• Structural Engineering and Mechanics
• /
• v.55 no.6
• /
• pp.1261-1278
• /
• 2015

Due to their low intrinsic damping, stay cables in cable-stayed bridges have often exhibited unanticipated and excessive vibrations which result in increasing maintenance frequency and disruption to normal operations of the entire bridges. Mitigation of undesired cable vibration can be achieved by attaching an external damping device near the anchorage. High Damping Rubber (HDR) dampers have many advantages such as compact size, better aesthetics, easy maintenance, temperature stability, and cost benefits; therefore, they have been widely used to increase cable damping. Although a single damper has been shown to reduce cable vibrations, it is not the most effective method due to geometric constraints. This paper proposes the use of two HDR dampers to improve effectiveness and robustness in suppressing cable vibration. Oscillation parameters of the cable-dampers system were investigated in detail by modeling the stay cable as a taut string and each HDR damper as complex-valued impedance and by using an analytical formulation of the complex eigenvalue problem. The problem of two HDR dampers arbitrarily located along a cable is solved and the solution is discussed. Asymptotic formulas to calculate the damping ratios of the cable with two HDR dampers installed near the anchorage(s) are proposed and compared with the exact solutions. Further, a design example is presented in order to justify the methodology. The results of this study show that when the two HDR dampers are installed close to each other on the same end of the cable, some interaction between the dampers leads to reduced damping ratio. When the dampers are on the opposite ends of the cable, they are effective in increasing damping ratio and can provide better vibration reduction to multiple modes.

• Agribusiness and Information Management
• /
• v.10 no.1
• /
• pp.1-15
• /
• 2018

Many paddy cultivating farmers in the country are forced to use their limited resources to produce adequate food for their family, leading to the degradation and reduction in potential of these resources. The yield levels of paddy at the farmers' level and in the Front Line Demonstrations (FLDs) conducted in the farmers' fields is not at par with potential yield of the paddy variety. The gap between potential yield of crop variety and yield realized in FLDs refers to Research gap and the yield gap between FLDs and due to farmers' practice refers to Extension gap. The earlier studies conducted in India in general and in Andhra Pradesh in particular highlighted the existence of both research and extension gaps with reference to paddy. It is essential that, the narrowing of both research and extension gaps is not static, but dynamic considering the influence of technological interventions in boosting paddy yields at FLDs level and at farmers' level and also with the improvement of the yield potential of paddy varieties. This calls for integrated and holistic approaches to address these two gaps and with this background, the researcher aimed at this in depth study. The findings revealed that, research gaps are high with reference to weed management and pest management and extension gaps are high with reference to farm mechanization followed by fertilizer management. Reliable source of seed, capital use and frequency of meetings with Scientists or Agricultural Officers significantly influence the extension gaps in paddy. Farmers also prioritized socio-economic and technical constraints and the analysis infers that, it is high time now for the farmers to adopt the planned technological interventions on scientific scale to minimize the extension gaps to the extent possible. As the enabling environment in the State of Andhra Pradesh is highly encouraging for the farmers with relevant policy instruments in the form of subsidized inputs, free power, credit at concessional rates of interest, constructing irrigation projects etc., the adoption of the proposed technological interventions significantly contribute to minimizing both research and extension gaps in paddy cultivation in Kurnool district of Andhra Pradesh.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.30 no.3
• /
• pp.267-290
• /
• 2019

The purpose of this study is to investigate the current status and condition of continuing education to improve professionalism of school library and to suggest ways to improve continuing education. The survey was conducted for 69 librarians and school librarians teachers in elementary, middle and high school libraries in Goyang, Gyeonggi-do, and frequency analysis and cross analysis were conducted. The research results are as follows. First, the study found that librarians have a high interest in and participation in continuing education. Second, the type of continuing education with the highest percentage of participation was short-term training and training courses, and the link between educational content and practice was low. Third, managers' awareness needs to be improved, and regional constraints and the lack of suitable continuing education programs are the obstacles to continuing education. Fourth, preference for continuing education during working hours and vacation was emphasized. Through this, it was suggested that continuous and long-term continuing education, policy support for encouraging continuing education, development of continuing education courses for professionalism, manager's awareness call.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.9 no.4
• /
• pp.725-733
• /
• 2019

