• Structural Engineering and Mechanics
• /
• v.87 no.1
• /
• pp.47-56
• /
• 2023

Any pre-existed delamination defect present during manufacturing or induce during service loading conditions in the wingskin adherend invariably shows a greater loss of structural integrity of the spar wingskin joint (SWJ). In the present study, inter-laminar delamination propagation at the critical location of the SWJ has been carried out using contact and multi-point constraint finite elements available with commercial FE software (ANSYS APDL). Strain energy release rates (SERR) based on virtual crack closure technique have been computed for evaluation of the opening (Mode-I), sliding (Mode-II) and cross sliding (Mode-III) modes of delamination by sequential release of multi point constraint elements. The variations of different modes of SERR are observed to be significant by considering varied delamination lengths, material properties of adherends and radius of curvature of the SWJ panel. The SERR rates are seen to be much different at the two pre-embedded delamination ends. This shows dissimilar delamination propagation rates. The maximum is seen to occur in the delamination front in the unstiffened region of the wingskin. The curvature geometry and material anisotropy of SWJ adherends significantly influences the SERR values. Increase in the SERR values are observed with decrease in the radius of curvature of wingskin panel, keeping its width unchanged. SWJs made with flat FRP composite adherends have superior resistance to delamination damage propagation than curved composite laminated SWJ panels. SWJ made with Boron/Epoxy (B/E) material shows greater resistance to the delamination propagation.

• Computers and Concrete
• /
• v.32 no.5
• /
• pp.465-474
• /
• 2023

The point load test (PLT) is a widely-used alternative method in the field to determine the uniaxial compressive strength due to its simple testing machine and procedure. The point load test index can estimate the uniaxial compressive strength through conversion factors based on the rock types. However, the mechanism correlating these two parameters and the influence of the mechanical properties on PLT results are still not well understood. This study proposed a theoretical model to understand the mechanism of PLT serving as an alternative to the UCS test based on laboratory observation and literature survey. This model found that the point load test is a self-confined compression test. There is a compressive ellipsoid near the loading axis, whose dilation forms a tensile ring that provides confinement on this ellipsoid. The peak load of a point load test is linearly positive correlated to the tensile strength and negatively correlated to the Poisson ratio. The model was then verified using numerical and experimental approaches. In numerical verification, the PLT discs were simulated using flat-joint BPM of PFC3D to model the force distribution, crack propagation and BPM properties' effect with calibrated micro-parameters from laboratory UCS test and point load test of Berea sandstones. It further verified the mechanism experimentally by conducting a uniaxial compressive test, Brazilian test, and point load test on four different rocks. The findings from this study can explain the mechanism and improve the understanding of point load in determining uniaxial compressive strength.

• The Journal of Korean Physical Therapy
• /
• v.9 no.1
• /
• pp.127-145
• /
• 1997

The purpose of this study wa9 to analyse the gait patterns of two female children with hemiplegic cerebral palsy by using the three-dimensional video motion analysis technique. Case 1 has mild spastic hemiplegia on the right side while Case 3 has moderate spastic hemiplegia on the left side. A group of 10, normal female children of the same age(7-8 years old) were selected as the control group for comparison. Time and distance variables as well as the Center of Mass displacement, and the pelvic and joint motions in three anatomical planes were analysed for this purpose. The following observations were made through the analysis : Case 1 revealed an asymmetrical gait pattern in which the step length of the unaffected side was shorter than that of the affected side, which wan a result of the effort to minimize loading on the affected leg by shortening the swing phase of the unaffected leg. Case 1 scored similar phase ratios, cadence and walking velocity to the normal group. A slight posterior tilt of the pelvis was observed throughout the gait cycle. Less hip and knee flexion than the normal group was observed, and demonstrated hyperextension of the knee in the terminal stance phase. The main problem in case 1 originated from the insufficient dorsiflexion of the affected foot during the swing phase. Therefore, Case 1 has difficulty with foot clearance in the swing phase. Usually, this is compensated for by using exessive hip abduction and medial rotation in conjuction with trunk elevation as well as increased vortical displacement of the center of mass. Case 1 revealed a foot-flat initial contact pattern. Case 2 was characterized by a consistent retraction ef the affected aide of the body througout the gait cycle, As a result, an asymmetrical gait pattern with increased stance phase ratios of the unaffected side was observed. In spite of this the step lengths of both sieds were similar. Case 2 scored lower cadence and walking speed than the normal group with lower gait stability. The main problem in Case 2 originated from an excessive plantaflexion of the affected foot which, in turn, rebutted in high hip and knee flexion. Hyperextension of the knee was observed at mid-stance, and execessive anterior tilt of the pelvis throughout the gait cycle was noticed. A gait pattern with high hip abduction and medial circumduction was maintained for the stability in the stance phase and foot clearance in the swing phase. Case 2 revealed a forefoot-contact initial contact pattern.

