• Land and Housing Review
• /
• v.4 no.4
• /
• pp.371-382
• /
• 2013

This study performs an experimental investigation to evaluate the behavior of RC flat plate interior joints specimens. Three 60 percent scale Flat Plate interior specimens assemblies representing a portion of a Flat Plate Apartment Structural System subjected to simulated seismic loading (unbalanced moments) under constant axial load were tested, including one specimens with ordinary shear reinforcement and two specimens with folded bend type shear reinforcement. Test results are shown that (1) the design code KBC 2009 is accurate estimate the behavior of specimens. (2) Two types shear reinforcement have a similar structural behavior, but construction work of rebar with folded bend type shear reinforcement is easier than that of ordinary shear reinforcement. (3) In moderate seismic region, RC Flat Plate interior joint with folded bend type shear reinforcement is apply to structural design of Flat Plate.

• The Journal of Korean Physical Therapy
• /
• v.25 no.5
• /
• pp.297-302
• /
• 2013

Purpose: This study was conducted in order to investigate the kinematic gait parameter of lower extremities with different gait conditions (level walking, stair, ramp) in hemiplegic patients. Methods: Ten hemiplegic patients participated in this study and kinematic data were measured using a 3D motion analysis system (LUKOtronic AS202, Lutz-kovacs-Electronics, Innsbruk, Austria). Statistical analysis was performed using one-way repeated measure of ANOVA in order to determine the difference of lower extremity angle at each gait phase with different gait conditions. Results: Affected degree of ankle joint in the heel strike phase showed significant difference between level walking and climbing stairs, and toe off phase showed significant difference between level walking and climbing stairs, ramps, and climbing stairs. Affected degree of knee joint showed no significant difference in all attempts. Affected degree of hip joint in the toe off phase showed significant difference between level walking, ramps and stairs, and climbing ramps. Swing phase showed significant difference between sides for level walking and stairs, climbing ramps. Affected ankle joint of heel strike and toe off, and affected hip joint of toe off and the maximum angle of swing phase in the angle was increased. Unaffected side of the ankle joint, knee joint, and hip joint showed a significant increase in walking phase. Conclusion: These findings indicate that compared with level walking, different results were obtained for joint angle of lower extremity when climbing stairs and ramps. In hemiplegia patient's climbing ramps, stairs, more movement was observed not only for the non-affected side but also the ankle joint of the affected side and hip joint. According to these findings of hemiplegic patients when climbing stairs or ramps, more joint motion was observed not only on the unaffected side but also on the affected side compared with flat walking.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.308-315
• /
• 2008

극저온 유체를 운반하는 선박의 화물창은 보통 1차 방벽과 2차 방벽으로 구성되어 있다. 1차 방벽에 소량의 극저온 유체의 누출이 생기더라도, 액밀이 되는 2차 방벽에서 추가적인 극저온 유체의 누출을 방지할 수 있기 때문이다. 그러나 2차 방벽에 추가적인 손상이 생길 경우 유리솜으로 만들어진 Flat Joint를 거쳐 선체내벽까지 극저온 유체에 노출될 가능성이 있게 된다. 본 연구의 관심사는 2차 방벽의 손상 정도에 따라, 그리고 누출되는 극저온 유체의 양에 따라, 내측선체에 얼마나 영향이 미치는가를 알아보는 것이다. 이를 위해 본 연구에서는 극저온 유체를 운반하는 선박의 화물창을 구성하는 2차 방벽에 구멍을 뚫어 Flat Joint 사이로 극저온 유체가 흘러 들어가도록 격자를 생성한 후, CFD 소프트웨어를 이용하여 극저온 유체의 누출에 대한 계산을 수행 하였으며 이를 실험 결과와 비교 분석 하였다. 실험과 계산 결과를 살펴보면, 극저온 유체량에 따라 내측 선체에의 피해를 최소화 할 수 있음을 확인하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.308-315
• /
• 2008

극저온 유체를 운반하는 선박의 화물창은 보통 1차 방벽과 2차 방벽으로 구성되어 있다. 1차 방벽에 소량의 극저온 유체의 누출이 생기더라도, 액밀이 되는 2차 방벽에서 추가적인 극저온 유체의 누출을 방지할 수 있기 때문이다. 그러나 2차 방벽에 추가적인 손상이 생길 경우 유리솜으로 만들어진 Flat Joint를 거쳐 선체내벽까지 극저온 유체에 노출될 가능성이 있게 된다. 본 연구의 관심사는 2차 방벽의 손상 정도에 따라, 그리고 누출되는 극저온 유체의 양에 따라, 내측선체에 얼마나 영향이 미치는가를 알아보는 것이다. 이를 위해 본 연구에서는 극저온 유체를 운반하는 선박의 화물창을 구성하는 2차 방벽에 구멍을 뚫어 Flat Joint 사이로 극저온 유체가 흘러 들어가도록 격자를 생성한 후, CFD 소프트웨어를 이용하여 극저온 유체의 누출에 대한 계산을 수행 하였으며 이를 실험 결과와 비교 분석 하였다. 실험과 계산 결과를 살펴보면, 극저온 유체량에 따라 내측 선체에의 피해를 최소화 할 수 있음을 확인하였다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.2
• /
• pp.257-269
• /
• 1996

