• 반도체디스플레이기술학회지
• /
• 제8권2호
• /
• pp.31-35
• /
• 2009

In the silicon wafer polishing process, the mounting stage of silicon wafer on the ceramic carrier block has been using the polishing template which utilizes the porous surface instead of traditional wax mounting method. Here in this article, the experimental study is carried out in order to study the wafer demounting by water jet and the effects of operating conditions such as the water jet flowrate and the number of water jet nozzles on the wafer demounting time. It is found that the measured wafer demounting time is inversely proportional to the water flowrate per nozzle, regardless of number of nozzles used; implying that the stagnation pressure by the water jet impingement is the dominant key factor. Additionally, by using the transparent disk instead of wafer, the air bubble formation and growth is observed under the disk, making the passage of water flow, and subsequently demounting the wafer from the porous pad.

• 한국산림과학회지
• /
• 제101권3호
• /
• pp.538-545
• /
• 2012

본 연구는 산림유역의 일시하천과 간헐천이 상존하는 수변지역을 대상으로 산림벌채로 인한 토양의 교란 정도를 평가하고, 물리적 수문학적 특성 변화 양상을 파악하였다. 총 12개 소유역에서 4개의 처리구(BMP1, BMP2, 개벌구, 대조구)를 적용하였으며, 각 처리구별 벌채 전 후 1년 동안의 모니터링 결과를 비교 분석하였다. 그 결과, 벌채 후 산정된 교란등급은 벌채강도와 상관이 있는 것으로 나타났으며, 조사된 토양의 물리적 수문학적 특성 변화와 일치하는 경향을 보였다. 그러나, 용적밀도 및 공극률의 변화와는 일치하지 않았다. 전면개벌은 강도 높은 지표교란을 야기 시켰으며, 이로 인해 조공극률 및 투수계수는 감소, 토양강도는 증가하였고, 이는 토양의 침식의 간접적인 원인으로 작용하였다. 개벌구에서 강도 높은 지표 교란으로 야기된 토양의 물리적 수문학적 특성 변화는 BMP1과 BMP2에서 완화되는 것으로 나타났다. 그러나, 벌채 후 BMP2에 남겨진 벌채잔재물은 지표의 피복기능으로서의 침식을 완화하는 효과가 없는 것으로 나타났다.

• 한국가시화정보학회지
• /
• 제21권1호
• /
• pp.80-93
• /
• 2023

We performed numerical simulations of blood flow in an arterial cerebral artery aneurysm to investigate the hemodynamic behavior after coil embolization. A patient-specific model was created based on CTA data. We also conducted the coil embolization simulation to obtain the coil placement within the aneurysm. Blood was assumed to be an incompressible Newtonian fluid, and both the vessel and coil were considered rigid walls. The pulsatile boundary condition was applied at the inlet, and the outflow boundary conditions were used at the outlets. Our findings demonstrated that the coil embolization significantly reduces the blood volume flowrate entering the aneurysm by effectively blocking the inflow jet, leading to a decrease in both TAWSS and WSS, especially at the systolic peak in the impingement zone. While several high OSI regions disappeared over the aneurysm surface, we observed high OSI regions with a relatively small area where the coil did not completely occlude the aneurysm. Overall, these results quantitatively analyzed the effectiveness of coil embolization by focusing on hemodynamic indicators, potentially preventing aneurysm rupture. The present work could contribute to the development of patient-specific coil embolization.