• The Journal of the Korean life insurance medical association
• /
• v.25
• /
• pp.9-24
• /
• 2006

지속적으로 증가 하고 있는 악성 종양 발병률의 증가, 생존률의 향상, 조기발견의 증가 등이 암 기왕자의 보험 수요 상승을 가져오고 있으며, 보험시장에서 더 이상 암 기왕자를 도외시하기 어렵게 만들고 있다. 그러나, 현재 국내에서는 암 기왕자를 인수할 수 있는 상품과 언더라이팅 인수 기법이 부족한 실정이다. 본 논문은 이러한 상황 하에서 기존에 거절체로 인식되었던 암 기왕자의 적극적인 인수를 위해 악성종양에 대한 보험 의학적인 고찰과 사망률, 위험도에 대해 분석하고, 국내에서 암 기왕자의 보험 인수 시 문제점과 그 해결방안을 모색해 보았다. 종양은 종양세포의 성장과 확산의 정도를 나타내는 병기와 조직학적 등급에 의해 그 예후와 경과가 예측 가능하며, 이 병기를 표준화하려는 국제적 시도로 1977년 American Joint Committee on Cancer(AJCC)는 TNM system 을 제시하였다. 병기를 기초로 치료의 결정도 함께 이루어지는데, 주요 치료법을 수술, 방사선치료, 항암치료, 면역요법이 있다. 이러한 치료법들은 후기 부작용을 일으키거나 이차성 암(Secondary malignant neoplasm)의 원인이 되기도 한다. 병기에 따른 암환자의 사망률을 살펴 보면, 암은 일정시기 동안 사망률이 급격히 증가하다가 이후에 점차 사망률이 감소하고, 그 이후에는 사망률에 영향을 미치지 않는다. 이러한 사망률 변화의 특성은 암 기왕자에게 평준식 정액 할증법(Per mille flat extra)의 적용이 적절함을 보여준다. 그러나, 현재 국내에서는 악성 종양 기왕자를 위한 상품이 전무한 상태이며, 암의 병리적 병기와 치료에 관련된 정보를 얻을 수 있는 도구도 부족하고, 명확한 인수 기법이 없다. 또한, 자체의 경험통계의 부족으로 위험에 대한 부담감이 큰 것이 현실이다. 하지만, 병기에 따른 사망률의 변화에서도 알 수 있듯이 평준식 정액 할증법의 도입이나, 악성종양의 병기(Stage)별 정액 할증률을 삭감법으로 전환하는 기준을 개발한다면, 종신보험은 충분히 인수가 가능하다. 또한, CI 보험도 암에 대한 부담보를 하는 선진사의 인수 기법을 도입하거나, 암 기왕자만을 위한 CI 상품을 개발하는 등 새로운 인수 기법을 모색한다면, 암기왕자 인수의 폭은 넓어질 것이다. 이와 같은 노력과 함께, 언더라이팅의 정보 획득을 위한 암 기왕자만의 고지서를 개발하고, 전문 언더라이터의 양성을 위한 노력을 게을리 하지 않는다면, 암기왕자를 적극적으로 인수할 수 있을 것이다. 앞으로 국내 보험사가 위와 같은 노력을 지속적으로 해 나가고, 비교적 예후와 경과가 양호한 0기와 1기 암 기왕자부터 단계적으로 종신보험의 인수를 시도한다면, 비교적 안전하게 경험치를 축적할 수 있을 것이다. 뿐만 아니라 국내 보험업계는 새로운 시장의 확보와 보험에 대한 대외 이미지 개선이라는 효과도 함께 얻게 될 것이다.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.4
• /
• pp.1693-1697
• /
• 2012

