• Atmosphere
• /
• v.23 no.4
• /
• pp.485-500
• /
• 2013

This study conducted WRF-Fire simulations in order to investigate sensitivities of the resolution of fire fuel and terrain data sets, and the surface wind to simulated fire area. The sensitivity simulations were consisted of 8 different WRF-Fire runs, each of which used different combination of data sets of fire fuel and terrain with different resolution. From the results it was turned out that the surface wind was most sensitive. The next was fire fuel and then fire terrain. Unfortunately, every run produced too much fire area. In other words no simulations succeeded in simulating such proper fire area so as for the WRF-Fire to be used realistically. It was verified that the errors of fire area from each runs were contributed by 41%, 53%, and 6% from surface wind, fire fuel, and fire terrain, respectively. Finally this study suggested that the selection of Anderson fuel category in the area of interest seemed to be very critical in the performance of WRF-Fire simulations.

• Journal of Forest and Environmental Science
• /
• v.36 no.4
• /
• pp.298-310
• /
• 2020

Fuel management can play enormous role in fire management in tropical dry forests. However, unlike the temperate forests, knowledge on implications of different fuel management methods in tropical forests is often inadequate. In this study, the implications of prescribed burning and hand thinning treatments on implementation cost, fuel loading and post-treatment fire behaviour were tested and compared in degraded forests and teak plantations in two forest reserves of different levels of dryness in Ghana. The study found that prescribed burning was less expensive (62.02 US Dollars ha-1) than hand thinning (95.37 US Dollars ha-1). The study also indicated that the two fuel management methods were able to reduce fuel loading in degraded forests and teak plantations. However, prescribed burning was more effective in reducing fuel loading than hand thinning. While the relative change of fuel reduction was 13% higher in prescribed burning than the hand thinning in degraded forest, it was 41% higher in prescribed burning than hand thinning in teak plantations. The fire behaviour of post-treatment experimental fire was also lower in prescribed burning than the hand thinning and control plots. Fuel management, therefore, has a great potential in fire management in degraded forests and teak plantations in Ghana.

• Nuclear Engineering and Technology
• /
• v.55 no.7
• /
• pp.2604-2612
• /
• 2023

Spent nuclear fuel and long-lived radioactive waste must be carefully handled before disposing them off to a geological repository. After the pre-storage period in water pools, spent nuclear fuel is stored in casks, which are widely used for interim storage. Interim storage in casks is very important part in the whole cycle of nuclear energy generation. This paper presents the results of the numerical study that was performed to evaluate the thermal behavior of a metal-concrete CONSTOR RBMK-1500 cask loaded with spent nuclear fuel and placed in an open type interim storage facility which is under fire conditions (steady-state, fire, post-fire). The modelling was performed using the ANSYS Fluent code. Also, a local sensitivity analysis of thermal parameters on temperature variation was performed. The analysis demonstrated that the maximum increase in the fuel load temperatures is about 10 ℃ and 8 ℃ for 30 min 800 ℃ and 60 min 600 ℃ fires respectively. Therefore, during the fire and the post-fire periods, the fuel load temperatures did not exceed the 300 ℃ limiting temperature set for an RBMK SNF cladding for long-term storage. This ensures that fire accident does not cause overheating of fuel rods in a cask.

• Fire Science and Engineering
• /
• v.26 no.1
• /
• pp.49-60
• /
• 2012

The change in fuel moisture in accordance with the number of days after rainfall is an important factor in predicting forest fire dangers and supporting forest fire rangers. Therefore, in order to clear up these forest fire occurrence conditions, forest fire danger levels for surface fuel 0.6 cm or lower, 0.6~3.0 cm, 3.0~6.0 cm, and 6.0 cm or above by fallen leaves layer, humus layer, soil layer, and diameter after rainfall of 5.0 mm and higher in accordance with tree density in 2008, 2009 Spring/Autumn Young Dong region have been analyzed. Research showed an approximate 17 % fuel moisture which is a dangerous forest fire occurrence level after 5 days from rainfall in medium-density areas and 3 days after rainfall in loose-density areas of Spring time in the fallen leaves layer. On the other hand, the humus layer showed a 40 % or higher fuel humidity even after 6 days from rainfall regardless of the season, while the upper and lower parts of the soil layer had a little change. In loose-density areas with 0.6 cm or less surface fuel per diameter in Spring time, the fuel humidity displayed a dangerous level in fire forest occurrence after 3 days, and 4days in medium-density areas, and for loose-density areas with 0.6~3.0 cm surface fuel per diameter in Autumn time it showed a dangerous level in forest fire occurrence after 3 days, and for medium-density areas, 5 days. In the case of 3.0~6.0 cm of fuel moisture per diameter in both Spring and Autumn times, even after 6 days, low and medium-density areas showed that they maintain fuel moisture and therefore the dangers of forest fires were very low, and in the case of 6.0 cm or higher, it showed 25 % or higher fuel moisture even after 6 days from rainfall regardless of the season.

• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.481-487
• /
• 2005

In this study, a GIS model to simulate the behavior of surface forest fires was developed on the basis of forest fire growth prediction algorithm. This model consists of three modules for data-handling, simulation and report writing. The data-handling module was designed to interpret such forest fire environment factors as terrain, fuel and weather and provide sets of data required in analyzing fire behavior. The simulation module simulates the fire and determines spread velocity, fire intensity and burnt area over time associated with terrain slope, wind, effective humidity and such fuel condition factors as fuel depth, fuel loading and moisture content for fire extinction. The module is equipped with the functions to infer the fuel condition factors from the information extracted from digital vegetation map sand the fuel moisture from the weather conditions including effective humidity, maximum temperature, precipitation and hourly irradiation. The report writer has the function to provide results of a series of analyses for fire prediction. A performance test of the model with the 2002 Chungyang forest fire showed the predictive accuracy of 61% in spread rate.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.518-525
• /
• 1997

A series of measurements and visualization to investigate the interaction of water sprays with pool fires is presented. Fire source is a small-scale pool burner with methanol, ethanol and gasoline. Measurements of temperatures, $O_2$, $CO_2$, and CO concentrations along the plume centerline are carried out to observe pool fire structures without water sprays. Visualization by the Ar-ion laser sheet shows flow pattern of droplets of the sprays above the pool fires. It is observed that in the case of methanol and ethanol, water sprays continuously penetrate into the center of fuel surfaces. The gasoline pool fire allows intermittent penetration of water sprays because of pulsating characteristics of the gasoline flame. To evaluate the cooling effect of the fuel surface by the sprays, the temperature was measured at the fuel surface. As soon as the mists reach the fuel surface of methanol and ethanol, the temperatures of the fuel surface decrease rapidly below the boiling point, and then the fires are extinguished. Due to the application of mist upon the gasoline fire, though the fuel temperature decrease abruptly at the time of the injection, such a rapid decrease do not continue till the extinction point.

• Journal of the Korean Society of Safety
• /
• v.29 no.6
• /
• pp.62-67
• /
• 2014

This study was performed to analyze the vulnerability of the situation in which combat system is shot by external projectile impacts. In developing combat system, it is vital to consider the survivability as well as its mission capability because it is directly connected with loss of lives. Especially, when the parts which are susceptible to fire are shot under battle situation, the system is exposed to the dangerousness and the situation when the parts such as fuel tanks are impacted by external projectile impacts can lead to flash fire as a result of the leakage of fuel. Therefore, in this study the possibility of flash fire was calculated by analyzing a variety of variables supposing that fuel tank in the combat system is shot. The aim of this study is to suggest effective methods in the basic steps when combat system is designed.

• Fire Science and Engineering
• /
• v.11 no.4
• /
• pp.15-23
• /
• 1997

A series of measurements and visualization to investigate the extingushiment of water sprays with pool fires is presented. Fire source is a small-scale pool burner with methanol, ethanol and gasoline. Measurements of temperature, O2, CO2, and CO concentrations along the plume centerline are carried out to observe pool structures without water sprays. Visualization by the Ar-ion laser sheet flow pattern of droplets of the sprays above the pool fires. It is observed than in the case of methanol and ethanol, water sprays continuously penetrate into the center of fuel surfaces. The gasoline pool fire allows intermittent penetration of water sprays because of pulsating characteristics of the gasoline flame. To evaluate the cooling effect of the fuel surface by the sprays, the temperature was measured at the fuel surface. As soon as the mists reach the fuel surface of methanol and ethanol, the temperatures of the fuel surface decrease rapidly below the boiling point, and then the fires are extinguished. Due to the application of mist upon the gasoline fire, though the fuel temperature decrease abruptly at the time of the injection, such a repid decrease do not continue till the extinction point.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.5 no.3
• /
• pp.179-184
• /
• 2003

This study investigated the relationship of fuel weight and depth together with slope on the spread of forest fire. Fire spread was faster on the greater slope in forested land. Fire had a greater spread rate with lighter fuel weight. The thickness of the fuel bed and forest fire spread rate were not related. The fire spread rate was closely related to the slope and weight of the fuel bed (significant at 0.01, 0.05, respectively). The thickness of the fuel bed was not significant (0.05).

• Fire Science and Engineering
• /
• v.33 no.2
• /
• pp.47-55
• /
• 2019

The prediction performance of design fire curves was evaluated using a Fire dynamics simulator (FDS) for a solid fuel fire in a building space by comparing the results with experimental data. EDC 2-step mixing controlled combustion model was used in the FDS simulations and the previously suggested 2-stage design fire (TDF), Quadratic and Exponential design fire curves were used as the FDS inputs. The simulation results showed that smoke propagation in the building space was significantly affected by the design fire curves. The predictions of simulations using design fire curves for the experimental temperatures in the building space were reasonable, but the TDF was found to be the most acceptable for predicting temperature. The predictions with each design fire curve of species concentrations showed insufficient agreement with the experiments. This suggests that the combustion model used in this study was not optimized for the simulation of a solid fuel fire, and additional studies will be needed to examine the combustion model on the FDS prediction of solid fires.