• Tribology and Lubricants
• /
• v.18 no.4
• /
• pp.255-259
• /
• 2002

The tribological properties of eight different liquid crystals were investigated in a concentrated point contact device and a ball-on-flat contact. For comparison, the same tests were also performed with commercial greases and the corresponding base oils. Under the fully flooded conditions studied, liquid crystals in a concentrated point contact showed lower friction than commercial greases and greater film thickness dependence on rolling speed than grease base oils or greases. Test results also showed that the film thickness and friction were little influenced by the composition of the examined liquid crystals.

• Journal of KSNVE
• /
• v.7 no.3
• /
• pp.499-509
• /
• 1997

During the process of oxide removal from work rolls in sheet metal manufacture, filamentary brushes frequently exhibit a bouncing or chatter behavior. The dynamics of this phenomenon is investigated through the development of expressions for the non-linear contact stiffness between the brush and the roll. With formulation of simple structural models, the time responses in the presence and absence of friction under random excitation are investigated. Possible solutions for the minimization or avoidance of this bouncing or chatter problem are also suggested.

• Structural Engineering and Mechanics
• /
• v.3 no.3
• /
• pp.289-297
• /
• 1995

A finite element algorithm for consideration of contact constraints is presented. It is characterized by introducing the geometric constraints, resulting from contact conditions, directly into the algebraic system of equations for the incremental displacements of an incremental iterative solution procedure. The usefulness of the proposed algorithm for efficient solutions of contact problems involving large displacements and large strains is demonstrated in the numerical investigation.

• Journal of the Ergonomics Society of Korea
• /
• v.25 no.1
• /
• pp.43-49
• /
• 2006

A laboratory study was conducted to evaluate if two different age groups(young vs. old) had differences in walking velocity and heel contact velocity and, furthermore, if these gait characteristics could adversely influence initial friction demand characteristics(i.e. RCOF) and the likelihood of slip-initiation. Twenty eight(14 younger and 14 older adults) participated in the study. While wearing a safety harness, all participants walked at their preferred gait speed for approximately 20 minutes on the linear walking track(1.5m× 20m) consisting of two floor-mounted forced plates. During subsequent 20 cameras, respectively. The results indicated that older adults walked slower(i.e., slower whole body center-of-mass velocity), exhibited lower heel contact velocity, and produced lower initial friction demand characteristics (i.e. RCOF) in comparison to younger adults. However, ANCOVA indicated that the diferences in heel contact velocity between the two age groups were due to the effects of walking velocity. The bivariate analysis further suggested that walking velocity was correlated to RCOF and heel contact velocity, while heel contact velocity was not found to be correlated to RCOF. In conclusion, could be a better indicator for predicting initial friction demand characteristics(i.e. RCOF) not hel contact velocity.

• International Journal of Automotive Technology
• /
• v.4 no.4
• /
• pp.165-172
• /
• 2003

This article deals with the spin loss analysis of friction drive CVTs, especially for the cases of S-CVT and SS-CVT. There are two main sources of power loss resulting from slippage in the friction drive CVT, spin and slip loss. Spin loss, which is also a main design issue in traction drives, results from the elastic contact deformation of rotating bodies having different rotational velocities. The structure and operating principles of the S-CVT and SS-CVT are first reviewed briefly. And to analyze the losses resulting from slippage, we reviewed previous analyses of the friction mechanism. A modified classical friction model is proposed, which describes the friction behavior including Stribeck (i.e., pre-sliding) effect. It is also performed an in-depth study for the velocity fields generated at the contact regions along with a Hertzian analysis of deflection. Hertzian results were employed to construct the geometric parameters and normal pressure distributions of the contact surface with respect to elastic and plastic deformations. With analytic formulations of the relative velocity field, deflection, and friction mechanism of the S-CVT and SS-CVT, quantitative analyses of spin loss for each case are carried out. As a result, explicit models of spin loss were developed.