Objective: To explore the effect on radiosensitivity of arsenic trioxide ($As_20_3$) in conjunction with hyperthermia on the esophageal carcinoma EC-1 cell line. Method: Inhibition of EC-1 cell proliferation at different concentrations of $As_20_3$ was assessed using the methyl thiazolyl blue colorimetric method (MTT method), with calculation of $IC_{50}$ value and choice of 20% of the $IC_{50}$ as the experimental drug concentration. Blank control, $As_20_3$, hyperthermia, radiotherapy group, $As_20_3$ + hyperthermia, $As_20_3$ + radiotherapy, hyperthermia + radiotherapy and $As_20_3$ + hyperthermia + radiotherapy groups were established, and the cell survival fraction (SF) was calculated from flat panel colony forming analysis, and fitted by the 'multitarget click mathematical model'. Flow cytometry (FCM) was used to detect changes in cell apoptosis and the cell cycle. Results: $As_20_3$ exerted inhibitory effects on proliferation of esophageal carcinoma EC-1 cells, with an $IC_{50}$ of 18.7 ${\mu}mol/L$. After joint therapy of $As_20_3$ + hyperthermia + radiotherapy, the results of FCM showed that cells could be arrested in the $G_2$/M phase, and as the ratio of cells in $G_0/G_1$ and S phases decreased, cell death became more pronounced. Conclusion: $As_20_3$ and hyperthermia exert radiosensitivity effects on esophageal carcinoma EC-1 cells, with synergy in combination. Mechanistically, $As_20_3$ and hyperthermia mainly influence the cell cycle distribution of EC-1 esophageal carcinoma cells, decreasing the repair of sublethal damage and inducing apoptosis, thereby enhancing the killing effects of radioactive rays.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.3
• /
• pp.295-313
• /
• 2006

Statement of problem. Higher fracture rates were reported for Branemark implants placed in the maxilla and for 3.75 mm diameter implants installed in the posterior region. Purpose. The purpose of this study was to investigate the fracture of a fixture by finite element analysis and to compare different diameter of fixtures according to the level of alveolar bone resorption. Material and Methods. The single implant and prosthesis was modeled in accordance with the geometric designs for the 3i implant systems. Models were processed by the software programs HyperMesh and ANSA. Three-dimensional finite element models were developed for; (1) a regular titanium implant 3.75 mm in diameter and 13 mm in length (2) a regular titanium implant 4.0 mm in diameter and 13 mm in length (3) a wide titanium implant 5.0 mm in diameter and 13 mm in length each with a cementation type abutment and titanium alloy screw. The abutment screws were subjected to a tightening torque of 30 Ncm. The amount of preload was hypothesized as 650 N, and round and flat type prostheses were 12 mm in diameter, 9 mm in height were loaded to 600 N. Four loading offset points (0, 2, 4, and 6 mm from the center of the implants) were evaluated. To evaluate fixture fracture by alveolar bone resorption, we investigated the stress distribution of the fixtures according to different alveola. bone loss levels (0, 1.5, 3.5, and 5.0 mm of alveolar bone loss). Using these 12 models (four degrees of bone loss and three implant diameters), the effects of load-ing offset, the effect of alveolar bone resorption and the size of fixtures were evaluated. The PAM-CRASH 2G simulation software was used for analysis of stress. The PAM-VIEW and HyperView programs were used for post processing. Results. The results from our experiment are as follows: 1. Preload maintains implant-abutment joint stability within a limited offset point against occlusal force. 2. Von Mises stress of the implant, abutment screw, abutment, and bone was decreased with in-creasing of the implant diameter. 3. With severe advancing of alveolar bone resorption, fracture of the 3.75 and the 4.0 mm diameter implant was possible. 4. With increasing of bending stress by loading offset, fracture of the abutment screw was possible.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.1-8
• /
• 2006

