• 제목/요약/키워드: firing condition matrix

검색결과 13건 처리시간 0.026초

EMFG의 개선된 동작해석 알고리즘 (The Enhanced Analysis Algorithm for an EMFG's Operation)

  • 김희정;여정모;서경룡
    • 정보처리학회논문지A
    • /
    • 제9A권3호
    • /
    • pp.371-378
    • /
    • 2002
  • EMFG(Extended Mark Flow Graph)는 이산시스템을 표현하는데 유용한 그래프 도구로 알려져 있다. 본 연구에서는 EMFG에서 각 트랜지션이 점화하였을 때의 입출력 박스의 마크 변화량을 입출력 행렬로 표현하였고, 이를 사용하여 EMFG의 접속행렬을 구하였다. 점화가능벡터를 구하기 위하여 각 트랜지션의 점화조건을 점화조건행렬로 표현하였으며, 각 트랜지션의 점화완료 상태를 판단하기 위하여 점화완료벡터를 도입하였다. 이들을 사용하여 EMFG의 모든 동작과정이 수학적으로 해석될 수 있도록 EMFG의 동작해석 알고리즘을 개선하였다. 제안된 알고리즘을 정회전과 역회전을 반복하는 시스템에 적용하여 알고리즘이 올바르게 동작하는 것을 확인하였다. 제안된 알고리즘은 다양한 이산 시스템을 분석하는데 유용하다.

발전용 대형 2행정 디젤 엔진의 비틈진동 해석 (Torsional Vibration Analysis in Large Two-Stroke Diesel Engines for Stationary Power Plants.)

  • 박종포;박희주
    • 대한기계학회논문집A
    • /
    • 제24권10호
    • /
    • pp.2529-2534
    • /
    • 2000
  • Torsional vibration analysis in a large two -stroke low speed diesel engine and generator system for stationary power plants is performed to verify that the vibration characteristics of shafting system meet design requirements. Our own developed S/W is employed for the analysis, whose results are evaluated comparing with measurements. Vibration analysis results of the system are presented according to the change of loading(unload, 100%load, 110% load) and operating(mis-firing, uneven firing) conditions of the stationary power plants.

Comb형 전극구조를 갖는 AC 플라즈마 디스플레이 패널의 방전특성 (Discharge Properties of an AC Plasma Display Panel with Comb-Type Electrodes)

  • 김동수;장지근;임성규;장호정
    • 한국재료학회지
    • /
    • 제9권2호
    • /
    • pp.195-198
    • /
    • 1999
  • The newly designed Ac-PDP(plasma display panel with comb-type electrode) structure was fabricated by using the screen printing method and the electrical and optical characteristics were measured under the various discharge conditions. The minimum firing voltages measured under pure Ne and Ne+Xe mixture gas with the application of 10 kHz square wave were 190V and 160V, respectively. The firing voltages of the PDP cell with the comb-type electrode were compared with those of the cell with matrix electrode under the same discharge condition. The firing voltage of the PDP cell with comb-type electrode was 15 V lower than that of the PDP cell with conventional matrix electrodes.

  • PDF

접속 행렬을 이용한 순차 시스템 제어기 설계 (Design of Sequential System Controller Using Incidence Matrix)

  • 전호익;류창근;우광준
    • 조명전기설비학회논문지
    • /
    • 제12권1호
    • /
    • pp.85-92
    • /
    • 1998
  • 본 논문에서는 페트리 네트로 記述된 제어 사양을 접속 행렬로 해석한 후, 그 결과를 근거로 병렬 시퀸스의 수행이 가능한 순차 시스템 제어기(Sequential System Controller)를 설계하였다. 순차 시스템 제어기는 입력 처리부, 그리고 점화 처리부와 토큰 제어기로 구성된 페트리 네트 제어기로 구성된다. 입력 처리부에서는 입력 신호를 선택하여 점화 처리부로 전달하며, 점화 처리부는 토큰 운전기의 토큰 상태에 따라서 입력된 신호의 점화 여부를 판단하게 된다. 제안된 제어기는 제어 사양의 변경시 접속 행렬을 저장한 롬의 내용 변경만으로 제어기의 변경이 가능하고, 페트리 네트 제어기의 모듈화가 가능하여 기능의 확장이 용이하므로 자동창고 시스템, 반송 시스템, 및 승강기 시스템과 같은 순차 시스템 제어기의 개발 및 실현을 용이하게 할 수 있다.

