• Journal of the Korean Institute of Intelligent Systems
• /
• v.11 no.8
• /
• pp.709-714
• /
• 2001

Recently, most vehicles has the Automatic transmission system as their transmission system. The automatic transmission system operates with fixed shift patterns. In the opposite of manual operation, it is easy and convenient for driving. Though these merit, the system can not evaluate the driver s intension because of usage of fixed shift pattern. To consider driver s intension, we must consider both the driving intensity of driver and the status of vehicle. In this paper, we developed flexible automatic transmission system by using the proposed moduled neural networks which can learn the status of th vehicle and driver s intensity. As a results, we compare the transmission system using fixed shift pattern and the proposed transmission system and show the good performance in the change of shift position.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.141-151
• /
• 2006

A blank test was done to calculatee the car itself's magnetic effect as noise and to eliminate it from the data set of total magnetic intensity(=magnetic flux density) exploration in a car-borne magnetic exploration system. To calculate the induced magnetic intensity(= magnetization) and the remanent magnetic intensity(= magnetization) of the car itself, we have installed the magnetometer on a fixed point and measured the magnetic intensity letting the car move around the magnetometer, and we have changed the data set into an analogous data set as if acquired in the condition that we have parked the car on the same fixed point and measured the magnetic intensity moving the magnetometer around the magnetometer. Through an inversion with the later data set as input, we have calculated the magnetic center and the magnetic moments of the induced magnetic intensity(= magnetization) and the remanent magnetic intensity(= magnetization) of the car itself with the two centers coincided because of some barriers of the inversion algorithm that we have used in this study. On the other hand, we have extracted the magnetic anomaly by reducing i. e. vectorially eliminating the induced magnetic intensity(= magnetization) and the remanent magnetic intensity(= magnetization) of the car itself calculated forwardly, from the magnetic exploration data set acquired by the car-borne magnetic exploration system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.7 s.94
• /
• pp.1794-1804
• /
• 1993

The thermal stress intensity factors for interface cracks of Griffith and symmetric lip cusp types under vertical uniform heat flow in a finite body are calculated by boundary element method. The boundary conditions on the crack surfaces are insulated or fixed to constant temperature. The relationship between the stress intensity factors and the displacements on the nodal point of a crack tip element is derived. The numerical values of the thermal stress intensity factors for interface Griffith crack in an infinite body and for symmetric lip cusp crack in a finite and homogeneous body are compared with the previous solutions. The thermal stress intensity factors for symmetric lip cusp interface crack in a finite body are calculated with respect to various effective crack lengths, configuration parameters, material property ratios and the thermal boundary conditions on the crack surfaces. Under the same outer boundary conditions, there are no appreciable differences in the distribution of thermal stress intensity factors with respect to each material properties. But the effect of crack surface thermal boundary conditions on the thermal stress intensity factors is considerable.

• Agribusiness and Information Management
• /
• v.6 no.1
• /
• pp.37-44
• /
• 2014

This study was conducted to evaluate light intensity and uniformity of two SMD (surface-mount device) type LEDs for protected crop production. A low-power (0.1 W) and a high-power (1 W) LEDs were selected and the intensity and uniformity was evaluated at different vertical (height) and horizontal (distance) intervals. When the horizontal interval of the LED bar was fixed, the light intensity increased and the uniformity decreased as the height decreased. At the 30~40 cm heights, 20~30% of the area showed $200{\pm}20{\mu}molm^{-2}s^{-1}$. As the horizontal distance of the LED bars increased, while the uniformity increased as well, the light intensity decreased. At the distances of 6~10 cm, 17~23% of the area showed $200{\pm}20{\mu}molm^{-2}s^{-1}$. When the LED bars were added to the sides, the light intensity and uniformity were generally improved. Results showed that the light intensity and uniformity depended on the height and interval of the LED bulbs; therefore, optimum arrangement for the crops interested should be determined through experiments.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.7
• /
• pp.501-508
• /
• 2021

The largest source of revenue in Indonesia comes from the taxation sector. Taxes increase the state revenue, which the government utilizes for building public facilities and infrastructures, providing subsidies to the public, financing public interests, and so on. In addition to producing revenue, taxes may be used to promote economic stability. Thus, this study aims to examine and analyze the financial aspects of tax aggressiveness. The financial aspects include leverage, capital intensity, inventory intensity, and earning management. The population used in this study was manufacturing companies listed on the Indonesia Stock Exchange (IDX) for the 2016-2019 period. Data analysis was carried out based on Eviews, with a selected sample of 32 companies of four observation years. Therefore, the number of samples was 128. The results of this study revealed that the best estimation model to use is the Fixed Effect Model (FEM). This study proved that leverage and earning management had a positive and significant effect on tax aggressiveness. In contrast, capital intensity and inventory intensity did not affect tax aggressiveness. In addition, the result of this study is still far from perfect. It is, therefore, hoped that further research can add other variables to find better results.