The study aimed to effect of leisure support and leisure constraints on life satisfaction for extreme sports participants. A total of 179 adults from Seoul, In-chon, Gyeonggi, and Chungcheng-do were recruited. I conducted frequency, reliability, confirmatory factor, correction, and structure equaling modeling analyses using PASW Statistics 18.0 and AMOS 18.0. The results were as follows: (1) leisure attitude of leisure activity participants had a positive influence on leisure satisfaction; (2) leisure attitude of leisure activity participants had no influence on psychology happiness; (3) leisure satisfaction of leisure activity participants had no influence on psychology happiness. Leisure satisfaction has no mediating effect between leisure attitude and psychological well-being. However, leisure attitude has a positive influence on leisure satisfaction, so we need to develop infrastructure which it continue participate in leisure activity.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.2
• /
• pp.618-633
• /
• 2014

Relay technology is becoming more important for mobile communications and wireless internet of things (IoT) networking because of the extended access network coverage range and reliable quality of service (QoS) it can provide at low power consumption levels. Existing mobile multihop relay (MMR) technology uses fixed-point stationary relay stations (RSs) and a divided time-frame (or frequency-band) to support the relay operation. This approach has limitations when a local fixed-point stationary RS does not exist. In addition, since the time-frame (or frequency-band) channel resources are pre-divided for the relay operation, there is no way to achieve high channel utilization using intelligent opportunistic techniques. In this paper, a different approach is considered, where the use of mobile/IoT devices as RSs is considered. In applications that use mobile/IoT devices as relay systems, due to the very limited battery energy of a mobile/IoT device and unequal channel conditions to and from the RS, both minimum energy consumption and QoS support must be considered simultaneously in the selection and configuration of RSs. Therefore, in this paper, a mobile RS is selected and configured with the objective of minimizing power consumption while satisfying end-to-end data rate and bit error rate (BER) requirements. For the RS, both downlink (DL) to the destination system (DS) (i.e., IoT device or user equipment (UE)) and uplink (UL) to the base station (BS) need to be adaptively configured (using adaptive modulation and power control) to minimize power consumption while satisfying the end-to-end QoS constraints. This paper proposes a minimum transmission power consuming RS selection and configuration (MPRSC) scheme, where the RS uses cognitive radio (CR) sub-channels when communicating with the DS, and therefore the scheme is named MPRSC-CR. The proposed MPRSC-CR scheme is activated when a DS moves out of the BS's QoS supportive coverage range. In this case, data transmissions between the RS and BS use the assigned primary channel that the DS had been using, and data transmissions between the RS and DS use CR sub-channels. The simulation results demonstrate that the proposed MPRSC-CR scheme extends the coverage range of the BS and minimizes the power consumption of the RS through optimal selection and configuration of a RS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1653-1660
• /
• 2016

The synthetic aperture rardar (SAR) is an active sensor using microwaves. It transmits a microwave signal, called a chirp pulse, and receives the reflected signal in a moving platform such as satellite and unmanned aerial vehicle. Since this sensor uses microwaves that can penetrate the atmosphere, SAR generates the images regardless of light and weather conditions. However SAR operates on the moving platform, the Doppler shift and the side-looking observation method should be considered. In addtion, a residual image or ghost image can be occurred according to selection of the pulse repetition frequency (PRF). In this paper, a range design of the PRF for the L-band spaceborne SAR system is studied for prevention of SAR image distortion. And the system is studied for prevention of SAR image distortion. And the system parameter and the PRF are calibrated iteratively according to the proposed system design procedure and design constraints. The MATLAB based on SAR system simulator has been developed to verify the validity of calculated PRF. The developed simulator assumes that SAR sensor is operated by the PRF calculated from the design. The results of the simulator show that the targets in image has a valid peak to side-lobe ratio (PSLR) so that the PRF can be used for the spaceborne SAR sensor.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.346-355
• /
• 2020

