• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2015

In this paper, a 12-bit high resolution, power and area efficiency hybrid digital pulse width modulator (DPWM) with process and temperature (PT) calibration has been proposed for digital controlled DC-DC converters. The hybrid structure of DPWM combines a 6-bit differential tapped delay line ring-mux digital-to-time converter (DTC) schema and a 6-bit counter-comparator DTC schema, resulting in a power and area saving solution. Furthermore, since the 6-bit differential delay line ring oscillator serves as the clock to the high 6-bit counter-comparator DTC, a high frequency clock is eliminated, and the power is significantly saved. In order to have a simple delay cell and flexible delay time controllability, a voltage controlled inverter is adopted to build the deferential delay cell, which allows fine-tuning of the delay time. The PT calibration circuit is composed of process and temperature monitors, two 2-bit flash ADCs and a lookup table. The monitor circuits sense the PT (Process and Temperature) variations, and the flash ADC converts the data into a digital code. The complete circuits design has been verified under different corners of CMOS 0.18um process technology node.

• 보존과학연구
• /
• s.26
• /
• pp.127-139
• /
• 2005

We have conserved the sword with round pommel with a tri-ring which was excavated from No. 1 tomb of the Duckcheon-ri at the Gyeongju and requested from Jungang Research Center of the Cultural Heritage. When this artifact excavated, it was pressed flat state because of the influence of earth pressure and stuck to a gravel and soil laid scattered on the wooden coffin. If the artifacts is handled without plan, it can be damaged, therefore that sword was collected together with soil using the Polyurethane foam. After the artifact which had a weak specific and was collected using a this method can be safetly collected as below; First, we made the supporter of article ordered using a silicon and gypsum. The silicon can conserve the weak point of the artifact because it has a flexible and smooth properties and the gypsum can adhere closely to the artifact because it has a little expansion and shrinking but a hard and fluid characters. Consequently, gypsum is a good complement to the weak point of the silicon. Second, During a remove gauze and a reinforcing agent from the surface of a artifact which was reinforced using a acetone steam method. The acetone steam method can be supplement to a dangerous problem of acetonedircet method because this can be damaged in a surface of the artifact.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1997.10a
• /
• pp.39-45
• /
• 1997

Introduction : Polyimides are one of the most important classes of the high performance polymers due to their excellent electrical, thermal, and high-temperature mechanical properties. But their uses are limited because of their poor solubility. Most polyimide derivatives are processed in the form of polyamic acids, which are subsequently converted into the imide structures.Recently, it has been found that the soluble polyimides with large molecular weight sufficient to application. For enhancing processability, the majority of approaches have involved the following factors. As much as, the separation of the imide ring along the back-bone, that is to say, reducing the density of imide ring in the repeat structure. The introduction of bulky substituents along the back-bone, in order to enhance the free volume of main-chain. The incorporation of flexible or thermally stable linkages in the main-chain, reducing the packing force. The disruption of symmetry or recurrence regularity through copolymerization in order to reduce crystallnity.The objectives of this investigation are the synthesis and characterization of soluble polyimides as membrane materials by the single-step polymerization and the preparation of the asymmetric polyimide membrane by using phase inversion technique. In the present study, three series of polyimide derivatives are synthesized; H series is homopolyimides, A series is prepared from single dianhydride and two diamines, B series is yielded from two dianhydrides and a diamine. The dope solution was directly prepared from the PI solution via one step polymerization from monomers.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.9
• /
• pp.984-988
• /
• 2001

Since anti-angiogenesis could lead to the suppression of tumor growth, angiogenesis inhibitors have received particular attention for their therapeutic potential. In this study, two angiogenic inhibitors using the bioactive sequence from the kring le 5, AK1(KLYDY), AK2(KLWDF) were designed and synthesized. We have investigated their solution structures using NMR spectroscopy and their activities as angiogenesis inhibitors. AK2 has an intramolecular hydrogen bon d between the side chain amino proton of Lys1 and the carboxyl oxygen of Asp4 with a N ${\cdot}{\cdot}{\cdot}$O distance of $3.27\AA$, while AK1 shows more flexible structures than AK2. Indole ring in Trp is much bigger than the phenyl ring in Tyr and may have good face-to-edge interaction enforcing more rigid and constrained conformational features of AK2. Because of this relatively stable structure, Trp3 in AK2 may have better hydrophobic interaction with Phe5 than Tyr3 in AK1 if two adjacent aromatic groups are located in hydrophobic pocket of receptor. Since AK2 shows the similar anti-angiogenic activities to AK1, we are also able to confirm that the activity of AK1 is irrelevant to the Tyr phosphorylation. More rigid drug with higher activities can be provided by the mimetic approaches. For the further development of the angiogenesis inhibitors, these conformational studies on our lead peptides will be helpful in design of peptidomimetics.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.10
• /
• pp.995-999
• /
• 2015

Inductive sensors are versatile and economical devices that are widely used to measure a wide variety of physical variables, such as displacement, force, and pressure. In this paper, we propose a simple inductive sensor consisting of a thin partial ring and a coil set. The self-inductance of the sensor was estimated using magnetic circuit analysis and validated through finite element analysis (FEA). The natural frequency of the ring was estimated using Castigliano's theorem and the method of equivalent mass. The estimation was validated through experiments and FEA. A prototype sensor with a signal processing circuit is built and applied to noninvasively sense the pressure inside a flexible tube. The obtained sensor outputs show quadratic behavior with respect to the pressure. When fitted to a quadratic equation, the least-square measurement error was less than 2%. The results confirm the feasibility of pressure sensing using the proposed inductive sensor.