• Journal of Bio-Environment Control
• /
• v.29 no.1
• /
• pp.43-51
• /
• 2020

For developing a canopy photosynthesis model, an efficient method to measure the photosynthetic rate in a growth chamber is required. The objective of this study was to develop a method for establishing canopy photosynthetic rate curves of romaine lettuce (Lactuca sativa L.) with light intensity and CO₂ concentration variables using controlled growth chamber. The plants were grown in plant factory modules, and the canopy photosynthesis rates were measured in sealed growth chambers made of acrylic (1.0 × 0.8 × 0.5 m). First, the canopy photosynthetic rates of the plants were measured, and then the time constants were compared between two application methods: 1) changing light intensity (340, 270, 200, and 130 μmol·m^-2·s^-1) at a fixed CO₂ concentration (1,000 μmol·mol^-1) and 2) changing CO₂ concentration (600, 1,000, 1,400, and 1,800 μmol·mol^-1) at a fixed light intensity (200 μmol·m^-2·s^-1). Second, the canopy photosynthetic rates were measured by changing the light intensity at a CO₂ concentration of 1,000 μmol·mol^-1 and compared with those measured by changing the CO₂ concentration at a light intensity of 200 μmol·m^-2·s^-1. The time constant when changing the CO₂ concentration at the fixed light intensity was 3.2 times longer, and the deviation in photosynthetic rate was larger than when changing the light intensity. The canopy photosynthetic rate was obtained stably with a time lag of one min when changing the light intensity, while a time lag of six min or longer was required when changing the CO₂ concentration. Therefore, changing the light intensity at a fixed CO₂ concentration is more appropriate for short-term measurement of canopy photosynthesis using a growth chamber.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.119-129
• /
• 1990

In case that the body with a cusp crack is under uniform heat flow, thermal stress intensity factors are calculated by using boundary element method with linearized body force term. The crack surface is under insulated or fixed temperature condition and the types of crack are symmetric lip and airfoil cusps. Numerical values of thermal stress intensity factors for a Griffith crack and cusp cracks in infinite bodies are proved to be in good agreement within .+-.5% when compared with the previous numerical and exact solutions, respectively. The thermal stress intensity factors for symmetric lip and airfoil cusp cracks in finite bodies are calculated about various effective crack lengths, configuration parameters, and heat flow directions. With the same crack surface thermal boundary conditions, heat flow directions and crack lengths, there are no appreciable differences in variations of thermal stress intensity factors between symmetric lip and airfoil cusp cracks. The signs of thermal stress intensity factors for each cusp crack are changed with each crack surface thermal boundary condition.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1255-1265
• /
• 1992

Under uniform heat flow, the thermal stress intensity factors for the interfacial crack on a rigid cusp-type inclusion are determined by Hilbert problem expressed with complex variable. The thermal stress intensity factors are expressed in terms of the periodic function of heat flow angle. When the tip of the interfacial crack meets that of the cusp crack, the thermal stress intensity factors have singularities. The thermal stress intensity factors at the interfacial crack tip located in the distance from the cusp crack tip vary with the location of the interfacial crack tip. From the results of the analysis, the complex potential functions and the thermal stress intensity factors for the cusp-type inclusion without the interfacial crack are derived under the cusp surface boundary conditions insulated or fixed to zero relative temperature.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.6
• /
• pp.1039-1043
• /
• 1997

Correlation among color intensity, electron donating ability to $\alpha$, $\alpha$-diphenyl-$\beta$-dicrylhydrazy(DPPH) and cultivation conditions by Bacillus subtilis DC-2 were tested with response surface methodology. Both of pigment generation ability and DPPH were more affected by temperature than any other factor. The highest correlation was appeared between color intensity and DPPH as 0.8364 which is significant at 1% level. After fixing cultivation time which is not significant at 10% level to 84hrs as optical cultivation time, response surface methodology was conducted in regarding temperature and color intensity. As a result of overlapped contour map of color intensity and DPPH, when cultivation temperature was in the range of 38.9~41.1$^{\circ}C$ and pH was in the range of 8.34~9.12, optical density of color intensity was predicted higher than 0.374 at 390nm and DPPH was infered higher than 1.310 at 528nm. In the range of optical culture condition, cultivation temperature, pH and cultivation time was fixed to 4$0^{\circ}C$, 8.5 and 85hrs, respectively. In resulting, observation value of color intensity and DPPH was in the range of anticipation value as 0.386 at 390nm and 1.332 at 528nm respectively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.1999-2010
• /
• 1992

The fixed slab analogy device which can measure stress intensity factors(S.I.F) experimentally by slab analogy theory is developed in this paper. The margin of errors resulted from the new testing apparatus are between 0.02% and 8.25%. Therefore, it is assured that this one can be effectively used for the more accurate measurement of S.I.F.( $k_{I}$, $k_{I I}$) than conventional apparatus. The pitch of master grating used in this experiment is 0.1mm It is known that the ratio of the distance from crack tip to the crack length on obtaining the accurate stress intensity factor is between 0.4 and 0.7. The optimum curvature radius of slab is about 125mm. The thickness of slab(plate) used in the fixed slab analogy device is 0.05mm(P.V.C. ; E = 64 MN/ $m^{2}$, .nu.=0.38), which is proved to be suitable for the test. The optimum material for the frame(slab`s external boundary) is a alloy tool steel(SKS 5) plate and its thickness is 1mm. In this research, the rigid cracks are directly bonded to the slab surface by cyanoacrylate adhesive for the easiness of slab making and conformity to the practical crack figure. The material of rigid crack is thin steel plate. It is expected that the developed method can be used effectively for the analysis of $k_{I}$ and $k_{I I}$ of arbitrary shaped or distributed cracks.cks.