• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1792-1795
• /
• 1997

It is difficulte to control in the flow system because there are many disturbance. So it is impossible to control delicately sometimes by PI or PID. In this paper, we study on the application of intellignet control algorithms such as 2DOF PID control, neural network, Fuzzy contro, Relay feedback to the flow control system. the resultings are 2DOF-PID control is more good response.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.2
• /
• pp.347-354
• /
• 1987

Timing simulators are widely used nowadays for analyzing large-scale MOS digital circuits, which, however, have several limitations such as nonconvergence and/or in accuracy for circuits containing tightly coupled feedback elements or loops. This paper describes a new timing simulator which aims at solving these problems. The algorithm employed is based on the wave-form relaxation method, but exploits the signal flow along the feedback loops. Each of feedback loops is treated as one circuit block and then local iterations are performed to enhance the timing simulation. With these techniques, out simulator can analyze the MOS digital circuits with up to 5-20 times of the magnitude speed improvemnets as compared to SPICE2, while maintaining the accuracy.

• KIPS Transactions on Software and Data Engineering
• /
• v.8 no.8
• /
• pp.317-322
• /
• 2019

Programming judge systems for programming training support are typically built on the Web, where the examiners uploads a programming problem, which the student reads and submits an answer to the problem. The judge system executes the submitted answer of source code to provide feedback such as pass, failure, and error messages. Students who receive the feedback except for the pass continues debugging the source code until they are judged to pass. We developed an online judge system to support programming training and analyzed answers submitted by the students and found that many of the students who were not judged to pass that test did not know exactly where they were wrong but continued to solve the problem. The current judge system generally feeds runtime error messages back to students. However, with only runtime error message, it is difficult for student who train to find the wrong part of the answer. Therefore, in this paper, we propose a system that provides the feedback of programming failure by analyzing the control flow of the test cases used in the source code submitted by the student. The proposed system helps students find the wrong parts more quickly by feeding back the paths where faults in the control flow may exist. In addition, we show that this system is applicable to the answer source code that the actual student submitted.

• Journal of the Korean Mathematical Society
• /
• v.34 no.4
• /
• pp.841-857
• /
• 1997

We present analysis and some computational methods for boundary optimal and feedback control problems for Navier-Stokes equations. We use one example to illustrate our methodology and ideas which are applicable to general control problems for Navier-Stokes equations. First, we discuss the existence of optimal solutions and derive an optimality system of equations from which an optimal solution may be computed. Then we present a gradient type iterative method. Finally, we present some numerical results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.327-330
• /
• 2004

Laser aided direct metal deposition (LADMD) process offers the ability to make a metal component directly from 3-D CAD dimensions. A 3-D object can be formed by repeating laser cladding layer by layer. The key of the build-up mechanism is the effective control of powder delivery and laser power to be irradiated into the melt-pool. A feedback control system using optical sensors is introduced to control laser power and powder mass flow rate. Using H13 tool steel and $CO_2$ laser system, comprehensive analysis are executed to test the efficiency of the system. In addition, the dimensional characteristics of directed deposited material are investigated with the parameters of deposition thickness, laser power, traverse speed and powder mass flow rate.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.3
• /
• pp.160-166
• /
• 2016

This study proposes the development and performance evaluation of electronic proportional control valve having an LVDT. The electronic proportional control valve is composed of hydraulic valve, proportional solenoid and controller. LVDT is to reduce the steady state error for the reference input of the controller by the feedback signal to detect the displacement of the spool. Designed LVDT is applied to the common proportional valve. In order to evaluate the performance of the developed valve, the hydraulic test equipment was developed and flow tests were carried out. From experimental results, it was proved that the hysteresis was less than 1% based on the maximum flow rate.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.46.5-47
• /
• 2008

• Journal of Mechanical Science and Technology
• /
• v.16 no.12
• /
• pp.1561-1575
• /
• 2002

A reduced-order linear feedback controller, which is used to control the linear disturbance in two-dimensional plane Poiseuille flow, is applied to a boundary layer flow for stability control. Using model reduction and linear-quadratic-Gaussian/loop-transfer-recovery control synthesis, a distributed controller is designed from the linearized two-dimensional Navier-Stokes equations. This reduced-order controller, requiring only the wall-shear information, is shown to effectively suppress the linear disturbance in boundary layer flow under the uncertainty of Reynolds number. The controller also suppresses the nonlinear disturbance in the boundary layer flow, which would lead to unstable flow regime without control. The flow is relaminarized in the long run. Other effects of the controller on the flow are also discussed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.8
• /
• pp.535-542
• /
• 2016

In this study, a model reference adaptive controller is developed to regulate the outlet air flow rate of centrifugal compressor for automotive supercharger. The centrifugal compressor is developed using the analytical based method to predict the transient behavior of operating and the designed model is validated with experimental data to confirm the system accuracy. The model reference adaptive control structure consists of a compressor model and a MRAC(model reference adaptive control) mechanism. The feedback control do not robust with variation of system parameter but the applied adaptive control is robust even if the system parameter is changed. As a result, the MRAC was regulated to reference air flow rate. Also MRAC was found to be more robust control compared with the feedback control even if the system parameter is changed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.738-750
• /
• 1994

The load-sensing hydraulic system which was developed to improve energy efficiency of conventional hydraulic systems has its own properties. The instability of system responses, linearity of a servo valve, robustness for variation of external load, and dynamic interference between hydraulic motors are such properties which have much to do with control properties of the system. The load-sensing hydraulic system has instability tendancy because the load-sensing mechanism makes a positive feedback loop between the motor part and the pump part. A flow property of the servo valve can be said to be linear because the flow through the valve has nothing to do with a load pressure and the flow is strictly proportional to a valve opening which is adjusted by a valve command signal. The resultant control property can be said to be robust because the steady-state control performance is independent to the load actuated on the motor shaft. In the case when one pump simultaneously drives more than two hydraulic motors, the pump outlet pressure is determined by a hydraulic motor of the largest load pressure among all of the hydraulic motors, and, thus, the other motors are dominated by the largest load pressure. That is, the other motors can be said to be interfered by the motor of the largest load pressure.