• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.3
• /
• pp.87-94
• /
• 2007

A structural dynamic analysis can be divided into a time domain analysis and a frequency domain analysis. The time domain analysis makes use of a direct integration method or a mode superposition method and the frequency domain analysis applies a DFT method. Generally the DFT method is more effective method in case of calculating response of periodic excitation. But in case of transient excitation exact solution can not be acquired. So, by modifying the response or increasing the period accuracy of solution can be enhanced. Accordingly this study analyzed dynamic responses of structures under aperiodic moving load in time domain and frequence domain. Consequently it is concluded that exact solution would be get enough using DFT method by increasing the duration of free vibration or modifying the dynamic response.

• Advances in concrete construction
• /
• v.17 no.3
• /
• pp.151-158
• /
• 2024

The calculation of the natural frequencies versus Young's modulus of carbon nanotubes with modified continuum shell is the subject of current research. When designing these tubes, it is important to understand their frequencies because excessive vibrations might cause fatigue. These tubes are designed and built to meet specific needs and have been suitably modified to investigate their vibratory response. There are numerous uses for carbon nanotube free vibration analysis in the mechanical sciences. The fundamental frequency with Young's modulus for clamped-free and simply supported end conditions, which is connected to the carbon nanotubes, is calculated theoretically for chiral single carbon nanotubes. When Young's modulus rises, so does the frequency curve pattern. Young's modulus influences the single-walled carbon nanotube's dynamic response by simulating it as a modified continuum shell. The Young's modulus of chiral tube and the value of frequency increased as the chiral tube's index increased. The results are checked against past studies to ensure the problem's validity and are determined to be accurate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.299-304
• /
• 1993

A 1/4 car model(2 DOF system) is employed to evaluate the performance included a quadratic cost functional in frequency domain. The design procedure of feedback control to optimize the performance index results in a modified Linear-Quadratic-Gaussian problem and cultivates a quite simple control algorithm. Computer simulation result is shown that the LQG method using frequency shaped performance index is outstanding in ride comfort and its response converges to the steady state very rapidly in comparison with the known passive suspension, classical design methods LQR/ and LQG.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.35-42
• /
• 1995

In this paper the driving-condition-dependent optical transmission characteristics of an STN LCD are studied. The optical transmission properties are measured for the applied voltage waveform is varied. Also, the optimum ranges of the M signal frequency and the frame frequency are investigated. An LCD is modeled by the equivalent circuit to study the effect of the parameter variation on the frequency response.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.360-362
• /
• 2004

In this paper, as the preceding research for development of intelligent electronic device for digital based substation automation system, we tried to select the most suitable digital filter by comparison of frequency response characteristic, performance of wanted frequency component extraction.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.30-33
• /
• 1991

The natural frequency of an one-link flexible robot manipulator may be varied due to many kinds of causes and this natural frequency is regarded as the uncertain element. Utilizing measured state the robust controller is designed for bounding every system response within a certain neighborhood of the zero state.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.5
• /
• pp.77-84
• /
• 1992

In the most of acoustic system with low flow rate and low pressure level, one-dimensional, linear modeling techniques are used very well. At low frequency, the tube is modeled as inertia element and cavity as capacitance element, and to extend the range of frequency normal mode oscillators are represented. Bond graph modelling techniques are proposed to predict TL (Transmission Loss) and time response which is impossible by transfer matrix in muffler system. A simple acoustic filter which consists of several tubes and cawities is analyzed in both time and frequency domain.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.63-64
• /
• 2006

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.385-388
• /
• 2003

In this paper, a D-Latch is replaced by a memory cell on the proposed PFD to improve response tine by reducing reset me. The PFD has been simulated using HSPICE with a Hynix 0.35um CMOS process to prove the performance improvement.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1993.10a
• /
• pp.71-75
• /
• 1993

The Modeling analysis and design of a high frequency LC-type series and LLCC-type parallel resonant converter oprating in the continous conduction is presented. The state-plane diagram representation of the converter response gives and good insight into the converter operation. A set of characterisric frequency are plotted which design parameters can be obtained.