• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.911-913
• /
• 2008

In this work, nonvolatile memory (NVM) devices for system on panel of flat panel display (FPD) were fabricated using low temperature polycrystalline silicon (LTPS) thin film transistor (TFT) technology with an oxide-nitride-oxynitride (ONOn) stack structure on glass. The results demonstrate that the NVM devices fabricated using the ONOn stack structure on glass have suitable switching characteristics for data storage with a low operating voltage, a threshold voltage window of more than 1.8 V between the programming and erasing (P/E) states after 10 years and its initial threshold voltage window (${\Delta}V_{TH}$) after $10^5$ P/E cycles.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.225-228
• /
• 2002

Supersonic jet impingement on a flat plate has been investigated to show the flow physics for different jet heights and to demonstrate the adequacy of the characteristics-based flux-difference Wavier-Stokes code Current study also compares the steady-state solutions obtained with variable CFL number for different grid spacing with the time-accurate unsteady solutions using the inner iterations, displaying a good agreement between the two sets of numerical solutions. The unsteady nature of wall fluctuations due to bouncing of the plate shock is also uncovered for high pressure ratios. The methodology is then applied to a complex vertical launcher system where the jet plume hits the bottom wail, deflects into the plenum and eventually exits through the vertical uptake. Flow structures within vertical launcher system are captured and solutions are partially verified against the flight test data. Present jet impingement study thus shows the usefulness of CFD in designing a complex structure and predicting flow behavior within such a system.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.55-58
• /
• 2005

From the development of residential flat plate system, continuously bended shear reinforcements were applied in the joint performance test. The testing parameters are shear reinforcement types, which are no reinforcement, studrail reinforcement, and rebar type reinforcement. To verify the lateral resisting capacity, cyclic load is applied in the constant vertical load condition. From the test results, the resisting capacity of developed shear reinforcement system has a good performance behavior in the story drift ratio.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.2
• /
• pp.29-33
• /
• 2008

LCD panels are increasingly used to show moving image material, for example in LCD television sets. However, moving images become blurred on LCD panels. One of the causes of motion blur is the slow reaction of LC(liquid crystal) cell to change in the pixel value. Another cause of motion blur is the hold-type characteristic of the LCD panel, during the frame time the image is shown continuously. This type of motion blur can be reduced with a scanning backlight. We have designed and fabricated a scanning backlight system that solves the hold-type characteristic problem in a way that Flat fluorescent lamp divided 6 blocks was scanned 60Hz.

• Current Optics and Photonics
• /
• v.8 no.4
• /
• pp.375-381
• /
• 2024

In this report, we present the design, fabrication, and experiment of a static solar system for electric vehicle (EV) applications. The static concentration component is composed of compound parabolic concentrators (CPCs) couplings with multi-junction solar cells, where a flat silicon panel is added to the bottom of the CPV structure to maximize power generation. This design allows the system to collect both direct sunlight and diffused sunlight. The CPCs were fabricated with acrylic with a geometric concentration ratio of 4×. We built a prototype with a (3 × 3) cell array of CPCs with a thickness of 25 mm, which is as thin as conventional flat photovoltaic panels, and performed an outdoor experiment that showed that after six hours of operation, the system had an acceptance angle of approximately 43° and an average daily efficiency of 22.85%.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.849-853
• /
• 2012

Generally, it is not easy to learn guitar fingering for beginner. In this paper, therefore, we attach LED to flat board of guitar to more easily teach the beginner and also implement LED control system that can connect ATmega 128 in order to drive LED attached to guitar. The guitar's flat board is connected with ATmega 128 as communication method of Zigbee. We also develop UI that easily can be learned code and playing for guitar, programmed by guitar fingering and perform the research for guitar fingering using LED.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.485-487
• /
• 1994

A novel control scheme for a Switched Reluctance Motor(SRM) drive is described. The control scheme which is to increase torque, to decrease torque ripples and easy to commutate is suggested. The conditions for high torque drive which includes flat-topped phase current and voltage control arc analyzed and adopted in this control scheme. Flat-topped current is achived via dc-link voltage control. The suggested control system was tested to verify this suggestion.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.7
• /
• pp.833-841
• /
• 2007

The aim of this paper is to analyze the conjugate problems of heat conduction in solid walls coupled with laminar free convection flow adjacent to a vertical flat plate under boundary layer approximation. Using the similarity transformations the governing boundary layer equations for momentum and energy are reduced to a system of partial differential equations and then solved numerically using Finite Difference Method(FDM) known as the Keller-box scheme. Computed solutions to the governing equations are obtained for a wide range of non-dimensional parameters that are present in this problem, namely the coupling parameter P. the Prandtl number Pr and the heat generation parameter Q. The variations of the local heat transfer rate as well as the interface temperature and the friction along the plate and typical velocity and temperature profiles in the boundary layer are shown graphically. Numerical solutions have been consider for the Prandtl number Pr=0.70

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2006.05a
• /
• pp.231-234
• /
• 2006

과거 디스플레이 장치로서 사용되던 CRT를 대신하여, 상대적으로 두께가 않고 가벼운 영상장치인 평판 디스플레이(Flat Panel Display, FPD)의 사용이 급증하고 있다. 이렇게 평판표시장치(Flat Panel Display) 산업의 폭발적인 성장과 함께 새로운 공정개발을 통해 짧은 시간에 더 많은 양을 생산하고, 불량률을 낮추는가에 생산업체의 사활이 달려있다. 본 논문은 FPD 공정에서 품질을 결정하는 여러 요인 가운데 비중이 큰 박막 두께의 제어를 지능화 알고리즘을 통해 해결하고자 한다. 이는 불필요한 과정을 줄여 공정경비를 절감 및 소요시간을 단축하고, 정밀하게 두께를 측정하는 것을 가능하게 한다. 마지막으로, 제안한 알고리즘을 광 간섭 두께 측정기를 통해 얻은 실제 값을 가지고 시료의 두께를 측정한다.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.160-165
• /
• 1998

This paper describes a method for field analysis inside the flat-type brushless DC motor using 2-D field simulator. Rigorous field analysis entail 3-D analysis. However, this analysis is not often appropriate for system designs because of the time and cost involved. For field analysis in this study, the 3-D problem is reduced to a 2-D boundary value problem by introducing a cylindrical cutting plane at the mean radius of the magnets. Independent of sizes and shapes of systems, the exact 2-D field results can be obtained with reasonable predictability.