• Elastomers and Composites
• /
• v.51 no.3
• /
• pp.195-205
• /
• 2016

A series of aromatic poly(hydroxyamide)s (PHAs) containing varying oligo(oxyethylene) substituents and 1,3-phenylene imide ring unit in the main chain were synthesized by the direct polycondensation reaction. The inherent viscosities of the PHAs exhibited in the range of 0.89~1.12 dL/g in DMAc or DMAc/LiCl solution. The PH-2~5 copolymers were easily soluble in strong aprotic solvents: DMAc, NMP, DMSO etc. and the PH-5 copolymer was soluble in less polar solvents such as m-creasol and pyridine with LiCl salt on heating. However, all PBOs were quite insoluble in other solvents, but only partially soluble in sulfuric acid. All copolymers (PH-2~5) could afford the flexible and tough films by solution casting. We identified that the PHAs were converted to the PBOs by the thermal cyclization reaction in the range of $200{\sim}380^{\circ}C$. The 10% weight loss temperatures and char yields of the PBOs were recorded in the range of $382{\sim}647^{\circ}C$ and 38.7~73.1% values at $900^{\circ}C$. The tensile strength and initial modulus of the PH-5 in the copolmers showed the highest values of 2.46 GPa and 49.55 MPa, respectively. The LOI values of the PHAs were in the range 26.6~29.0%, and increased with increasing 1,3-phenylene imide ring unit.

• Journal of KIISE:Information Networking
• /
• v.31 no.3
• /
• pp.314-326
• /
• 2004

Bluetooth has been reputed as a wireless ad-hoc networking technology supplying scalable and extensible networks between digital devices. For that kind of networks, scatternet is a most essential part in bluetooth. But past researches on bluetooth scatternet has proposed only possibilities of scatternet algorithm based on simulation results. And many of the researches failed in guaranteeing extensibility and flexibility and had many difficulties in real hardware implementation. In this paper, we proposed node ring scatternet(NRS) algorithm guaranteeing extensible and flexible networks. NRS algorithm is designed for hardware implementation using real commercial bluetooth module. That algorithm is divided into initial formation and reformation. For initial formation, we proposed limited SEEK/SCAN algorithm. For reformation, we proposed DIAC algorithm and Reserved Recovery Node algorithm. And we proposed SFMP(Scatternet Formation ＆ Management Protocol) in protocol stack for real implementation. NRS algorithm is operated in SFMP. Finally, we performed real hardware experiments and evaluated the proposed algorithm. In that experiments, we succeeded in forming scatternet up to 20 nodes. In comparison with other similar algorithm, proposed algorithm have the improvement in scatternet formation delay and success rate.

• Biomolecules & Therapeutics
• /
• v.16 no.4
• /
• pp.425-430
• /
• 2008

The objectives of this study were to prepare PLGA film onto the surface of the capsular tension ring (CTR) for controlled drug release and investigate the influence of plasticizers, the test drug and measurement conditions on flexibility of the film. Film solutions were prepared by dissolving PLGA, plasticizer (triethyl citrate, TEC or polyethylene glycol, PEG), test drug (dexamethasone) in ethyl acetate then films were prepared by spray coating and evaporation method. Then, the flexibility of PLGA film was determined by elongation test. The addition of plasticizer, PEG or TEC to PLGA copolymer caused a depression of glass transition temperature ($T_g$) and the elasticity of PLGA films increased. The addition of dexamethasone to the PLGA/TEC matrix decreased the flexibility of film. Dimensional factors of the PLGA films such as width and thickness were significantly influenced on flexibility of films and film length and elongation speed had no considerable influence on elongation of films. In this study, sufficiently flexible and stable PLGA films capable of being coated onto CTR could be prepared. This PLGA films can be used as a platform for local drug delivery.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.630-634
• /
• 2010

The synthesis and ion binding properties of calix[4]pyrrole bearing pyrene moieties appended to one side of the calix[4]pyrrole are reported. The key feature is the presence of flexible fluorescence arms attached to the calix[4]pyrrole ring in a cis-fashion. The preliminary solution phase anion and cation binding studies revealed that the systems can be in fact as viable sensors for anionic guest.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.8
• /
• pp.1485-1490
• /
• 2008

Dumbbell-shaped aromatic amphiphilic molecules consisting of a dodeca-p-phenylene as a rigid segment and oligoether dendrons as a flexible chains were synthesized, characterized, and their aggregation behavior was investigated in the bulk and at the air-water interface. In contrast to the molecule 2 which shows a nematic liquid crystalline state, molecule 1 based on shorter dendritic chains was observed to self-assemble into a 3-D primitive orthorhombic supercrystal. And molecule 1 at the air-water interface was observed to reorganize from circular plates to ring structures by lateral compressions.