• 설비공학논문집
• /
• 제13권6호
• /
• pp.490-496
• /
• 2001

An experimental study on the behavior of the water hold-up by condensation of a fin-and-tube heat exchanger with regard to the surface characteristics, i.e., contact angle, was conducted. The static and dynamic contact angles were measured, and condensation experiments were conducted. Flow patterns on the fins with different surface characteristics were visualized. Results showed that the static contact angle is proportional to the dynamic contact angle within the range of this study. The water hold-up of the heat exchanger increases as the static or dynamic contact angle of its surfaces increases. Existence of transition of flow patterns was found as the static or dynamic angle increase. Due to the transition in the flow patterns, changes in the gradient of the water hold-up is occurred around the static angle of 8$0^{\circ}C$.

• 한국해양공학회지
• /
• 제19권1호
• /
• pp.8-13
• /
• 2005

In a multiple array of vertical cylinders, flaw patterns are very complex and very interactive between cylinders. The patterns are turbulent and non-linear depending on various factors. The gap and flow incoming velocity of upstream can affect on the downstream cylinder. In this study, the flaw characteristics around two vertical cylinders are investigated numerically and experimentally. As the gap between cylinders is changed at fixed coming velocity, the pressure distributions around cylinders are observed and compared by experimental and numerical approaches. The F.D.M and multi-block method are applied in the study. The pressures at 12 points around the cylinder are measured in the experiment. The results can be applied in the understanding and design of multiple pile array structures.

• 한국측량학회지
• /
• 제4권2호
• /
• pp.59-75
• /
• 1986

본 연구는 LANDSAT MSS Data를 연안해역의 수리현상파악을 목적으로 이용하는 경우의 가장 효과적인 화상해석방법을 모색한 것이다. 우리나라 인천지역을 대상으로, 육역에 비하여 CCT Data값이 낮은 해역의 LANDSAT MSS Data를 사용하여 화상강조의 기법인 Contrast 강조처리, Color 합성처리 및 비연산처리 등 화상처리를 실행함으로써, 연안해수역의 유동특성을 파악하기 위한 가장 효과적인 LANDSAT MSS Data의 화상해석순서를 제안하였다.

• 한국물환경학회지
• /
• 제31권2호
• /
• pp.196-208
• /
• 2015

This study analyzed the characteristics of sewer flow and its water quality, and investigated changes in the characteristics in three areas where the sewer rehabilitation projects have been carried out. In S1 area, the patterns of the flow became regular and the range of the fluctuation decreased after the sewer rehabilitation. The flow and its BOD concentration increased. The infiltration/inflow and exfiltration showed clear distinction before and after the sewer rehabilitation in this area. In S2 area, the patterns and the range of the fluctuation of the flow made no differences before and after the sewer rehabilitation. The flow decreased slightly and its BOD concentration increased considerably after the sewer rehabilitation. Big decrement in stormwater inflow but small in exfiltration appeared in this area. In S3 area, the patterns and the range of the fluctuation of the flow made no differences before and after the sewer rehabilitation. The flow decreased slightly and its BOD concentration increased in a small rate in this area.

• 한국가시화정보학회지
• /
• 제15권1호
• /
• pp.11-18
• /
• 2017

A two-phase flow observed in a heat exchanger or nuclear power generation often has a profound effect on undesirable noise or flow characteristics. Void fraction, which refers to the ratio of gas (or liquid) to the total fluid, affects heat transfer coefficient, vibration and so forth. In other words, void fraction is one of most important parameters in two-phase flow since it contributes to comprehend the characteristics of two-phase flow. We developed a two-phase flow visualization system to measure cross-sectional and volumetric void fractions by using quick closing valves and image processing software. With this system, we could observe the plug, slug, and stratified flow patterns of two-phase flow and measure a myriad of void fractions. As a consequence of the experiment, we found that the estimated void fractions were largely coincident with the predictive values by Chisholm model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.211-216
• /
• 2001

Flow motion and variation of thermal field around a bubble which attached at the upper cooled solid wall in a $B\dot{e}nard$ convection flow is studied experimentally using thermo-sensitive liquid-crystal tracers and image processing for flow visualization and analysis. The air is injected gradually by $0.1m\ell$ to make the bubble. As the growing of the bubble in a $B\dot{e}nard$ convection flow, the variation of temperature field and surface tension along the bubble, which in turn cause to change the thermal field patterns and the flow direction and patterns. 6 cells flow pattern is transformed into diverse flow pattern. At the large size of a bubble, it's only conduction mechanism under the region of the bubble because of low Ra number 1137, but the convection flow both sides of the bubble leads to another convection flow in the bubble influence area which has been remained stable stagnation.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.142-147
• /
• 2004

The flow in the LOX manifold of liquid rocket has been investigated using a CAE technique with an objective of economical modeling of injection holes in order to reduce the overall computational cost of flow analysis during the optimal rocket design procedure. The computational geometry is very close to that of the actual rocket design and the flow condition through the injection holes resembles that in the actual manifold of the liquid rocket. The result shows that the flow in the plane just above the injection holes is not uniformly distributed in terms of pressure and mass flow rate and this is attributed to the large-scale flow patterns present the LOX manifold. Thus, the flow physics should be understood correctly before making any attempt to model the injection holes. In the present study, several boundary conditions which were designed to effectively replace the presence of injection holes have been tested and it was found that a simple modeling can be possible by mimicking the actual geometry of the injection holes. By using this simple injection hole modeling, it was able to obtain about 30% reduction in computational cost but it was still able to reproduce the flow patterns correctly. Also the flow has been analyzed after incorporating a couple of different types of pre-distributors in LOX manifold and the effect of those will be discussed.

• 소성∙가공
• /
• 제14권1호
• /
• pp.49-56
• /
• 2005

In the semi-solid die casting process, an important thing is the flow behavior of semi-solid materials. The flow patterns of the semi-solid material can make the defects during die filling. To control the flow patterns is very important and difficult. In this paper, the flow behavior of the semi-solid A356 alloy material during die filing at various die gate shapes has been observed with the grain size controlled material. The effect of the gate shape on the die filling characteristics was investigated. The filling tests in each plunger stroke were experimented, and also simulated on the semi-solid material die casting process by MAGMAsoft. According to the filling tests and computer simulation, the effect of the gate shape on liquid segregation has been investigated.

• 한국항공운항학회지
• /
• 제18권4호
• /
• pp.86-91
• /
• 2010

New Design configurations of the fighter aircraft igloo diffuser were studied based on the closed ventilation type in contrast to the conventional open distribution type. To validate the enhanced and safe performance, the exhaust flow patterns of the two igloo diffuser types were simulated by both experimental and computational approaches as design tools. Flow visualizations were conducted to investigate the exhaust flow patterns in experimental approach. In addition, the commercial code called Fluent was used to calculate flow field properties. Computational simulations provided detailed parametric studies that significantly reduced the amount of experimentation necessary to alter the design parameters of the existing fighter igloo diffuser. The closed ventilation type of the igloo diffuser was shown the better results.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.199-206
• /
• 2004

In the multi-burner power plant, uneven supplies of combustion air to multi-burner are induced by unbalanced flow distribution in the windbox. These flow patterns tend to make flame unstable, increase the formation of pollutants and lower the overall combustion efficiency. To prevent these disadvantages, flow patterns in the windbox should be investigated and made to be distributed uniformly, In this study, scaled windbox model was used for tests and measured the velocities at the exit of the each burner and compared those with the CFD results.