• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.179-192
• /
• 2008

A multiphase compensation method with mismatch linearization technique, is presented and demonstrated in a $\Sigma-\Delta$ fractional-N frequency synthesizer. An on-chip delay-locked loop (DLL) and a proposed delay line structure are constructed to provide multiphase compensation on $\Sigma-\Delta$ quantizetion noise. In the delay line structure, dynamic element matching (DEM) techniques are employed for mismatch linearization. The proposed $\Sigma-\Delta$ fractional-N frequency synthesizer is fabricated in a $0.18-{\mu}m$ CMOS technology with 2.14-GHz output frequency and 4-Hz resolution. The die size is 0.92 mm$\times$1.15 mm, and it consumes 27.2 mW. In-band phase noise of -82 dBc/Hz at 10 kHz offset and out-of-band phase noise of -103 dBc/Hz at 1 MHz offset are measured with a loop bandwidth of 200 kHz. The settling time is shorter than $25{\mu}s$.

• Journal of electromagnetic engineering and science
• /
• v.4 no.2
• /
• pp.72-78
• /
• 2004

In this paper, we evaluate the performance of the digital modulation schemes described in the APCO Project 25 FDMA specifications which can be used for applying the ultra-narrowband technology to the current domestic simple two-way radio systems, and discuss difficulties in the DSP implementation of the systems. We analyze the effect on the systems' BER performance of receiver non-matched filter and frequency-offset between the transmitter and receiver oscillators. And we present a frequency offset compensation method for improving the system performance. The results of performance analysis showed that the CQPSK of APCO Project 25 using non-matched filter degraded the BER by 0.5～1.0 ㏈ comparing with PI/4 DQPSK using matched filter. In the event of 2 % frequency offset, about 1 ㏈ performance loss was produced at the BER of $$10^{-3}TEX>. With the frequency-offset compensation method implemented in the systems using phase recovery scheme of PSK synchronization detection, the performance degradation of about 1.0 ㏈ was occurred at the BER of $$10^{-3}TEX> for 10 % of frequency offset. The proposed method can be used for the improvement of system performance.

• Bulletin of the Korean Space Science Society
• /
• 2005.04a
• /
• pp.138-142
• /
• 2005

A reaction wheel, an actuator for satellite attitude control, produces disturbance torque and force as well as its axial control torque. The disturbances have an influence on the pointing stability of high precision satellites. The measurement of disturbances for such a satellite, therefore, is necessary. The wheel's rotation, however, causes the vibration of the table and its vibration induces measurement errors, especially large near the resonance frequency of the Measurement table. For the purpose of overcoming these defects, a calibration method using frequency compensation is suggested in this paper. Disturbance parameters are identified from data examined by frequency compensation. Measurement frequency range can be expanded far higher than the resonance frequency, since the degradation of data accuracy caused by its vibration is well alleviated even in the resonance area.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.6
• /
• pp.551-557
• /
• 2006

The electrical frequency synchronized periodic torque ripple exits in the AC motor. There are various sources of torque ripple in AC motor such as current measurement error, dead time, etc. This paper proposes a compensation algorithm which suppresses undesired side effect known as the periodic torque ripple of AC motor. The torque ripple compensation classified as the speed ripple detector and torque ripple compensator. This paper proves a speed ripple minimization at steady state by analysis of torque ripple compensator. A new speed ripple detector improves the performance of torque ripple compensation algorithm. The simulation and experimental results show that the compensation algorithm is effective and the torque ripple compensation method improves the performance of speed ripple detector by eliminating torque ripples effectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.221-229
• /
• 2013

In this paper, the image formation by the motion compensation technique for Synthetic Aperture Radar system(SAR) were realized through the computer simulation. The motion compensation technique performed image data with the range compression, the compensation procedure, the azimuth compensation and the noise elimination procedure. The range compression procedure transform the SAR raw data into the frequency domain and correlate with the range reference function and then inversely transform into the time domain. The compensation procedure contain the aircraft fluctuations compensation and the radar image degrading effect elimination procedure which was caused by image formation algorithm itself. The aircraft fluctuations compensation procedure perform the first stage which correct the phase angle and the second stage which calculate the Doppler frequency and determine the coordinate of the received signal. The radar image degrading effect elimination procedure also perform range migration compensation and the image defocussing effect compensation. The azimuth compression procedure transform the compensation data to the frequency domain and correlate with the azimuth reference function. The azimuth correlated data are inversely transformed to the time domain which is called SAR image data. When the above procedure were completed, the image data contains the received signals mixed with noise. The threshold technique was applied to elimination the noise from the mixed image data.