• 설비공학논문집
• /
• 제12권12호
• /
• pp.1098-1125
• /
• 2000

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering in 1998 and 1999 has been done. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environment. The conclusions are as follows. 1) A review of the recent studies on fluid flow, turbomachinery and pipe-network shows that many experimental investigations are conducted in applications of impingement jets. Researches on turbulent flows, pipe flows, pipe-networks are focused on analyses of practical systems and prediction of system performance. The results of noise reduction in the turbomachinery are also reported. 2) A review of the recent studies on heat transfer analysis and heat exchanger shows that there were many papers on the channel flow with the application to the design of heat exchanger in the heat transfer analysis. Various experimental and numerical papers on heat exchanger were also published, however, there were few papers available for the analysis of whole system including heat exchanger. 3) A review of the recent studies on heat pump system have focused on the multi-type system and the heat pump cycle to utilize treated sewage as the heat source. The defrosting and the frosting behaviors in the fin-tube heat exchanger is experimentally examined by several authors. Several papers on the ice storage cooling system are presented to show the dynamic simulation program and optimal operation conditions. The study on the micro heat pipes for the cooling of high power electronic components is carried out to examine the characteristics of heat and mass transfer processed. In addition to these, new type of separate thermosyphon is studied experimentally. 4) The recent studies on refrigeration/air conditioning system have focused on the system performance and efficiency for new alternative refrigerants. New systems operating with natural refrigerants are drawing lots of attention. In addition to these, evaporation and condensation heat transfer characteristics of traditional and new refrigerants are investigated for plain tubes and also for microfin tubes. Capillary tubes and orifice are main topics of research as expansion devices and studies on thermophysical properties of new refrigerants and refrigerant/oil mixtures are widely carried out. 5) A review of the recent studies on absorption cooling system shows that numerous experimental and analytical studies on the improvement of absorber performance have been presented. Dynamic analysis of compressor have been performed to understand its vibration characteristics. However research works on tow-phase flow and heat transfer, which could be encountered in the refrigeration system and various phase-change heat exchanger, were seemed to be insufficient. 6) A review of recent studies on duct system shows that the methods for circuit analysis, and flow balancing have been presented. Researches on ventilation are focused on the measurement of ventilation efficiency, and variation of ventilation efficiency with ventilation methods by numerous experimental and numerical studies. Furthermore, many studies have been conducted in real building in order to estimate indoor thermal environments. Many research works to get some information for cooling tower design have been performed but are insufficient. 7) A review on the recent studies on architectural thermal environment and building mechanical systems design shows that thermal comfort analysis is sitting environment, thermal performance analysis of Korean traditional building structures., and evaluation of building environmental load have been performed. However research works to improve the performance of mechanical system design and construction technology were seemed to be insufficient.

• 한국수자원학회논문집
• /
• 제52권10호
• /
• pp.743-752
• /
• 2019

만곡수로에서의 흐름은 나선형 운동 형태의 이차류가 지배적이며, 이로 인해 일반적으로 만곡 외측을 따라 침식 현상이 발생하게 된다. 이러한 이차류를 약화시키기 위해서 보통 만곡수로 외측을 따라서 수제와 같은 수공구조물을 설치한다. 이 연구에서는 OpenFOAM 오프소스 소프트웨어를 토대로 난류 해석을 위한 하이브리드 RANS/LES 기법과 자유수면 해석을 위한 VoF기법을 이용한 3차원 수치모의를 통해서 $90^{\circ}$ 만곡수로에 설치된 잠긴수제가 후루드수가 0.43인 조건에서 이차류의 발달에 미치는 영향을 분석하였다. 시간과 공간에 대해서 2차 정확도의 유한체적법을 이용하여 수치모의를 수행하였으며, 수치해석 결과는 실험결과와 비교하여 수치모의의 정확도를 평가하였다. 잠긴수제가 설치된 경우의 수치모의 결과를 흐름방향 유속 분포와 횡방향 순환 유속벡터장을 중심으로 수리실험 관측값들과 비교할 때 수치모의 결과는 수리실험에서 관측된 주요 이차류 흐름 거동과 현상들을 대부분 양호한 정확도로 잘 재현하는 것으로 나타났다. 수치모의 결과를 비교해보면, 잠긴수제 설치로 인해서 만곡이 끝나는 단면 외측 하상부근에서의 유속은 약 평균유속의 1/3 정도 감소하는 반면에 수제 상단부에서의 전단층 발달에 따른 흐름 가속으로 자유수면 부근까지 유속이 증가하고 만곡 수충부에서는 수면 부근 유속이 약 20% 증가하는 것으로 나타났다. 결과적으로 잠긴수제는 만곡부에서 발생하는 이차류의 강도를 약화시켜 만곡부 외측 하상의 안정에 도움이 될 것으로 판단된다. 한편, 각 잠긴수제 전면부에서 말발굽와가 그리고 후면부에서는 후류가 형성되면서 수제 구조물 주변에서 강한 국부세굴이 발생하는 것으로 나타남으로, 국부세굴을 최소화할 수 있는 수제의 형상 및 배열에 대한 추가 연구가 요구된다.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.357-366
• /
• 1986

본 연구에서는 3공피토우관 및 열선유속계를 사용하여 벽에 평행한 2차원 난류제트의 난류량들을 측정하였고, 스캐니 밸브를 이용하여 벽면아력분포를 측정함 으로써 재순환 영역을 포함한 전체유동장에서의 유동특성을 고찰하였다. 또한 잘 알려진 표준 k-.epsilon. 난류모형 및 유선곡률을 고려한 수정된 k-.epsilon. 난류모형을 이용하여 측정 수치해석을 수행하였다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.43-55
• /
• 2000