  • PDF

추이적 행렬을 이용한 패트리 넷 모델의 분석방법에 대한 연구 (A study on the analysis method of Petri Net Models Using the Transitive Matrix)

  • 송유진;이종근
    • 한국시뮬레이션학회논문지
    • /
    • 제10권1호
    • /
    • pp.13-24
    • /
    • 2001
  • We propose a divide-conquer method of Petri nets under the condition of one-boundedness for all the Petri nets. We introduce the P-invariant transitive matrix of Petri nets and relationship between them. The feature of the P-invariant transitive matrix is that each element stands for the transitive relationship between input place and output place through the firing of the enable transition.

  • PDF

알루미나를 충전재로 첨가한 붕규산염 유리의 소결 및 결정화 방지기구에 대한 연구 (A Study on the Sintering and Mechanism of Crystallization Prevention of Alumina Filled Borosilicate Glass)

  • 박정현;이상진;성재석
    • 한국세라믹학회지
    • /
    • 제29권12호
    • /
    • pp.956-962
    • /
    • 1992
  • The predominant sintering mechanisms of low firing temperature ceramic substrate which consists of borosilicate glass containing alumina as a filler are the rearrangement of alumina particles and the viscous flow of glass powders. In this system, sintering condition depends on the volume ratio of alumina to glass and on the particle size. When the substrate contains about 35 vol% alumina filler and the average alumina particle size is 4 $\mu\textrm{m}$, the best firing condition is obtained at the temperature range of 900∼1000$^{\circ}C$. The extensive rearrangement behavior occurs at these conditions, and the optimum sintering condition is attained by smaller size of glass particles, too. The formation of cristobalite during sintering causes the difference of thermal expansion coefficient between the substrate and Si chip. This phenomenon degradates the capacity of Si chip. Therefore, the crystallization should be prevented. In the alumina filled borosilicate glass system, the crystallization does not occur. This effect may have some relation with aluminum ions in alumina. For aluminum ions diffuse into glass matrix during sintering, functiong as network former.

  • PDF

경상북도 청도군 성곡리에서 출토된 4-6세기 토기의 광물학적 특성 연구 및 소성환경 추정 (Study on Mineralogical Characteristics and Firing Condition of the 4-6th Century Earthenware Excavated from the Seonggok-ri, Cheongdo-gun, Gyeongsangbuk-do)

  • 우현동;김옥순;장윤득
    • 한국광물학회지
    • /
    • 제29권3호
    • /
    • pp.123-129
    • /
    • 2016
  • 본 연구에서는 경상북도 청도군 성곡리 고분군 일대에서 발견된 4-6세기 토기를 대상으로 암석 광물학적인 특성과 소성온도 및 환경을 추정하고 그 결과를 인접지역인 창녕 토기와 대조하였다. 편광현미경 하에서 석영과 유리질 기질부가 주를 이루었으며 장석, 화산암편, 불투명광물 등이 관찰되었다. 또한, 석영은 대부분 융식된 형태로 나타났고 기공의 일부는 비정질석영으로 채워져 있었다. XRD 분석결과 멀라이트, 적철석, 크리스토발라이트 함량이 추가로 인지되었고, SEM을 통해 관찰한 토기의 내부조직에서 고온을 지시하는 멀라이트가 토기 내 전체적으로 고른 분포를 보였다. 이러한 결과들을 바탕으로 청도 토기는 멀라이트의 결정화가 활발해지면서 스피넬이 없어지는 약 1,100 내지 $1,200^{\circ}C$에서 소성되었음을 추론할 수 있는데, 이는 인접한 지역인 창녕 토기의 약 $1,000^{\circ}C$ 에 비해 높은 수치다. 또한, 멀라이트의 분포특성에서 드러난 두 지역 토기의 차이는 청도 토기가 창녕 토기에 비해 소성시간이 더 길었거나, 가마 내에서 더 균질한 열적 환경이 조성되었을 가능성을 시사한다.