The purpose of this study was to evaluate normalized jerk according to shoes, slope, and velocity during walking. Eleven different test subjects used three different types of shoes (running shoes, mountain climbing boots, and elevated forefoot walking shoes) at various walking speeds(1.19, 1.25, 1.33, 1.56, 1.78, 1.9, 2, 2.11, 2.33m/sec) and gradients(0, 3, 6, 10 degrees) on a treadmill. Since there were concerns about using the elevated forefoot shoes on an incline, these shoes were not used on a gradient. Motion Analysis (Motion Analysis Corp. Santa Rosa, CA USA) was conducted with four Falcon high speed digital motion capture cameras. Utilizing the maximum smoothness theory, it was hypothesized that there would be differences in jerk according to shoe type, velocity, and slope. Furthermore, it was assumed that running shoes would have the lowest values for normalized jerk because subjects were most accustomed to wearing these shoes. The results demonstrated that elevated forefoot walking shoes had lowest value for normalized jerk at heel. In contrast, elevated forefoot walking shoes had greater normalized jerk at the center of mass at most walking speeds. For most gradients and walking speeds, hiking boots had smaller medio-lateral directional normalized jerk at ankle than running shoes. These results alluded to an inverse ratio for jerk at the heel and at the COM for all types of shoes. Furthermore, as velocity increased, medio-lateral jerk was reduced for all gradients in both hiking boots and running shoes. Due to the fragility of the ankle joint, elevated forefoot walking shoes could be recommended for walking on flat surfaces because they minimize instability at the heel. Although the elevated forefoot walking shoes have the highest levels of jerk at the COM, the structure of the pelvis and spine allows for greater compensatory movement than the ankle. This movement at the COM might even have a beneficial effect of activating the muscles in the back and abdomen more than other shoes. On inclines hiking boots would be recommended over running shoes because hiking boots demonstrated more medio-lateral stability on a gradient than running shoes. These results also demonstrate the usefulness of normalized jerk theory in analyzing the relationship between the body and shoes, walking velocity, and movement up a slope.

• Spatial Information Research
• /
• v.11 no.2
• /
• pp.101-117
• /
• 2003

High resolution satellite image analysis has been recognized as an effective technique for monitoring local land-cover and atmospheric changes. In this study, a new high resolution map for land-cover was generated using both high-resolution IKONOS image and conventional land-use mapping. Fuzzy classification method was applied to classify land-cover, with minimum operator used as a tool for joint membership functions. In separateness analysis, the values were not great for all bands due to discrepancies in spectral reflectance by seasonal variation. The land-cover map generated in this study revealed that conifer forests and farm land in the ground and tidal flat and beach in the ocean were highly changeable. The kappa coefficient was 0.94% and the overall accuracy of classification was 95.0%, thus suggesting a overall high classification accuracy. Accuracy of classification in each class was generally over 90%, whereas low classification accuracy was obtained for classes of mixed forest, river and reservoir. This may be a result of the changes in classification, e.g. reclassification of paddy field as water area after water storage or mixed use of several classification class due to similar spectral patterns. Seasonal factors should be considered to achieve higher accuracy in classification class. In conclusion, firstly, IKONOS image are used to generated a new improved high resolution land-cover map. Secondly, IKONOS image could serve as useful complementary data for decision making when combined with GIS spatial data to produce land-use map.

