 2wt% of heavy oil should be adsorbed on the coal in order to stabilize sufficiently for spontaneous combustion.

• Journal of Aerospace System Engineering
• /
• v.18 no.1
• /
• pp.79-87
• /
• 2024

The Korean launch vehicle (KSLV-II) has used commercial aviation jet fuel, Jet A-1. Fuel specifications were introduced from Jet A-1 specifications. However, specifications and inspection methods of moisture and particulate matters were changed digitally for convenience and accuracy. To control fuel quality, a fuel management system was established to determine suitability by inspecting it at each stage of warehousing, storage, and application. An analysis room was then established at the Naro Space Center. The possibility of fuel mixing was blocked by warehousing inspection. Long-term component changes were then observed by storage inspection. Finally, suitability of the engine test or the launch vehicle test was determined through application inspection. Long-term analysis verified that the space center's fuel oil storage method was appropriate and that the quality management system was able to handle hundreds of engine tests and several flight tests.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.12
• /
• pp.1347-1351
• /
• 2006

It was tried to utilize organic waste sludge from wastewater treatment plant as a starting material to produce a solid fuel by vacuum flying. The effects of decompression levels, frying time and temperature on the calorific value and moisture of vacuum fried sludge were systematically investigated. Dewatered raw sludge used in this study had a moisture of 81.1% and calorific value of 2,930 kcal/kg. Based on the experimental observation, it was identified that the decompression level and frying time have the greatest influence on the calorific value of vacuum fried sludge. Moistures of the fried sludge at $180^{\circ}C$ for 25 min in 760 mmHg, 684 mmHg and 630 mmHg were 32.4%, 14.2% and 11.6%, respectively. Calorific values of the vacuum fried sludge at $140^{\circ}C$ for 15 min and 25 min were 5,400 kcal/kg and 5,540 kcal/kg in 684 mmHg and 5,520 kcal/kg and 5,660 kcal/kg in 630 mmHg, respectively.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.4
• /
• pp.83-90
• /
• 2019

In this study, the characteristics of the SRF (Solid Refuse Fuel) prepared by blending each of the additives (citrus peel, waste wood, coal) in the heavy oil fly ash, evaluating the heavy oil fly ash recyclability. Recycling SRFs were fabricated by pellet extruding method after blending the heavy oil fly ash and additives based on 30% moisture content. As a result, the formability of the SRFs was excellent under condition of blending heavy oil fly ash with coal or citrus peel and the highest calorific value was 4,274 kcal/kg at heavy oil fly ash mixed with coal. Therefore, the formability and calorific value were improved when the heavy oil fly ash was mixed with coal(20 wt%) at 30% moisture content. From these results, the applicability of SRFs with additives was confirmed by using the heavy oil fly ash from J thermal power plant.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.10
• /
• pp.901-909
• /
• 2013

Owing to the Increasing use of fossil fuels, worldwide concerns over environmental pollution are increasing. As a solution, ligneous biomass has emerged as a promising alternative fuel in recent times. Therefore, in this study, a moisture evaporation model that largely influences the energy density and efficiency of ligneous biomass is studied using a numerical approach. Furthermore, the thermal characteristics are analyzed in terms of torrefaction temperature and moisture fractions in the wood, and the type of wood species. The results show that the temperature and moisture fractions of wood decrease with an increase in the torrefaction temperature. In particular, when the torrefaction temperature is lower than 423K, there were little changes in the moisture fraction in the wood. Furthermore, it was found that charcoal is produced more slowly as the moisture fraction in the wood increases.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.2
• /
• pp.142-150
• /
• 2009

This paper presents bio-ethanol production from fruit wastes as it possibly alternate fossil fuel in the future. To illustrate the component ratio in exocarps of fruit wastes such as pears, apples, and persimmons, the amount of moisture, lignin, $\alpha$, $\beta$, $\gamma$-cellulose, and ash content were respectively examined by the ingredient analysis. Also, the amount of the glucose obtained from the enzyme hydrolysis using the axocarps was investigated. It was found in our results that the energy efficient process requires different temperature conditions for the saccharification step($50^{\circ}C$ and the fermentation step($30^{\circ}C$ in ethanol synthesis.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.11
• /
• pp.1627-1633
• /
• 2012

This study was to evaluate the feasibility of recycling the solids separated from swine wastewater treatment process as a fuel source for heat production and to provide a data set on the gas emissions and combustion properties. Also, in this study, the heavy metals in ash content were analyzed for its possible use as a fertilizer. Proximate analysis of the solid recovered from the swine wastewater after flocculation with organic polymer showed high calorific (5,330.50 kcal/kg) and low moisture (15.38%) content, indicating that the solid separated from swine wastewater can be used as an alternative fuel source. CO and NOx emissions were found to increase with increasing temperature. Combustion efficiency of the solids was found to be stable (95 to 98%) with varied temperatures. Thermogravimetry (TG) and differential thermal analysis (DTA) showed five thermal effects (four exothermic and one endothermic), and these effects were distinguished in three stages, water evaporation, heterogeneous combustion of hydrocarbons and decomposition reaction. Based on the calorific value and combustion stability results, solid separated from swine manure can be used as an alternative source of fuel, however further research is still warranted regarding regulation of CO and NOx emissions. Furthermore, the heavy metal content in ash was below the legal limits required for its usage as fertilizer.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.4
• /
• pp.403-409
• /
• 2017

For dry storage of the spent nuclear fuel (SNF) stored in the storage pool of a nuclear power plant, essentially all moisture must be removed to prevent corrosion of the assembly and canister internals and/or degradation of fuel cladding integrity after SNF canister loading operation. R&D work is now in progress on a forced gas drying system that can be used to remove residual water in canisters. In this work, preliminary design is performed to manufacture the forced gas drying system. This process includes a case study of dry methods for canister moisture removal, relative codes and standards, confirmation of adequate dryness, needs analysis at plant sites, and characteristics of SNF stored in pools. Through this preliminary design work, we obtained a conceptual flow diagram and preliminary P&ID of the forced gas drying system. The results of this study can be used to determine details of the design to manufacture the forced gas drying system.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.3
• /
• pp.367-373
• /
• 2011

This research is a basic researching process for producing solid fuel that mixing paper sludge and Heat Transfer Medium Oil. Under the presence of Heat Transfer Medium Oil, paper sludge is heated and dried with home appliance microwave for comparing drying efficiency and energy efficiency of different types of drying method. As a result, Heat Transfer Medium Oil and paper mixing case of drying method, OMD, is the most efficient way to shorten the time for evaporating moisture in the paper sludge. In addition, heat transfer effect and density is increased with adding Heat Transfer Medium Oil by microwave. Future more, OMD's energy cost for evaporating whole moisture is 78% cheaper than MD. Also, OMD process shows the best energy efficiency with comparing other process. Evaporation rate of paper sludge evaporation process with microwave is 11.66% increased by adding Heat Transfer Medium Oil 150g. Preheating Heat Transfer Medium Oil or improving different ways injecting Heat Transfer Medium Oil is a good way to increase a rate of initiative moisture evaporation process.