• Journal of Power Electronics
• /
• v.9 no.5
• /
• pp.748-756
• /
• 2009

This paper presents a compensation algorithm for position error due to an amplitude imbalance between resolver output signals. Resolvers are typically used to obtain absolute position information for motor drive systems in severe environments. Position error is caused by an amplitude imbalance of the resolver output signals. As a result, the d- and q-axis currents of synchronous reference frame have periodic ripples in the stator fundamental frequency in permanent magnet synchronous motor (PMSM) drive systems. Therefore, this paper proposes a compensation algorithm to reduce the position error generated by the amplitude imbalance. The proposed method does not require any additional hardware, and reduces computation time with a simple integral operation according to rotor position. In addition, the position error can be directly compensated for by the estimated position error. The effectiveness of the proposed compensation algorithm is verified through several simulations and experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.9 no.1
• /
• pp.25-29
• /
• 1984

The active compensation of operational amplifeir is that it compensates the phase shift and the attennation of gain of OP Amp, according as the frequency increases. The compensation circuit is applied to VCVS and interting integrator. For VCVS, the phase shift of proposed compensated circuit is not concern with the frequency and the gain chracteristic is better than the proposde circuit by Soliman, according as the rate of feedback resistors of compensated circuit changes. Voltage follower accomplishies compgnsation using the same circuit. Also, the compensation circuit to increase O-ffactor in inverting integrator is proposed.

• ETRI Journal
• /
• v.26 no.1
• /
• pp.57-60
• /
• 2004

We propose an inductive compensation method for a surface-mountable 10 Gbps photoreceiver module. Since many typical 10 Gbps photoreceiver modules consist of a photodetector and low-noise pre-amplifier, the impedance mismatch between the photodetector and pre-amplifier, as well as package parasitics, may reduce the frequency bandwidth. In this paper, we inserted an inductive component between the photodetector and pre-amplifier in order to create frequency bandwidth expansion. From the measurement results, we have found that the proposed technique can increase the -3 dB bandwidth about 4.2 GHz wider compared with an uncompensated module. And, from a bit-error rate (BER) test, we observed -15.7 dB sensitivity at $10^{-12}$ BER. This inductive compensation can be implemented easily and is compatible with common manufacturing processes of photoreceiver modules.

• Journal of the Optical Society of Korea
• /
• v.8 no.4
• /
• pp.168-173
• /
• 2004

Brillouin scattering-based fiber optic sensors are useful to measure strain or temperature in a distributed manner. Since the Brillouin frequency of an optical fiber depends on both the strain and temperature, it is very important to know whether the Brillouin frequency shift is caused by the strain change or temperature change. This article presents a temperature compensation technique of a Brillouin scattering-based fiber optic strain sensor. Both the changes of the Brillouin frequency and the Brillouin gain power is observed for the temperature compensation using a BOTDA sensor system. Experimental results showed that the temperature compensated strain values were highly consistent with actual strain values.

• Transactions on Semiconductor Engineering
• /
• v.2 no.3
• /
• pp.1-5
• /
• 2024

This paper presents a crystal-less reference clock recovery (CR) frequency synthesizer with compensation designed for Bluetooth Low Energy (BLE) Smart-tag applications, operating at frequencies of 32, 72, and 80MHz. In contrast to conventional frequency synthesizers, the proposed design eliminates the need for external components. Using a single-ended antenna to receive a minimal input power of -36dBm at a 2.4GHz signal, the CR synthesizes frequencies by processing the RF signal received through a Low Noise Amplifier ( L N A ) . This approach allows the system to generate a reference clock without relying on a crystal. The received signal is amplified by the LNA and then input to a 16-bit ACC (Automatic Clock Compensation) circuit. The ACC compares the frequency of the received signal with the oscillator output signal, using the synthesis of a 32MHz reference clock through a frequency compensation method. The oscillator is constructed using a Ring Oscillator (RO) with a Frequency Divider, offering three different frequencies (32/72/80MHz) for various system components. The proposed frequency synthesizer is implemented using a 55-nm CMOS process.