• Smart Structures and Systems
• /
• v.12 no.6
• /
• pp.695-705
• /
• 2013

The purpose of this paper is to identify through experiments the finite element (FE) model of a building structure using a magnetorheological (MR) fluid damper. The FE model based system identification (FEBSI) technique evaluates the control performance of an MR damper that has nonlinear characteristics as equivalent linear properties such as mass, stiffness, and damping. The Bingham and Bouc-Wen models were used for modeling the MR damper and the equivalent damping increased by the MR damper was predicted by applying an equivalent linearization technique. Experimental results indicate that the predicted equivalent damping matches well with the experimentally obtained damping.

• Smart Structures and Systems
• /
• v.4 no.1
• /
• pp.35-46
• /
• 2008

In this paper the authors address the problem of comparing two different smart damping techniques using the numerical modelling of the electro-mechanical impedance for plate structures partially treated with active constrained layer damping treatments. The paper summarizes the modelling procedures including a finite element formulation capable of accounting for the observed behaviour. The example used is a smart cantilever plate structure containing a viscoelastic material (VEM) layer sandwiched between a piezoelectric constrained layer and the host vibrating plate. Comparisons are made between active constrained layer and active damping only and based on the resonance frequency amplitudes of the electrical admittance numerically evaluated at the surface of the piezoelectric model of the vibrating structure.

• Structural Engineering and Mechanics
• /
• v.66 no.4
• /
• pp.439-444
• /
• 2018

This paper presents a numerical study on the behavior of continuous hollow steel beam strengthened using carbon fiber reinforced polymers (CFRP). Most previous studies on the CFRP strengthening of steel beams have been carried out on the steel beams with simple boundary conditions. No independent study, to the researcher's knowledge, has studied on the CFRP strengthening of square hollow section (SHS) continuous steel beam. However, this study explored the effect of the use of adhesively bonded CFRP flexible sheets on the behavior of the continuous SHS steel beams. Finite Element Method (FEM) has been employed for modeling. Eleven specimens, ten of which were strengthened using CFRP sheets, were analyzed under different coverage length, the number of layers, and the location of CFRP composite. ANSYS software was used to analyze the SHS steel beams. The results showed that the coverage length, the number of layers, and the location of CFRP composite are effective in increasing the ultimate load capacity of the continuous SHS steel beams. Application of CFRP composite also caused the ductility increase some strengthened specimens.

• Steel and Composite Structures
• /
• v.24 no.3
• /
• pp.339-349
• /
• 2017

In this paper, a conventional refined plastic hinge analysis is improved to account for the effects of local buckling and lateral-torsional buckling. The degradation of flexural strength caused by these effects is implicitly considered using practical LRFD equation. The second-order effect is captured using stability functions to minimize modeling and solution time. An incremental-iterative scheme based on the generalized displacement control method is employed to solve the nonlinear equilibrium equations. A computer program is developed to predict the second-order inelastic behavior of space steel frames. To verify the accuracy and efficiency of the proposed program, the obtained results are compared with the existing results and those generated using the commercial finite element package ABAQUS. It can be concluded that the proposed program proves to be a reliable and effective tool for daily use in engineering design.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.543-546
• /
• 2001

So far, the design methods of quartz crystal resonator have been developed. Recently, as the electronic package and semiconductor modules become smaller, the need to minimize the sizes of crystal components grows larger. but Minimizing crystal plate sizes has limitations because its temperature-frequency characteristics is worse and unwanted resonances occur. so appropriate design of electrode size and crystal plates is necessary. In this palter, Two-dimensional governing equations for electroded piezoelectric crystal plates with general symmetry have been solved from deduced equations from three-dimensional equations of linear piezoelectricity in most cases. In practice, electroded piezoelectric crystal plates have three-dimensional geometry, so simplified 2-dimensional equations and 2-D modeling are insufficient for explaining its resonance modes and characteristics. So, three-dimensional FEM(finite element method) analysis is done and its effectiveness is verified from analyzing practical crystal resonator model.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.930-932
• /
• 2001

This paper is proposed the modeling and computational methods for estimating the steady and dynamic characteristics of a transverse flux type SRM. Prediction of the steady and dynamic characteristics state of a switched reluctance motor (SRM) drive can be quite involved because of complex interdependent influences between motor parameters and excitation. To obtain characteristics parameters of the transverse flux type SRM which is considered the magnetic non-linearity phenomena, the magnetic equivalent parameters of SRM are computed by the finite element method as functions of the input current and angular displacement. Dynamic characteristics of the designed transverse flux type SRM is simulated and estimated by Matlab/simlunk.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.872-877
• /
• 2004

Welding residual stresses are the main topics of welding research fields. The residual stresses and distortion of structures by welding exert negative effect on the safety of mechanical structures. That is, expansion of material by high temperature and distortion by cooling during welding process are caused by tensile and compressive residual stresses in welding material, and this residual stresses can induce fracture and fatigue problems of welding structures. The accurate prediction of residual stress and relaxation due to mechanical loading of weld zone is very important to improve the quality of weldment. In this study, a finite element modeling technique is developed to simulate the relaxation of residual stresses due to mechanical loading. The effects of load ratio for static and cyclic loading are evaluated based on analytical results.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2001.10a
• /
• pp.274-279
• /
• 2001

This paper presented a virtual manufacturing simulation system by using Virtual Reality Modeling Language (VRML) and Finite Element Method(FEM). The system is to simulate forging operation. Stress distributions and deformation profiles as well as the operation of forging machine can be simulated and visualized in the web. Since the forging machine, user interface, and specimen were modeled by using Java and VRML, the forging machine and analysis results were browsed and integrated on the web that is interfaced to users through EAI to show the whole forging simulation. The developed system realized the working environment virtually so that education and experiment of forging process could be performed effectively even on the PC.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.97-100
• /
• 2000

Today deep drawing and ironing are the major process in manufacturing of battery case used in cellular phone from aluminum. The same technology is utilized in manufacturing of steel or aluminum cans for components of medical instrument, portable PC, walkman and so on. Most of these processes require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of theses processes are relatively less known. Thus, it is expected that process simulations using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations for High Precision Rectangular Battery Case. A commercially avaliable finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.

• Transactions of Materials Processing
• /
• v.10 no.6
• /
• pp.456-464
• /
• 2001

Deep drawing and ironing are tile major process today in manufacturing of aluminum alloy battery case used in cellular phone. Most of these process require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of these processes are relatively less known. Thus, it is expected that process analysis using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations. To verify the simulation results, the experimental investigations were also carried out on a real industrial product. The numerical analysis by FEM shows good agreement with the experimental results in view of the deformation shape of the product. A commercially available finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.