• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.613-618
• /
• 2018

In this paper, an active snubber type flyback converter was applied to a 60W class adapter and its test results are reported by producing a prototype. Especially, the prototype of the adapter was designed for both input voltage of 110V and 220V. The output voltage was designed for 60W with 19V class which is the most commonly used in laptops. The prototype was designed to a volume of about $50cm^3$ and a power density of about $1.22W/cm^3$ to minimize the size and verify portability. The maximum efficiency of the prototype was 90.88% at its maximum load of 60W against input voltage change and 91.04% was observed at 60W under input voltage of 220V. Furthermore, the stability of the output voltage against load power was observed to be within about 0.07%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.940-946
• /
• 2015

In this paper, we study a method that amplifies the output gain of a high voltage pulse using 300 kHz or higher frequency. We conducted a study on a method for amplifying the output gain using the resonance between the capacitance components of the load and the parasitic components of the circuit, instead of the conservative method for amplifying the pulse-amplitude by raising the voltage of the power stage. In particular, the method simplifies the circuit configuration throughout the appliance of flyback-type topology instead of the bridge-type. There are advantages that prevent damage from overload and the heat in the output circuit through the hard switching by amplifying the gain of the output voltage applying to the load as given by the capacitance component of the output electrode to the output pulse waveform. This study proposed a method to enhance the spatial and electrical efficiency of the contact-type heating device through the dielectric heating method applied to the field of medical and industrial heating.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.677-687
• /
• 2018

This paper presents a novel power decoupling control scheme with the bidirectional buck-boost converter for primary-side regulation photovoltaic (PV) micro-inverter. With the proposed power decoupling control scheme, small-capacitance film capacitors are used to overcome the life-span and reliability limitations of the large-capacitance electrolytic capacitors. Then, an improved flyback PV inverter is employed in continuous conduction mode with primary-side regulation for the PV power conditioning. The proposed power-decoupling controller shares the reference for primary side current regulation of the flyback PV inverter. The decoupling controller shapes the input current of the bidirectional buck-boost converter. The shared reference eliminates the phase-delay between the input current to the bidirectional buck-boost converter and the double frequency current at the PV primary current. The elimination of the phase-delay in dynamic response enhances the ripple rejection capability of the power decoupling buck-boost converter even with small film capacitor. With proposed power decoupling control scheme, the additional advantage of the primary-side regulation of flyback PV inverter is that there is no need to have an extra current sensor for obtaining the ripplecurrent reference of the decoupling current-controller of the power-decoupling buck-boost converter. Therefore, the proposed power decoupling control scheme is cost-effective as well as the size benefit. A new transient analysis is carried out which includes the source voltage dynamics instead of considering the source voltage as a pure voltage source. For verification of the proposed control scheme, simulation and experimental results are presented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.491-499
• /
• 2019

Recently, there has been increasing demand for power quality in power supply devices. The IEC 61000-3-2 standard requires that the AC / DC power supply for lighting meet the specifications for the power factor (PF) and total waveform distortion (THD). In addition, advanced countries in Europe are regulating the ripple rate as 15 ~ 30% for the flicker phenomenon caused by the change in the amount of foot energy due to the change in current of the output terminal. Therefore, domestic standards and regulations are being updated. This study adopted the Flyback converter to satisfy the PFC standard, and has the circuit first and second insulation function. To reduce the low frequency ripple of the LED current, Flyback, Coupled Inductor, LC parallel resonance filter, LLC resonance filter, and Cuk were simulated by PSIM to mimic each LED driving circuit. A coupled LC resonant circuit with a coupled inductor on the primary side and LC resonance on the secondary side was also proposed for output side ripple reduction.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.90-92
• /
• 2009

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.493-494
• /
• 2010

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5409-5415
• /
• 2012

Piezo ceramic actuator is used for various industrial products such as spray, dispenser, and valve control etc. Since the deflection of the piezo ceramic element depends on the applied voltage, it is required a power amplifier with high voltage supply for driving the piezo ceramic actuators. In this paper, we develop a simple H-bridge type power amplifier and a compact flyback type high voltage switching mode power supply for piezo ceramic actuators. It is easy to adjust the amount of energy input to piezo ceramic actuator by pulse-width-modulation with H-bridge type power amplifier.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1318-1328
• /
• 2015

The photovoltaic (PV) power conditioning system for small-scale applications has gained significant interest in the past few decades. However, the standalone mode of operation has been rarely approached. This paper presents a two-stage multi-level micro-inverter topology that considers the different operation modes. A multi-output flyback converter provides both the DC-Link voltage balancing for the multi-level inverter side and maximum power point tracking control in grid connection mode in the PV stage. A modified H-bridge multi-level inverter topology is included for the AC output stage. The multi-level inverter lowers the total harmonic distortion and overall ratings of the power semiconductor switches. The proposed micro-inverter topology can help to decrease the size and cost of the PV system. Transient analysis and controller design of this micro-inverter have been proposed for stand-alone and grid-connected modes. Finally, the system performance was verified using a 120 W hardware prototype.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.229-230
• /
• 2016

기존 자가발전 운동기구용 컨버터의 경우, 운동레벨을 조절하기 위한 입력임피던스 조절기능이 없거나, 조절기능을 추가하는 경우 복잡한 topology를 동반되는 경우가 일반적이다. 또한 복잡한 회로를 추가하게 되면 회로의 전체적인 부피가 증가하고, 원가가 상승할 뿐만 아니라, 회로의 신뢰성도 현저하게 저하시키는 등 회로 상용화를 어렵게 만든다. 본 논문에서는 입력 전압 및 전류 제어 방식을 이용하지 않고, 컨버터 구조 자체로 입력 임피던스를 제어하는 방식을 제안한다. 제안 방식은 입력전압, 입력전류 두 가지의 제어를 실행하지 않음으로써 복잡한 피드백 제어 단의 삭제가 가능하며, 이를 통해 회로의 높은 신뢰성 및 부피, 원가 감소 효과를 얻을 수 있다. 본 논문에서는 Flyback 컨버터를 이용하여, 이론적 특성 분석과 200W급 시작품을 통한 실험적 분석을 통해 그 타당성을 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.405-412
• /
• 1999

Meta! Halide Discharge(]\1HD) Iamps have good color rendition, long life and good focusing capability but h have flickers bv acoustic resonances. We have designed the electronic ballast for reducing acoustic resonances in high pressure discharge tube. The ballast consists of main two parts, the first part is a half-bridge inverter to make a square wave form a and the st'Cond part is a flyback converter to combine the low frequency and high frequency component. As a r result of this study, we conclude that MHD lamps of 70 watt 따c very well light(D without acoustic resonance p phenomena by the elestronic ballast.