• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.2
• /
• pp.702-721
• /
• 2012

In the DVB-T2 system with a multiple-input single-output (MISO) transmission mode, Alamouti coded orthogonal frequency division multiplexing (OFDM) signals are transmitted simultaneously from two spatially separated transmitters in a single frequency network (SFN). In such systems, each transmit-receive link may have a distinct carrier frequency offset (CFO) due to the Doppler shift and/or frequency mismatch between the local oscillators. Thus, the received signal experiences dual CFOs. This not only causes dual phase errors in desired data but also introduces inter-carrier interference (ICI), which cannot be removed completely by simply performing a CFO compensation. To overcome this problem, this paper proposes an iterative detection with dual phase errors compensation technique. In addition, we propose a successive-iterative ICI cancellation technique. This technique successively eliminates ICI in the initial iteration by exploiting pre-detected data pairs. Then, in subsequent iterations, it performs a fine interference cancellation using a priori information, iteratively fed back from the channel decoder. In contrast to previous works, the proposed techniques do not require estimates of dual CFOs. Their performances are evaluated via a full DVB-T2 simulator. Simulation results show that the DVB-T2 receiver equipped with the proposed dual phase errors compensation and the successive-iterative ICI cancellation techniques achieves almost the same performance as ideal dual CFOs-free systems, even for large dual CFOs.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7C
• /
• pp.706-712
• /
• 2006

In this letter, we propose a compact CORDIC processor for implementation of carrier frequency synchronization block in an OFDM (Orthogonal Frequency Division Multiplexing) system. The compact CORDIC processor is proposed by using inherenct properties of an OFDM system for estimation and compensation of carrier frequency offset, and is composed of a compact CORDIC preprocessor and a compact CORDIC processor. The compact CORDIC preprocessor plays a role of normalizing input signal efficiently, and the compact CORDIC processor is proposed to perform the vectoring mode and rotational mode jointly in CORDIC operation for carrier frequency synchronization. It is shown by FPGA implementation that the proposed compact CORDIC processor can achieve better performance with a significantly reduced hardware complexity than the conventional CORDIC approach.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.728-735
• /
• 2016

A 70 MHz temperature-compensated on-chip CMOS relaxation oscillator for mobile display driver ICs is proposed to reduce frequency variations. The proposed oscillator compensates for frequency variation with respect to temperature by adjusting the bias currents to control the change in delay of comparators with temperature. A bandgap reference (BGR) is used to stabilize the bias currents with respect to temperature and supply voltages. Additional temperature compensation for the generated frequency is achieved by optimizing the resistance in the BGR after measuring the output frequency. In addition, a trimming circuit is implemented to reduce frequency variation with respect to process. The proposed relaxation oscillator is fabricated using 45 nm CMOS technology and occupies an active area of $0.15mm^2$. The measured frequency variations with respect to temperature and supply voltages are as follows: (i) ${\pm}0.23%$ for changes in temperature from -30 to $75^{\circ}C$, (ii) ${\pm}0.14%$ for changes in $V_{DD1}$ from 2.2 to 2.8 V, and (iii) ${\pm}1.88%$ for changes in $V_{DD2}$ from 1.05 to 1.15 V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.11
• /
• pp.1156-1160
• /
• 2003

Many time-frequency analysis techniques have been used for motion compensated ISAR(Inverse Synthetic Aperture Radar) imaging. In this work, a novel time-frequency(T-F) analysis called evolutionary adaptive wavelet transform (EAWT) and evolutionary adaptive joint time-frequency(EAJTF) procedure are used for the motion compensated ISAR image. To show the validity of our algorism, we use simulated MIG-25 and Boeing 727(B-727) ISAR data. From the constructed ISAR image using EAWT and EAJTF, we show that our algorithm can obtain a clear motion compensated ISAR image such as other time-frequency analysis techniques.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.441-444
• /
• 1997

This paper describes the bending traveling-wave type ultrasonic motor which generates the traveling wave by combining two standing waves with phase difference time and space. In +2$0^{\circ}C$~3$0^{\circ}C$, the operation characteristic of USM has represented normal condition. But in the other temperature, the operation characteristic of USM has abnormal condition, that is driving frequency, drive current and r.p.m are down. The recent USM has controller without temperature compensation. This study aimed at fuzzy controller which must follow the frequency at operation temperature and then r.p.m and torque increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.866-873
• /
• 2000

Sliding mode control(SMC) incorporated with perturbation compensation is developed here to reduce the low-frequency tracking error in the presence of wide-band frequency perturbations for a nonlinear dynamic system. The control scheme is designed for estimation of low frequency perturbations with employment of the Time Delay Control and low-pass filter. It is shown that the SMC with perturbation compensation is far superior to the conventional SMC in tracking control of the dynamic systems under model uncertainties and external disturbance conditions.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.9
• /
• pp.872-875
• /
• 2010

This paper describes new harmonic disturbance compensation based on a peak filter array for Hard Disk Drives. Unlike a conventional method, the proposed method does not require any sin/cos functions or tables and reduces effects of all harmonic disturbances within a nyquist frequency. Two factors are introduced to parameterize stability and a gain tune. In addition, it is verified that the order of the proposed filter is minimal. From 600 experimental results, 8.5% performance improvement is achieved.

• ETRI Journal
• /
• v.32 no.4
• /
• pp.520-529
• /
• 2010

In this paper, we present a low-voltage low-dropout voltage regulator (LDO) for a system-on-chip (SoC) application which, exploiting the multiplication of the Miller effect through the use of a current amplifier, is frequency compensated up to 1-nF capacitive load. The topology and the strategy adopted to design the LDO and the related compensation frequency network are described in detail. The LDO works with a supply voltage as low as 1.2 V and provides a maximum load current of 50 mA with a drop-out voltage of 200 mV: the total integrated compensation capacitance is about 40 pF. Measurement results as well as comparison with other SoC LDOs demonstrate the advantage of the proposed topology.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.593-596
• /
• 1994

When a force impulse acting on a massive and plex object is measured with a dynamometer, be resonant vibration of the measurement system often leads to serious inaccuracies. A more accurate measurement is obtained when the transfer function ,of the object-dynamometer system is used to compensate for the error in the dynamometer's output signal. The natural frequency and the damping coefficient of the transfer function are estimated by analyzing the waveform of the free damped vibration period after the loading of the force has ended. The residue of the system is determined such that the compensated force spectrum becomes smooth within a neighborhood of the natural frequency. The effectiveness of this signal processing method is experimentally tested on a hammer impulse, under the assumption that the hammer's high resonant frequency accurately models the problems encountered in force impact measurement. The compensation method is used to derive a improved estimate of the hammer impulse.

• Journal of Korea Multimedia Society
• /
• v.16 no.8
• /
• pp.905-913
• /
• 2013

The Parallel Model Compensation Using Frequency-variant: FV-PMC for noise-robust speech recognition is a method to classify the noises, which are expected to be intermixed with input speech when recognized, into several groups of noises by setting average frequency variant as a threshold value; and to recognize the noises depending on the classified groups. This demonstrates the excellent performance considering noisy speech categorized as good using the standard threshold value. However, it also holds a problem to decrease the average speech recognition rate with regard to unclassified noisy speech, for it conducts the process of speech recognition, combined with noiseless model as in the existing PMC. To solve this problem, this paper suggests a enhanced method of recognition to prevent the unclassified through improving the extent of rating scales with use of maximum likelihood so that the noise groups, including input noisy speech, can be classified into more specific groups, which leads to improvement of the recognition rate. The findings from recognition experiments using Aurora 2.0 database showed the improved results compared with those from the method of the previous FV-PMC.