• Tribology and Lubricants
• /
• v.20 no.2
• /
• pp.51-57
• /
• 2004

Micro/nano adhesion and friction properties of mixed self-assembled monolayer (SAM) with different chain length for MEMS application were experimentally studied. Many kinds of SAM having different spacer chains(C6, C10 and C18) and their mixtures (1:1) were deposited onto Si-wafer, where the deposited SAM resulted in the hydrophobic nature. The adhesion and friction properties between tip and SAM surfaces under nano scale applied load were measured using an atomic force microscope (AFM) and under micro scale applied load were measured using ball-on-flat type micro-tribotester. Surface roughness and water contact angles were measured with SPM (scanning probe microscope) and contact anglemeter. Results showed that water contact angles of mixed SAMs were similar to those of pure SAMs. The morphology of coating surface was roughened as mixing of SAM. Nano adhesion and nano friction decreased as increasing of the spacer chain length and mixing of SAM. Micro friction was decreased as increasing of the spacer chain length, but micro friction of mixed SAM showed the value between pure SAMs. Nano adhesion and friction mechanism of mixed SAM was proposed in a view of stiffness of spacer chain modified chemically and topographically.

• Journal of the Korean Society of Safety
• /
• v.19 no.1
• /
• pp.12-17
• /
• 2004

By using an experimental approach recently developed to determine the torque-tension relationship for bearing frictional characteristics of several typical bolted joints were studied. The experimental approach allows the direct determination of the bearing friction between the nut and its bearing surface. Detailed friction studies were made on the influences of the size and shape of the hole, the use of a slot in a bolted joint, contact area and position, and other factors such as turning speed, coating, and the use of wax on the bearing surface. The contact area and position of the washer have a marginal effect on the bearing friction. The organic coating on the nuts reduces the bearing friction significantly. Nuts with organic coating over a washer with zinc finish provide the smallest and the most consistent bearing friction. The results from the experimental investigation will be helpful for the better design of bolted joints bearing friction. The results from the experimental investigation Will be helpful for the better design of bolted joints.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.26-34
• /
• 1998

This paper presents a high-speed performance analysis of ball bearings with ceramic balls under thrust loads. The sliding velocity profiles between a ball and raceways were obtained by the 3-D quasi-dynamic equations of motion including both centrifugal force and gyroscopic moment derived by vector matrix algebra. The friction at the contact areas was obtained by the Bair-Winer's non-Newtonian rheological model and the Hamrock-Dowson's central film thickness in EHL analysis. The nonlinear equations were solved by the Newton-Raphson method and the underrelaxation iterative method. The friction torques and ball behaviors with various loads, ball materials, and contact angles were predicted by this model. It was shown that the friction torque was sensitive to thrust load and contact angle, and that the friction torque and the pitch angle of the bearing with ceramic balls are smaller than those of the bearing with steel balls.

• Tribology and Lubricants
• /
• v.11 no.3
• /
• pp.48-53
• /
• 1995

In this paper, the friction characteristics of contact region between vane tip and camring is studied using a modeled experimental device. The contact region is under the influence of variable loads with the amplitude of hundreds of Newton and frequency of tens of Hz. The condition of lubrication between vane and disk is modeled after the actual condition between vane and camring. The coefficient of friction is obtained by measuring the frictional forces in the contact region between camring and vane. The friction characteristics of the actual oil hydraulic vane pump is estimated on the basis of coefficient of friction. The analysis of frictional characteristics shows us that the lubrication condition of vane tip is that of transition regime between hydrodynamic lubrication and mixed lubrication.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.33-40
• /
• 1997

This study was undertaken to investigate tribology characteristics of the alumina ceramics($Al_2O_3$) for the vauiation of ambient condition such as air and distilled water. The results obtained were as follows. As the sliding speed increases, the friction coefficient in the air decreased due to the reduction of sheafing stress caused by the heat accumulation of contact interface. And the friction coefficient in the distilled water decreased due to an activation of the tribochemical reaction. As the contact load increases, the friction coefficient is small in the air due to temperature rise of the contact interface. However, at the low speed side in the distilled water, the friction coefficient holds a large value due to decrease of the tribochemical reaction. The friction surface of ceramics can be protected in the air by the influence of the oxides tansfered from STB2 and also in the distilled water by the influence of the corrosive productive hydroxides.