In traditional electronic packages the die and the substrate are interconnected with fine wire. Wire bonding technology is limited to bond pads around the peripheral of the die. As the demand for I/O increases, there will be limitations with wire bonding technology. Flip chip technology eliminates the need for wire bonding by redistributing the bond pads over the entire surface of the die. Instead of wires, the die is attached to the substrate utilizing a direct solder connection. Although several steps and processes are eliminated when utilizing flip chip technology, there are several new problems that must be overcome. The main issue is the mismatch in the coefficient of thermal expansion (CTE) of the silicon die and the substrate. This mismatch will cause premature solder Joint failure. This issue can be compensated for by the use of an underfill material between the die and the substrate. Underfill helps to extend the working life of the device by providing environmental protection and structural integrity. Flux residues may interfere with the flow of underfill encapsulants causing gross solder voids and premature failure of the solder connection. Furthermore, flux residues may chemically react with the underfill polymer causing a change in its mechanical and thermal properties. As flip chip packages decrease in size, cleaning becomes more challenging. While package size continues to decrease, the total number of 1/0 continue to increase. As the I/O increases, the array density of the package increases and as the array density increases, the pitch decreases. If the pitch is decreasing, the standoff is also decreasing. This paper will present the keys to successful flip chip cleaning processes. Process parameters such as time, temperature, solvency, and impingement energy required for successful cleaning will be addressed. Flip chip packages will be cleaned and subjected to JEDEC level 3 testing, followed by accelerated stress testing. The devices will then be analyzed using acoustic microscopy and the results and conclusions reported.

• 한국항공우주학회지
• /
• 제39권6호
• /
• pp.481-486
• /
• 2011

결빙 관련 풍동 시험은 과냉각된 액적과 모델의 상사성을 고려하여 실제 크기 모델에 대해 풍동 시험이 이루어져야 하나 풍동 시험장의 공간적 제한으로 전기체에 대한 항공기 결빙은 제한적 혹은 항공기 구성품 단위별로 풍동 시험이 수행된다. 제한된 공간의 결빙 풍동 시험장에서 전기체 형상과 유사한 축적율과 결빙 영역을 조사하기 위해 본 연구에서는 일차적으로 실제 크기의 익형에 대해 Truncated Flapped 개념을 적용하였다. Flap의 변위각에 따른 압력 분포와 축적율의 경향성을 실제 크기의 익형과 Truncated Flapped 익형을 비교한 결과 정량적, 정성적으로 매우 유사한 경향을 나타냄을 확인하였다.

• 설비공학논문집
• /
• 제12권1호
• /
• pp.50-58
• /
• 2000

Experiments were carried out to obtain the effects of nozzle configuration and jet to jet spacing on the heat transfer characteristics of single line of circular water jets impinging on a constant heat flux plane surface. The nozzle configurations are Cone type, Reverse cone type and Vertical circular type, and the nozzle arrays are single jet(nozzle dia. 8 mm), 1 row of 3 jets and 1 row of 5 jets. Jet velocities ranging from 3m/s to 8m/s were investigated for the nozzle to target plate spacing of 80 mm. For the Cone and Reverse cone type nozzle arrays, the average Nusselt number of 1 row of 5 jets was larger than that of 1 row of 3 jets at Re$_{D}$<45000, but that of 1 row of 3 jets was larger than that of 1 row of 5 jets at $Reo\le45000$. For the Vertical circular type nozzle, however, the average Nusselt number of 1 row of 3 jets was larger than that of 1 row of 5 jets at all jet velocities. In the condition of fixed mass flow rates, the maximum heat transfer augmentation was obtained for 1 row of 5 jets and was over 2 times larger than that of the single jet for all nozzle configurations. The nozzle configurations that produce the maximum average Nusselt number are as follows: For 1 row of 3 jets, the Vertical circular type at $Reo\le45000$ and the Reverse cone type at $Reo\le45000$. But, they are the Reverse cone type at Re$_{D}$<55000 and the Vertical circular type at$Reo\le55000$ for 1 row of 5 jets.

• 설비공학논문집
• /
• 제12권1호
• /
• pp.59-66
• /
• 2000

In a previous paper, we have examined the effects of nozzle configuration and jet to jet spacing on the heat transfer of 1 row of circular water jets. In this paper, experiments have been conducted to obtain the effects of nozzle to target plate distances on the heat transfer of 1 row of 3 jets and 1 row of 5 jets. The nozzle configurations are Cone type, Reverse cone type and Vertical circular type. Nozzle to target plate distance H was varied from 16 mm(H/D=2) to 80mm(H/D=10). For fixed value of mass flow rate and nozzle to target plate distance, larger values of average Nusselt number were obtained for the smaller jet to jet spacing. For the array of water jets, the average heat transfer was decreased slightly with increasing nozzle to target plate distance at low jet velocity of $\textrm{V}_{o}$=3 m/s. However, except for $\textrm{V}_{o}$=8 m/s of 1 row of 5 jets, it was increased with increasing nozzle to target plate distance at high jet velocity of $\textrm{V}_{o}$$\geq$6m/s. We proposed to apply the nozzle configuration of maximum average heat transfer to each nozzle to target plate distance for 1 row of 3 jets, and, it was Reverse cone type nozzle for 1 row of 5 jets(Reynolds number$\geq$36000).