• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.458-468
• /
• 2013

Large capacity reactive power compensation and harmonic control in the low-voltage grid of an enterprise, are important technical means to improve power quality and reduce power loss. In this paper, the principle of an efficient power quality controller is analyzed. Then, key application technologies of the HPQC which would influence the performances of the HPQC are studied. Based on an analysis of the harmonic shunt problem, a frequency dividing control strategy of the HPQC continuous subsystem is proposed. A parameter design method of the HPQC discrete subsystem and its installation method are also proposed to ensure the system compensation effect. HPQC systems have been designed for a copper foil plant. The effectiveness of this paper has been verified by the simulation and application results.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.2
• /
• pp.233-240
• /
• 2019

High-altitude ElectroMagnetic Pulse(HEMP) is a high-power electromagnetic pulse caused by nuclear explosions at altitudes above 30 km. This pulse can cause serious damage to the electrical/electronic device. Therefore, there are a lot of studies on the effects of HEMP in the literature. When conducting studies on the effects of HEMP, it is essential to measure the simulated HEMP. Depending on the need for measurement, this paper focuses on the HEMP measurement method. This paper proposes a measurement method using frequency domain compensation to extract the correct waveform and solves the offset problem more efficiently than the conventional methods. The proposed method is verified by experiment using HEMP simulator and measurement system in ADD.

• Journal of Biomedical Engineering Research
• /
• v.11 no.1
• /
• pp.13-18
• /
• 1990

Frequency responses of ambulatory electrocardiogram systems were measured. Phase shift was assessed by our improved Wagner's method. The characteristics of the systems were found much worse than that of ordinary ECG equipment both in gain and phase responses. The decay of -3dB in amplitude observed in 0.2Hz and the lead of 45 dog in phase was observed in 0.6Hz. In order to investigate which of these 2 responses play major role in generating false S -T deviation, mathe- matical filters were Composed in a computer and actual ECGs were fed. The false S-T deviation were found to be caused mostly by enormous lead in phase, and then, the compensation circuit to diminish the lead in phase was inserted in the commercial systemes. The compensated systems showed no false deviation in S-T segment.

• Journal of Advanced Navigation Technology
• /
• v.11 no.4
• /
• pp.394-400
• /
• 2007

We induced the optimal values of optical phase conjugator (OPC) position and dispersion coefficients of fiber sections depending on frequency chirp, which is substantially generated in optical signal by optical modulator and affects the transmission performances. In order to investigate the relation of optimal parameters with various frequency chirp, in this paper, positive(down) chirp, chirp-free and positive(up) chirp are assumed in 40 Gbps ${\times}$ 16 channels WDM transmission system of NRZ format with extinction ratio of 10 dB, which are the worst system parameters in the factor affecting system performance. It is confirmed that the OPC position offset and dispersion offsets between both fiber sections are more increased as frequency chirp become larger. It is also confirmed that the effect of the induced values on the compensation of WDM channels with negative frequency chirp is better than WDM channels with positive frequency chirp.

• The Journal of the Korea Contents Association
• /
• v.9 no.2
• /
• pp.10-17
• /
• 2009

This paper analyze the effect of frequency offset for the IEEE 802.15.4b LR-WPAN(Low-Rate Wireless Personal Area Network) with 915MHz bandwidth noncoherent DSSS O-QPSK based receiver system, and presents a compensation method with addition of differential filter to the system for compensation of frequency offset problem. DSSS PSSS-ASK and DSSS O-QPSK modulation techniques are accepted within the regularization of IEEE 802.15.4b. These new method can obtain 250kbps transmission rate. The DSSS O-QPSK modulation method that is used in this paper has no BER variation below 40ppm(frequency offset 36.6kHz), but if the offset frequency become high above 40ppm, then the system cannot have stable receiving condition due to worse BER. To solve this problem, we present a more stabilized receiver system at maximum frequency offset ${\pm}80ppm$ using MDDF unti a correlator of DSSS O-QPSK modulator. Moreover computer simulation results will be presented to evaluate the performance of the proposed algorithm unde various AWGN and frequency offset environment.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.42-48
• /
• 1994

A rotor flux error-based approach for correcting the rotor time constant estimation used in the slip frequency calculator of indirect field oriented controller is presented in this paper. The controller was derived from the d-q induction machine model. Slip frequency gain is dependent on the machine parameter errors. And parameter errors result in rotor flux error. Thus, estimated rotor flux is compared to commanded rotor flux. The error between them is used for the estimation of rotor time constant. Simulation results which demonstrate the performance of this approach are presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.23-30
• /
• 2014

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.399-407
• /
• 2010

SC-FDMA system uses DFT-spreading method for reducing the PAPR of OFDM signal, which improves the power efficiency. Block type pilot is used in SC-FDMA system. However, there are ICI due to the inevitable phase noise and frequency offset that can be generated from the Doppler frequency and inaccuracy between the transceiver oscillators. This ICI definitely degrades the BER performance. To overcome this problem and estimate the channel efficiently, we like to propose ICI compensation algorithm for the SC-FDMA system with comb type pilot. SLM method is additionally included for the PAPR reduction when pilot is assigned in comb type. Finally, it is confirmed that the ICI due to the phase noise and frequency offset is efficiently compensated by the suggested algorithm.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.509-517
• /
• 2013

In this paper, we researched a method that makes a good acoustic-speech system using a digital signal processing technique with dynamic microphone as a transducer. Good acoustic-speech system should deliver the original sound input to electric signal without distortion. By measuring the frequency response of the microphone, adjustment factors are obtained by comparing measured data and standard frequency response of microphone for each frequency band. The final sound levels are obtained using the developed adjustment factors of frequency responses from the microphone and speaker to match the original sound levels using the digital signal processing technique. Then, we minimize the changes in the frequency response and level due to the variation of the distance from source to microphone, where the frequency responses were measured according to the distance changes.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.6
• /
• pp.1042-1047
• /
• 2008

As an ultra-precision measurement system the heterodyne laser interferometer plays an important role in semiconductor industry. However the errors of environment and nonlinearity which are caused by air refraction and frequency-mixing separately reduce the accuracy of displacement measurement. In this paper we propose a DFNN(data fusion and neural network) method for error compensation. As a hybrid method of data fusion and neural network, DFNN method reduces the environmental and nonlinear error simultaneously. The effectiveness of the proposed error compensation method is proved through experimental results.