This study proposed a new optimization-based decision model for an enterprise resource planning and production scheduling of a pharmaceutical intermediates manufacturing plant. To do this work, we first define the inflow and outflow information as well as the model structure, and develop an optimization model to minimize the production time (i.e., makespan) using a mixed integer linear programing (MILP). The unique feature of the proposed model is that the optimal process scheduling is established based on real-time resource logistics information using a radio frequency identification (RFID) technology, thereby theoretically requiring no material inventories. essential information for process operation, such as the required amount of raw materials and estimated arrival timing to manufacturing plant, is used as logistics constraints in the optimization model to yield the optimal manufacturing scheduling to satisfy final production demands. We illustrated the capability of the proposed decision model by applying the optimization model to two scheduling problems in a real pharmaceutical intermediates manufacturing process. As a result, the optimal production schedule and raw materials order timing were identified to minimize the makespan while satisfying all the product demands.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.33 no.4
• /
• pp.271-277
• /
• 2020

There are increasing cases of monitoring the structural response of structures using multiple sensors. However, owing to cost and management problems, limited sensors are installed in the structure. Thus, few structural responses are collected, which hinders analyzing the behavior of the structure. Therefore, a technique to predict responses at a location where sensors are not installed to a reliable level using limited sensors is necessary. In this study, a numerical study is conducted to predict the seismic response of low-rise buildings using limited information. It is assumed that the available response information is only the acceleration responses of the first and top floors. Using both information, the first natural frequency of the structure can be obtained. The acceleration information on the first floor is used as the ground motion information. To minimize the error on the acceleration history response of the top floor and the first natural frequency error of the target structure, the method for predicting the mass and stiffness information of a structure using the genetic algorithm is presented. However, the constraints are not considered. To determine the range of design variables that mean the search space, the parameter prediction method based on artificial neural networks is proposed. To verify the proposed method, a five-story structure is used as an example.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.472-483
• /
• 2013

Actual maritime exercise for improving the capability of submarine sonar operator leads to a lot of cost and constraints. Sonar simulator maximizes the capability of sonar operator and training effect by solving these problems and simulating a realistic battlefield environment. In this study, a passive sonar simulator algorithm is suggested, where the simulator is divided into three modules: maneuvering module, noise source module, and sound propagation module. Maneuvering module is implemented in three-dimensional coordinate system and time interval is set as the rate of vessel changing course. Noise source module consists of target noise, ocean ambient noise, and self noise. Target noise is divided into modulated/unmodulated and narrowband/broadband signals as their frequency characteristics, and they are applied to ship radiated noise level depending on the vessel tonnage and velocity. Ocean ambient noise is simulated depending on the wind noise considering the waveguide effect and other ambient noise. Self noise is also simulated for flow noise and insertion loss of sonar-dome. The sound propagation module is based on ray propagation, where summation of amplitude, phase, and time delay for each eigen-ray is multiplied by target noise in the frequency domain. Finally, simulated results based on various scenarios are in good agreement with generated noise in the real ocean.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.1
• /
• pp.21-28
• /
• 2021

The main purpose of this study is to assess the safety of the fixed anchorages subjected to the seismic motion for an operating facilities in the actual power plant. Thus, the experimental study was conducted to investigate the load response in the event of an actual seismic to the anchorages of a nonstructural components. Since there are economic and spatial constraints to study nonstructural components that actually have various forms, alternative test specimens of steel frames with mass were built and the shaking table test was carried out. In order to evaluate the dynamic characteristics and seismic performance, the natural frequency of the target structure was identified through the shaking table test and then the load response characteristics of the anchorage were evaluated by generating an artificial seismic effect like actual seismic. Finally, the structural stiffness was reinforced by fixing the steel frame to the test specimen using bolts, thereby reducing the load transmitted to the anchorage. It will be carried out on the reliability verification of the experiments and areas that have not been carried out due to the site conditions through the analytical approach in the future.