The puropose of this study was to investigate the movement-fitness according to the surface changing of lower limb The experimental items were divided into the lower limb movements (5) and body-shapes (7). This study was done by the expansion and contraction rate consideration of length, girth Also, the lower half of body shape-change on the movements and body-shapes by flat shell was done simultaneously. The summarized findings resulted from experiments and investigation are suggested as follows; First, when commpared the expansion and contraction rate of the length and girth items, the expansion rate of the back crotch length (14~20%), hip girth (10~ 21%) and knee girth (6.2~18.5%) in rabbit leap movement was the most notable among all variables considered in this experimentation. On the others hand, the front croth length (-22~-52%) contracted remarkably. And big-thigh type was the most notable on the body-shape comparision. Second, in comparision of the expansion and contraction rate of the area on the blocks, the expansion of the hip (50~200%) and knee (51~74%) block was the most remarkable. Especially, in the sit on knees movement of the hip-down type expanded 209.4%. Third, in comparision of the lower half of body shape-change, on the movements and body- shapes by the flat shell, under the influence of knee-joint and hip-joint the shape-changs of the hip and knee block was the most notable. But the shape-change of the waist, abdomen, calf, and ankle was feeble.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.32-40
• /
• 1997

Solid state diffusion bonding is the joining process performed by creep and diffusion, which is accelerated by heating below melting temperature and proper pressing, in vacuum or shielding gas atmosphere. By this process we can obtain sufficient joint which can't be expected from the fusion welding. For Ti-6Al-4V alloy, the optimum solid state diffusion bonding condition and mechanical properties of the joint were found, and micro void morphology at bond interface was observed by SEM. The results of tensile test showed sufficient joint, whose mechanical properties are similar to that of base metal. 850$^{\circ}$C, 3MPa is considered as the optimum bonding condition. Void morphology at interface is long and flat at the initial stage. As the percentage of bonded area increases, however, small and round voids are found. Variation of void shape can be explained as follows. As for the void shrinkage mechanism, at the initial stage, power law creep is the dominant, but diffusion mechanism is dominant when the percentage of bonded area is increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• v.y2004m10
• /
• pp.1-6
• /
• 2004

We ensure a flat and regular basic surface by using part of joint waterproofing improved sheet method applying the upper slab of a concrete structure. We solve the problem of getting loose scale the general sheet by waterproofing of the sheet and improving adhesive strength of the basic concrete. Also, waterproofing sheet union to problem of joint have solved using of insertion type method so that, it improved a watertightness. It has improved in resist impact, resist abrasion and it is the effect of shortened construction period and cutting down on construction expenses. Here are the special quality and superiority of this waterproofing research. (1) Level material has the super adhesive strength so that it makes the basic surface without the gab of waterproofing sheet and waterproofing layer with the string adhesive strength. (2) We unite the sheet with the joining part between sheets by waterproofing sheet joint using of method. (3) There is the effect of shortened construction period and cutting down on construction expenses without waterproofing of protection.

• Journal of the Korea Convergence Society
• /
• v.11 no.6
• /
• pp.393-400
• /
• 2020

This study used a three-dimensional motion analysis system for 15 elite tennis players (male 8, female7) to identify the relevance of scapula movement to shoulder pain. During the flat serve, the angular velocity and joint moment of scapula anterior/posterior tilt, downward/upward rotation, internal/external rotation were calculated and this was compared between groups. As a result, the maximum angular velocity for the anterior and posterior tilt tended to be higher in control group(CG) than in the shoulder pain group(SPG), and the maximum angular velocity for internal and external rotation in all phases except the follow-through phase was higher than that of CG. The maximum moment for the anterior and posterior tilt in the late coking phase was statistically significantly higher than that of SPG, the joint moment for the downward and upward rotation of the coking phase was statistically significantly lower than that of CG, and the moment for the internal and external rotation, the SPG was found to be lower than that of CG in the whole phases.

• The Journal of Korean Physical Therapy
• /
• v.34 no.4
• /
• pp.161-167
• /
• 2022

Purpose: The purpose of this study was to investigate the effects of regular training on the uneven surface that stroke patients encounter in their daily life on their ankle joint muscle activity and balance ability. They were divided into two groups: the gait training group on uneven surfaces and the gait training group on normal surfaces. Methods: In this study, 30 patients diagnosed with stroke and undergoing rehabilitation were selected. 15 people in the uneven surface gait training group and 15 people in the flat gait training group were selected. The muscle activation of the ankle muscles was measured when walking again on a even surface after walking on an uneven surface and on a flat ground. After each gait training, the limit of stability and Romberg test were performed to evaluate the balance ability. Results: As a result of the experimental results before and after walking by group, the tibialis anterior muscle activity of the paralyzed side was significantly decreased in the uneven surface walking group. As a result of measuring balance ability after training, the limit of stability in all directions was significantly increased in the uneven surface gait training group, and the area and length moved significantly decreased in the uneven surface gait training group in the Romberg test as well (p<0.05). Conclusion: After walking on uneven surface, it was confirmed that the muscle activity of the ankle joint decreased in normal flat walking, and thus the efficiency of muscle activity was increased. In addition, it was possible to confirm the improvement of the balance ability of the gait training on the uneven surface, and in conclusion, it could be confirmed that it had an effect on the improvement of the walking ability.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.74-80
• /
• 2008

This paper evaluates seismic capacities of slab-column joints in flat plate system which has columns with various aspect ratio as experimental parameters. Continuous - bended shear reinforcements were applied for the prevention of punching shear failure in this study. The specimens of FIS1-05, FIS1-10, and FIS1-20 have the aspect ratio of 0.5, 1.0, and 2.0 respectively. Static lateral force was applied to the specimens in a horizontal direction and vertical load was applied by constant gravity load ratio. The test results were evaluated by lateral displacement and strength of slab-column joint. Consequently, the lateral resisting capacity of rectangular type column such as FIS1-05, FIS1-20 is superior to the square type column such as FIS1-10.