단일액체추진제 하이드라진 추력기의 펄스모드 추력 거동 연구 (A Study on the Pulse-mode Thrust Behavior of Liquid-monopropellant Hydrazine Thruster)

  • 김정수;박정;최종욱;김성초;장기원
    • 한국추진공학회:학술대회논문집
    • /
    • 한국추진공학회 2005년도 제24회 춘계학술대회논문집
    • /
    • pp.194-197
    • /
    • 2005
  • 추진제 주입압력 350 psia 에서 0.95 lbf 의 정상상태 공칭추력을 내는 단일액체추진제 하이드라진 추력기의 펄스모드 성능평가 결과를 제시한다. 연소시험 절차에 대한 간략한 기술과 함께 펄스모드 작동으로부터 얻어지는 추진제 공급압력, 추력기 작동환경 진공도, 그리고 추력 등의 변이거동에 대한 전형적인 결과를 추력기의 열적 반응과 더불어 검토한다. 제시된 성능은 1-lbf급 표준형 단일추진제 로켓엔진의 펄스모드 기준성능과 성공적으로 비교된다.

  • PDF

이산시간 퍼지 다개체 시스템의 상태일치 기반 대형 추종 제어기 (Consensus-Based Formation Tracking of Fuzzy Multi-Agent Systems)

  • 문지현;지성철;이호재
    • 전기학회논문지
    • /
    • 제63권8호
    • /
    • pp.1080-1084
    • /
    • 2014
  • This paper addresses a design technique for formation tracking controllers of discrete-time Takagi-Sugeno fuzzy multi-agent systems based on consensus. The interconnection topology among the agents is expressed as a digraph. The design condition is represented in terms of linear matrix inequalities. Numerical example demonstrates the effectiveness of the proposed method.

포렌식 마킹을 위한 특징점 기반의 동적 멀티미디어 핑거프린팅 코드 설계 (A Design on the Multimedia Fingerprinting code based on Feature Point for Forensic Marking)

  • 이강현
    • 전자공학회논문지CI
    • /
    • 제48권4호
    • /
    • pp.27-34
    • /
    • 2011
  • 본 논문에서는 멀티미디어 콘텐츠 보호에 대한 반공모 코드를 위한 동적 멀티미디어 핑거프린팅 코드를 설계하는 알고리즘을 제안한다. 기존의 반공모 코드(ACC: Anti-Collusion Code)를 위한 멀티미디어 핑거프린팅 코드는 BIBD(Balanced Incomplete Block Design)의 접속행렬을 보수행렬로 변환하여 k를 k+1로 증대시키는 수리적 방법으로 설계되었다. 그리고 보수행렬의 코드벡터를 사용자에게 핑거프린팅 코드로 부여하고, 콘텐츠에 삽입하였다. 제안된 알고리즘에서는 사용자가 구매하는 콘텐츠로부터 특징점을 추출하고, 이를 기반으로 동적으로 핑거프린팅 코드를 설계할 수 있도록 BIBD의 v와 k+1 조건을 만족하는 반공모 코드의 후보성 코드를 코드북(Codebook)에 구축하고 ${\lambda}+1$ 조건을 만족하는 행렬(이하, Rhee행렬이라 함.)을 생성한다. 실험을 통하여 콘텐츠의 특징점 기반으로 생성된 Rhee행렬의 코드벡터는 v비트의 유의수준 ($1-{\alpha}$)에서 신뢰구간에 k가 존재하며, Rhee행렬의 각 행과 행, 열과 열 사이의 유클리디안 거리가 BIBD 기반의 보수행렬과 그래프 기반의 보수행렬과 같은 k값이 산출되었다. 더욱이 Rhee행렬의 첫 행과 첫 열은 생성과정에서 초기 점화벡터로 콘텐츠 포렌식 마크 정보가 되며, 이와 관계가 있는 나머지 코드벡터들과의 관계성이 코드북에 기록되어 있기 때문에, 공모된 코드를 추적할 때 원 핑거프린팅 코드의 상관관계 계수를 구할 필요 없이 코드북의 탐색으로 공모자를 추적이 용이하다. 따라서 본 논문에서 생성된 Rhee행렬은 수리적으로 생성된 BIBD 기반의 행렬보다 ACC로서 강인성과 충실도가 우수하다.