• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제17권9호
• /
• pp.401-406
• /
• 2016

When measuring live cable faults and their location based on reflectometry, a coupler is placed between the cable and the test system. This coupler prevents damage to the test circuits by indirectly measuring the live voltage of the cable using reflectometry. It also provides a coupling path that allows the transmission and receive signal to pass into the cable. In this study, we design and construct a contact coupler to locate faults in both dead and live cables using reflectometry. The proposed coupler is of the inductive coupling type and is constructed after the calculation of the signal transmission loss by simulation. The performance of the developed coupler is tested by measuring the transmission loss and frequency flatness. The results showed that the transmission signal loss is less than -1.98dB in the frequency bandwidth above 1 Mhz. The reflectometry system was designed based on sequence time domain reflectometry (STDR) and spread spectrum time domain reflectometry (SSTDR) in order to apply it to the detection of faults and their location in live cables and tests on live cables were performed. The test results showed that the proposed coupler can be used in a reflectometry system for live cable fault detection.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1664-1667
• /
• 2003

Aperture-coupled microstrip antenna is one type of microstrip antennas. This type of antenna has bandwidth wider than simple microstrip antenna. Herein, we use two substrates, that have the same dielectric constant 2.47 (PTFE-quartz) in which upper substrate is a rectangular patch. The microstrip patch is fed by a microstrip line which is printed on lower substrate, through an aperture or slot in the common ground plane of patch and microstrip feed. This antenna is analyzed by using Finite Difference Time Domain (FDTD) method the specific design frequency 10 GHz and match impedance is 50 ohms. The simulation results of its characteristics are input impedance, return loss, VSWR and radiation patterns respectively.

• Current Optics and Photonics
• /
• 제1권6호
• /
• pp.637-641
• /
• 2017

We present dielectric constant measurements of thin films using THz metamaterials fabricated on a quartz substrate. The resonance shifts of the metamaterials exhibit saturation behavior with increasing film thickness. The saturation frequency shift varies with the real part of the dielectric constant, from which the numerical expression for the particular metamaterial design was extracted. We first performed finite-difference time-domain simulations to find an explicit relationship between the saturated frequency shift and the dielectric constant of a thin film, which was confirmed by the experimental results from conventional techniques. In particular, the quartz substrate enables us to determine their values more accurately, because of its low substrate index. As a result, we extracted the dielectric constants of various films whose values have not been addressed previously without precise control of the film thickness.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.864-869
• /
• 2004

A novel concept of feedback loop design for modal test and model updating is proposed. This method uses the closed -loop natural frequency information for parameter modification to overcome the problems associated with the conventional method employing the modal sensitivity matrix. To obtain new modal information from closed-loop system, controllers should be effective in changing modal data while guaranteeing the stability of closed-loop system. It is very hard to guarantee the stability of the closed-loop system with non-collocated sensor and actuator set. Ill this research, we proposed a controller called mode-decoupling controller that can change a target mode as much as the designer wants guaranteeing the stability of closed-loop system. This controller can be computed just using measured open-loop modeshape matrix. A simulation based on time domain input/output data is performed to check the feasibility of proposed control method.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 한국마이크로전자및패키징학회 2000년도 추계 기술심포지움 논문집
• /
• pp.23-27
• /
• 2000

Simultaneous Switching Noise (SSN) propagated through parallel power and ground planes in high-speed multilayer printed circuit boards (PCBs) causes malfunction of both digital and analog circuits. To reduce SSN, decoupling capacitors are generally used in the PCBs. In this paper, we improve the equivalent circuit model of decoupling capacitor in high-frequency range to analyze the effect of SSN reduction accurately. The analysis is performed by the microwave and RF design system (MDS) method and the finite difference time domain (FDTD) method. We compared the results by the ideal capacitor model with those by the proposed model.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• 제14권10호
• /
• pp.955-961
• /
• 2004

A novel concept of feedback loop design for modal test and model updating is proposed. This method uses the closed-loop natural frequency information for parameter modification to overcome the problems associated with the conventional method employing the modal sensitivity matrix. To obtain new modal information from closed-loop system, controllers should be effective in changing modal data while guaranteeing the stability of closed-loop system. But it is very hard to guarantee the stability of the closed-loop system with non-collocated sensor and actuator set. In this research, we proposed a controller called mode-decoupling controller that can change a target mode as much as the designer wants guaranteeing the stability of closed-loop system. This controller can be computed Just using measured open-loop modeshape matrix. A simulation based on time domain input/output data is performed to check the feasibility of proposed control method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.647-650
• /
• 2004

