• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.93-96
• /
• 2004

In the case of the front door of the apartment, which functions as an entrance, the study about noise has been less active than corridor type plane in the past, since stair room type plane was generalized. Hence, this study shows the survey about residents' thoughts of noise transmission through the front door, and after researching sound insulation of the present apartments, we figured out what the problem is. Moreover, we did an efficiency test as developing the front door, which increases sound insulation. As a result, it turned out that residents think that the noise transmission through the front door is as serious as floor impact noise, and also, the efficiency of the front door is as poor as STC 22-30. Therefore, in the developed front door, we should improve the efficiency to the level of STCSS. It will be a good way preparing for a demand of residents.

• 한국산학기술학회논문지
• /
• 제11권3호
• /
• pp.821-826
• /
• 2010

도어락 스위치(Door-lock switch)는 드럼세탁기, 식기 세척기 등 회전이나 열이 발생되어 작동 할 때 임의로 열지 못하도록 하는 가전제품에 쓰이는 도어 안전잠금장치로 드럼세탁기에서는 없어서는 안 되는 중요한 부품 중의 하나이다. 드럼 세탁기 도어는 소비자가 사용 할 때 느낌을 가지는 부분으로 항상 안전성과 동시에 감성이 뒤따르는 부품이기도 하다. 본 논문은 드럼세탁기의 도어에 감성과 관련된 요소들을 조사하였으며, 도어락 스위치의 기구적인 구조들을 파악한 뒤 드럼세탁기에 장착하였을 때 열림력, 닫힘력을 측정할 수 있는 지그와 소프트웨어를 제작하고 측정한 힘의 그래프를 분석하여 사용자에 의해 평가한 후, 드럼세탁기 도어락 스위치의 구조에 따른 감성에 차이점을 찾아보고 시스템의 사용을 검증하였다.

• KIEAE Journal
• /
• 제10권3호
• /
• pp.51-56
• /
• 2010

The sound insulation performance is one of the important factor that determined the amenity of housing life in residential building. Especially, Apartment house represents a korea habitation. So the importance of privacy and noise problems between habitable rooms are emphasized in these habitation. This study investigates and find a problem of sound insulation performance of partition wall of the apartment house in current state. The measurements were carried out in apartment house with and without a stair hall. And the measurements also carried out in current state and installing a sound absorbing material in receiving room and changing a front door and installing a inner door. In spite of the same partition wall, difference results were showed according to the stair hall. It is appeared that sound insulation performance without stair hall is 6-7dB(Dw) higher than that with stair hall. In case of without stair hall, sound insulation performance is Dw 49 for single number quantity for airbone sound. And In case of changing a front door and installing a inner door sound insulation performance is Dw 57 for single number quantity for airbone sound. The Results of measuring on the changes a front door and installed a inner door indicated that the flanking sound through front door influenced the sound insulation performance.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.53.1-56
• /
• 1999

Using a new dynamic-explicity program SAIT_STAMP the analysis of forming a front door panel is presented. The analysis consists of 7 processes including drawing trimming flanging and springback. From the analysis results it is shown that adaptive refinement scheme and robust trimming algorithm enable SAIT_STAMP to simulate the multi-stage forming of automotive parts with large and complex geometry.

• 한국실내디자인학회논문집
• /
• 제17권1호
• /
• pp.155-161
• /
• 2008

In Seowon architecture, there are four kinds of space conditions according to the site plan and the figure of education area. The education area has three main buildings such as Kangdang, Dongjae, Seojae. In case Kangdan locates in front of Dongjae and Seojae(so called Junkangdang-Hoojaesa), but in another case Dongjae and Seojae locates in front of Kangdang(so called Junjaesa-Hookangdang). This four space conditions affect to decide the floor plan and the window & door system of Kangdang. In Junjaesa-Hookangdang type, the front and rear wall has more open system than in Junkangdang-Hoojaesa type. In Junjaesa-Hookangdang type the direction of Kangdang is absolutely open to front education area, but in Junkangdang-Hoojaesa type the direction of Kangdang is absolutely open to rear education area. These floor plan aims at making up education area more closely. In window & door system the rear parts of Junjaesa-Hookangdang type have generally opaque system such as Golpanmoon or Panjangmoon, but Junkangdang-Hoojaesa type breaks this rule in order to emphasize front facade of building.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.23-24
• /
• 2021

Since 2011, apartment houses account for about 41% of the fires in residential facilities for the past 10 years. Fire-resistant performance of fire doors is becoming more important to prevent the spread of fire in apartment houses. This research analyzed the structure of fire door through each 10 DB based on the quality inspection report of Continuous Acquisition & Life-cycle Support(CALS) from 2016 to 2020, which passed the fire performance test based on the laws and notices of domestic fire door. Therefore, based on the results of the analysis of DB in the future, we will conduct a study on structural improvement and addition for fireproof performance improvement of fire door.

• 대한방사선기술학회지:방사선기술과학
• /
• 제42권6호
• /
• pp.477-482
• /
• 2019

Recently, due to the increased use of medical radiation, the radiation exposure of radiation workers should be considered as well as medical exposure of patients. And it is recommended to close the door during radiography. however, In this study, when the door was inevitably opened for radiography, the proposed method was to install the shield as a method of reducing the exposure dose. And its efficiency was analyzed. In simple chest radiography, the measurement point was changed according to the measurement location. Dose rate were measured 10 times for each condition using a dosimeter. And the average value was derived. Using this, the change of dose according to the opening and closing of the door and the installation of the shield was analyzed. Using this, we compared and analyzed the dose change according to the door opening and closing and the installation of the shield, and significance was verified through the SPSS ver. 24. Depending on whether the door was opened or closed, 11,215.35%, 159.0%, 101.9% increased in front of the door in the consol room, behind the wall and behind the lead glass. Depending on the installing of the shield, the 49.2%, 29.6%, 19.9%, 30.6% decrease in front of the door in the examination and consol room, behind the wall and lead glass. In addition, statistical analysis was showed that there were significant differences in both the results according to whether the door was opened or closed and shielding(p<.05). Close the door during radiography. However, when the door should be opened, it was confirmed that the dose rate were reduced by installing the shield. Therefore, to optimize radiation protection, it is recommended to install shields when opening the door.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 2004년도 추계학술대회
• /
• pp.32-32
• /
• 2004

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.31-36
• /
• 1997

Various methods of finite element modeling for welded part are examined and the stamping simulation of automotive body is presented by using the explicit finite element code PAM-STAMPTM. The process of stamping simulation is suggested step by step, and then the gravity, binder wrap, forming, trimming and springback of front door inner are analyzed. It shows good agreements with real product in the aspects of deformed shape and failure area. The door inner with laser-tailor welded blank is simulated, in which deformed shape, movement of welde line and formability are predicted.

• 대한기계학회논문집A
• /
• 제30권8호
• /
• pp.1016-1023
• /
• 2006

When one opens the door of a microwave oven during its operation, twisting deformation of the door occurs, which may cause leakage of microwave through the gap between the door and the front plate. A numerical optimization is implemented to minimize the gap by maximizing twisting stiffness of the door of the oven. Design variables are deformed, which describe the shape of the bead in the horizontal and vertical flanges of the door frame. To minimize the twisting deformation, Two optimal design problems to find shapes of the bead in the flange are established. The problems are solved by a numerical optimization technique, their results being evaluated.