• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.163-168
• /
• 2020

We studied the change of photovoltaic properties of a flexible CuIn_xGa(_1-x)Se₂ (CIGS) solar cell fabricated on polyimide by mechanical bending with curvature radii of 75 mm (75R) and 20 mm (20R). The flexible CIGS cells were flattened on a PET film, then placed and forced against the surface of a curved block fabricated with pre-designed curvatures. Both up (compressive) and down (tensile) bending were applied to a specimen of CIGS on PET with curvatures of 75R and 20R for 10,000 times and 2,000 times, respectively. From J-V measurements, we found that the conversion efficiency (Eff.) was reduced by 3% and 4% for up-and down-bending, respectively, at curvature 75R; it was greatly reduced by 15% for curvature 20R in the up-bending. However, the open circuit voltage (V_oc) and short-circuit current density (J_sc) seemed to change little, within 3%, for the applied mechanical stresses. The degradation in Eff. resulted from the deterioration of the series (R_s) and shunt (R_sh) resistances of the solar cell.

• Journal of the Korea Convergence Society
• /
• v.13 no.3
• /
• pp.197-202
• /
• 2022

The CZTS solar cell is a thin film solar cell using an absorption layer composed of Cu, Zn, Sn, Se, and S, and is cheaper than a CIGS solar cell using In and Ga and more eco-friendly than a perovskite and CdTe solar cell using Pb and Cd. In this study, we conducted a bending test for flexible CZTS solar cells. Experiments were conducted in the direction of inner benidng with compressive stress and outer bending with tensile stress, and during the number of bending 1,000 times with a radius of curvature of 50 mmR, the efficiency of the solar cell decreased by up to 12.7%, and the biggest cause of efficiency reduction in both directions was a large decrease in parallel resistance.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1245-1248
• /
• 1996

This paper describes a cell programming environment that deals with problems associated with programming Flexible Manufacturing Cells(FMCs). The environment consists of the cell programming editor and the automatic generation module. In the cell programming editor, cell programmers can develop cell programs using task level description set which supports task-oriented specifications for manipulation cell activities. This approach to cell programming reduces the amount of details that cell programmers need to consider and allows them to concentrate on the most important aspects of the task at hand. The automatic generation module is used to transform task specifications into executable programs used by cell constituents. This module is based on efficient algorithm and expert systems which can be used for optimal path planning of robot operations and optimal machining parameters of machine tool operations. The development tool in designing the environment is an object-oriented approach which provides a simple to use and intuitive user interface, and allows for an easy development of object models associated with the environment.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.17 no.32
• /
• pp.63-71
• /
• 1994

The purpose of this paper is to describe an effective cell scheduling system for flexible manufacturing cells. Based on the FMC characteristics, cell scheduling can be defined as a dynamic modified flow shop working in a real-time system. This paper attempt to find the optimal cell scheduling when minimizing the mean flow time for n-job/m-machine problems in static and dynamic environments. Real-time scheduling in an FMC environment requires rapid computation of the schedule.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.84.1-84.1
• /
• 2010

Currently, new and renewable energy come into the spotlight, such as solar energy, wind power, fuel cell, hybrid car etc., due to the energy resource is being depleted. Especially, in order to solve like this problem, the study of solar cell manufacturing systems are being extensively researched such as vacuum process. But the major fault of the vacuum process are its expensive production price. On the order hand, Roll-to-roll printing system, the new technology of solar cell manufacturing, has low production price compare with the vacuum process. Also roll-to-roll printing system can decrease the 95% of waste water and 99.9% of harmful gasses than the vacuum process. So we addressed the roll to roll printing system for the flexible solar cell by using printing technology. This roll-to-roll printing system is comprised of various modules, such as web handling module, fine pattern printing module, dry/curing module, uniform coating module and laminating module etc.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.11
• /
• pp.104-108
• /
• 2012