• Nuclear Engineering and Technology
• /
• v.42 no.6
• /
• pp.662-669
• /
• 2010

To develop the manufacturing methods for the blanket first wall (FW) of the International Thermonuclear Experimental Reactor (ITER) and to verify the integrity of the joint, Be/Cu mockups were fabricated and tested at the KoHLT-1 (Korea Heat Load Test facility), a graphite heater facility located at the Korea Atomic Energy Research Institute (KAERI). Since Be and Cu joining is the focus of the present study, the fabricated mockups had a CuCrZr heat sink joined with three Be tiles as an armor material, unlike the original ITER blanket FW, which has a stainless steel structure and coolant tubes. Hot isostatic pressing (HIP) was carried out at $580^{\circ}C$ and 100 MPa for 2 hours as the method for Be/Cu joining. Three interlayers, namely, $1{\mu}mCr/10{\mu}mCu$, $1{\mu}mTi/0.5{\mu}mCr/10{\mu}mCu$, and $5{\mu}mTi/10{\mu}mCu$ were applied as a coating to the Be tiles by a physical vapor deposition (PVD) method. A shear test was performed with the specimens, which were fabricated by the same methods as those used to fabricate the mockups. The average values were 125 MPa to 180 MPa, and the samples with the $1{\mu}mCr/10{\mu}mCu$ interlayer showed the lowest value. No defect or delamination was found in the joints of the mockups by the developed ultrasonic test using a flat-type probe with a 10 MHz frequency and a 0.25 inch diameter. High heat flux (HHF) tests were performed at $1.0\;MW/m^2$ heat flux for each mockup using the given conditions, and the results were analyzed by ANSYS-CFX code. For the test criteria, an expected fatigue lifetime about 1,000 cycles was obtained by analysis with ANSYS-mechanical code. Mockups using the interlayers of $1{\mu}mTi/0.5{\mu}mCr/10{\mu}mCu$ and $5{\mu}mTi/10{\mu}mCu$ survived up to 1,100 cycles over the required number of cycles. However, one of the Be tiles in the other two mockups using the $1{\mu}mCr/10{\mu}mCu$ interlayer was detached during the screening test, and others were detached by discharge after 862 cycles. The integrity of the joints using the proposed interlayers was proven by the HHF test, but the other interlayer requires more study before it can be used for the joining of Be to Cu. Moreover, it was confirmed that the measured temperatures agreed well with the analysis temperatures, which were used to estimate the lifetime and that the developed facility showed its capability of the long time operation.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.2
• /
• pp.114-135
• /
• 2013

Among the UNESCO World Heritage Sites, the proportion of natural heritage to cultural heritage is relatively small. In 2007, the "Jeju Volcanic Island and Larva Tubes" was the first one that was designated as an UNESCO World Natural Heritage Site in Korea. The growing Korean geological heritage condition and conservation case studies on management of the geological heritage were examined in this study. Furthermore, the purpose of this study is to show future driving strategy for conservation and improvement plan on our geological heritage. Natural Monuments as a state-designated natural property and Geoparks as a new application system for geological heritage are important to conserve our geological heritage. Public engagement through establishment of visitor centers is definitely needed to improve education and promotion. The study includes field investigation for the "Wadden Sea", an World Natural Heritage Site for a mud flat, interviews with staffs and experts who are responsible for investigating and managing the site. Three factors can likely be attributed to its successful management and conservation policy for the "Wadden Sea". First of all, there is an operation for integrated management system and joint secretariat for research and monitoring. Next, researchers invigorate the visitor centers for promotion and education on geological heritage. Finally, experts and staffs implement various research topics and projects based on a long-range plan. The study was carried out to evaluate the present condition of our geological heritage and to make a proposal as a policy to improve value and conserve them. In conclusion, this study provided future discussion that may help researchers to make a decision on long-term policies for the geological subject of Korean natural heritage.