The modeling of an active vibration isolation system is accomplished by using the equivalent spring constant, mass and rotational Inertia of each component. The detailed model of the actuation module is successful for describing its frequency-domain performance but also too complicated to implement it to actual system for control so that the order of the model is reduced up to the degree that preserves its characteristic in the low frequency range. The reduced model is suitable for identifying the unknown system parameters such as damping constants of components. The overall isolation system is described by using the reduced model of the actuation module. The accurate model ing and system parameter identification that is essential for the control of the active vibration isolation system is attained successfully.

• Geomechanics and Engineering
• /
• 제18권6호
• /
• pp.639-650
• /
• 2019

Time-domain commercial codes are widely used to evaluate the seismic behavior of tunnels. Those tools offer a good insight into the performance and the failure mechanism of tunnels under earthquake loading. Viscous damping is generally employed in the dynamic analysis to consider damping at very small strains in some cases, and the Rayleigh damping is commonly used one. Many procedures to obtain the damping parameters have been proposed but they are seldom discussed. This paper illustrates the influence of the Rayleigh damping formulation on the tunnel visco-elastic behavior under earthquake. Four Rayleigh damping determination procedures and three soil shear velocity profiles are accounted for. The results show significant differences in the free-field and in the tunnel response caused by different procedures. The difference is somewhat decreased when the soil site fundamental frequency is increased. The conventional method which consists of using solely the first soil natural mode to determine the viscous damping parameters may lead to an unsafe seismic design of the tunnel. In general, using five times site fundamental frequency to obtain the damping formulation can provide relatively conservative results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제32권7C호
• /
• pp.658-666
• /
• 2007

In general, the earlier linear-phase MAXFLAT(maximally flat) lowpass FIR filters have the main disadvantage of a gain response in the half frequency band $(0{\leq}w{\leq}{\pi}/2)$ by the closed form transfer functions used in design techniques for realizing them. Moreover, most of them has existent problems as follows : ripple error in the stopband, gentle-cutoff attenuation, phase and group delay and inexact cutoff frequency response. It is due to the approximation algorithms such as Chebyshev norm and Remez exchange which are used to approach MAXFLAT and linear-phase characteristics in frequency domain. In this paper, a new mathematically closed-form transfer function is introduced for the design of MAXFLAT lowpass FIR filters which have the zero-phase and wideband-gain response. In addition, we verify that the closed-form transfer function is easily realized due to our generalized formulas derived newly by using MAXFLAT conditions including an arbitrary cutoff point. This method is, therefore, useful for "simple and quick designs". Conclusively, we propose a technique for the design of new zero-phase wideband MAXFLAT lowpass FIR filters which can achieve sharp-cutoff attenuation exceeding 250 dB almost everywhere.

• Structural Engineering and Mechanics
• /
• 제48권4호
• /
• pp.455-466
• /
• 2013

In recent years, many countries have added railway noise to the issues covered by noise regulations. It is known that the rail is the dominant source of rolling noise at frequency range of 500Hz-2000Hz for the conventional speeds (<160km/h). One of the effective ways to reduce noise from railway track is using a rail vibration absorber. To study the acoustic performance of rail absorber, the decay rates of vibration have long been used by researcher. In this paper, A FE model of a periodic supported rail with infinite element in ABAQUS is developed to study the acoustic performance of the rail absorber. To compute the decay rates, acceleration responses along the rail transferred to MATLAB to obtain response levels in frequency domain and then by processing the response levels, the decay rates obtained for each1/3octav band. Continous rail absorber is represented by a steel layer and an elastomer layer. The decay rates for conventional rail and rail with one-side absorber and also, the rail with two side absorber are obtained and compared. Then, to improve the system of rail absorber, a steel plate with elastomer layer is added to bottom of the rail foot. The vertical decay rate results show that the decay rate of rail vibration along the track is significantly increased around the tuned frequency of the absorber and thus the rail vibration energy is substantially reduced in the corresponding frequency region and also effective in rail noise reduction.