Flexible organic thin film solar cell device with Bulk Hetero-Junction (BHJ) structure was fabricated with blended conjugated polymer of PCDTBT : $PC_{71}BM$ as active layer. Surface of ITO anode for the organic solar cell device was treated with ozone. The organic solar cell device with bare ITO showed short circuit current density ($J_{sc}$) of $8.2mA/cm^2$, open-circuit voltage ($V_{oc}$) of 0.73V, fill factor (FF) of 0.36, and power conversion efficiency (PCE) of 2.16%, respectively. The organic solar cell device with ozone treated ITO anode revealed distinctively improved performance parameters:$J_{sc}$ of $9.8mA/cm^2$, $V_{oc}$ of 0.82V, FF of 0.43, PCE(${\eta}$) of 3.42%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.403-403
• /
• 2011

결정질 태양전지는 태양전지 시장에 큰 서막을 장식하였다. 현재 여러 종류의 태양전지 기술들이 많이 나오고 있지만 결정질 태양전지는 변환 효율이 좋고 신뢰성이 높아서 높은 시장 점유율을 차지하고 있다. 하지만 응용 분야가 적고 기판 가격이 비싸다는 단점이 있다. 현재에는 응용분야 개선을 위하여 Flexible solar cell에 대한 연구가 활발하다. Flexible solar cell에 상부전극은 결정질 태양전지에서 사용되는 Ag나 Al 전극 대신 TCO 종류의 일종인 ITO를 많이 사용한다. Flexible Solar cell은 Organic Solar cell과 Amorphous Solar Cell 두 가지 범주를 가지고 있다. 본 연구에서는 Amorphous Solar Cell의 전극에 사용되는 ITO의 온도 Stress에 따른 특성을 연구함으로써 Engineer의 근본적인 이슈인 저비용, 고효율에 초점을 맞추어 소자특성을 확인해 보도록 한다. Glass에 E-beam evaporation 장비를 이용하여 ITO를 증착하였고 제작된 소자를 200, 250, 300, 350$^{\circ}C$의 온도변수를 두어 1시간동안 Annealing 하였다. 각 Annealing 온도에 따른 Sheet resistivity,와 visible 영역의 transmittant를 측정하였다. visible영역에서의 transmittant는 Annealing 200$^{\circ}C$에서 300$^{\circ}C$로 온도가 증가함에 따라 transmittant는 증가하다가 350$^{\circ}C$에서 감소하였다. Sheet resistivity의 경우 Annealing 200$^{\circ}C$에서 300$^{\circ}C$로 온도가 증가함에 따라 ITO의 Sheet resistivity가 줄어들다가 350$^{\circ}C$에서 증가하였다. 300$^{\circ}C$로 Annealing한 ITO가 가시광선 영역에서 transmittant가 가장 높은 80%로 측정 되었다. Sheet resistivity역시 300$^{\circ}C$로 Annealing한 ITO가 8${\Omega}/{\Box}$로 가장 낮았다. Annealing 온도가 ITO의 electrical 특성과 optical 특성에 변화를 주었음을 알 수 있었다. Resistivity가 낮은 ITO 전극으로 박막 셀을 제작한다면 좋은 효율을 얻을 수 있을 거라 생각된다.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.7
• /
• pp.126-136
• /
• 1997

This paper describes a task level cell programming environment that deals with difficulties in programming Flexible Manufacturing Cells (FMCs), and consists of the cell programming editor and the automatic generation module. In the cell programming editor, cell programs can be developed with task- oriented cell specifications that reduces the amount of details to be considered by cell programmers. The automatic generation module transforms task specifications into executable programs used by cell constituents. The development tool in designing the environment is an object-oriented approach which provides a simple to use and intuitive user interface, and allows for an easy development of object models associated with the environment. Test results are illustrated in order to demonstrate the applicability of the developed envifonment.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.711-714
• /
• 1998

본 논문에서는 wide data-width DRAM을 위한 flexible column redundancy scheme을 제안하였다. 구현된 redundancy scheme은 DB line shift method를 사용하여 wide data-width를 갖는 고집적 DRAM에 적용할 때 기존 redundancy scheme보다 더 작은 redundancy cell 면적과 fuse개수를 가지면서 더 큰 flexibility를 가지게 되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.233-233
• /
• 2007