• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.325-330
• /
• 2001

Shizhuyuan W-Mo-Bi-Ca $F_2$polymetallic ore is classified to the refractory one due to its complex property, fine dissemination and close association of minerals. Through several years of researches, in line with GY new mineral processing technology developed by Guangzhou Research Institute of Nonferrous Metals, in sulfide flotation circuit, an iso-flotability flowsheet is used to replace original overall bulk flotation flowsheet, and in tungsten flotation circuit, a new chelating type-GY reagent and a special pulp-conditioning system and a new technology of wolframite slime flotation are used to replace the traditional "Caustic Soda Method"$_{［1］}$, the metallurgical performance is greatly improved. Besides, GY New Method has created a favorable condition for comprehensive recovery of fluoride from tungsten flotation tailings. Notable economic benefit has been achieved.d.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.511-516
• /
• 2007

Rubber wheeled AGT(Automated Guide-way Transit) system is a prominence transportation system for urban area, because of its low construction cost and management, low noise and vibration and fine exterior view. AGT system uses concrete tracks. Concrete can be easily damaged by the impact, change of temperature and external loads. The fault of concrete track is harmful not only to riding quality but also to bridge. Therefore, in this study, the effects of railway prominence to the bridge are surveyed by experimental method. The experiment was executed for PSC bridge at AGT test line in Kyungsan. And the test results for 5mm, 10mm prominence and without prominence are compared and investigated, according to the vehicle speed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.240-248
• /
• 2004

Recently, the customer's demands for automotive steel sheet have been diversified and sterned more. Therefore, as the tendency of auto industry light-weight, one among these requirements is the trend for high strength together with the thinness of automotive steel sheet. Because Mn added essentially in producing high strength steel sheet is bonded strongly with oxygen, the Fine oxidation layer was created at the welding face after the flash butt welding operated in entry section of pickling line. Thereby it was caused the crack or breakage of welding part in process of cold rolling. At this research, in order to protect the contact Mn with oxygen in atomosphere it was considered to fire oxygen with LNG and the related researches have been gone forward with the find out concrete and to apply them to operation.

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.256-258
• /
• 2003

Hot-rolled and Extruded plates of AZ type magnesium alloys were successfully joined by friction stir welding(FSW). AZ31B-H24 and AZ61 plates with the thickness of 4mm were used, and the microstructural development in the stir zone were investigated using optical and scanning electron microscopes. The grain size of base metal and stir zone were investigated using the line-intersecter method. Hardness of the stir zone was remarkably increased due to very fine recrystallized grain structure both in AZ3l and AZ6l alloys. Tensile strengths of the FS welded Mg alloys AZ31 and AZ61 were strongly affected by formation of the intermetallic compounds, ${\beta}$-Al$\sub$12/Mg$\sub$17/.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.3 s.18
• /
• pp.30-37
• /
• 2004

For a proper operation of portable air defense IR terminal homing missile to the rapid intruding target, the boresight of an IR seeker of the missile should be accurately aligned with the gunner's aiming sight. Before a gunner fires the missile, he tries to keep the target within the circle of ASU ensuring the seeker to lock on the target correctly. In this paper, using an electrical seeker caging loop and IR detector signal characteristics, a precise aligning method between the seeker boresight and the LOS(Line of Sight) of ASU(Aiming Sight Unit) was studied. Although every seeker has slightly different SLA (Signal of Look Angle) output, we can get negligible alignment error through a fine tuning method of electrical caging signal. This alignment procedure was also adopted in K-PSAM system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.79-79
• /
• 2010

The electronic and adsorption structure of O-Phthaladehyde (OPA) on the H-Si(100) surface was investigated by using Near Edge X-ray Fine Structure (NEXAFS) and high resolution photoemission spectroscopy (HRPES). We confirmed that the OPA grown on the H-Si(100) surface showed good dependency with about 60 degree tilting angle using NEXAFS and a single O 1s peak by using HRPES. Hydrogen atom passivated on the Si(100) surface was found to be a seed for making one dimensional organic line that uses a chain reaction as the H-Si(100) surface was compared with the hydrogen free Si(100) surface. Through the spectral analysis, we will demonstrate 1-D directional formation of OPA on H-Si(100) surface using NEXAFS and HRPES.

• Archives of design research
• /
• v.14
• /
• pp.53-60
• /
• 1996

The most remarkable and characteristic problem of design is that of creativity of design. Originality is a part of creativity. In the process of designing, we used to handle design thoughts that shows some patte군 of divergent and productive thoughts. During design thinking, for example 'Idea sketch', We also are under Pattern Recognition and Gestalt principles organization. In this study, it is reorganized that the 'Originality Test of Line Drawing(OTLD)'is a measurement system for personal originality. There is a regression on two tests of OTLD, which has 1 Semester Interval. From the regression data, Test2 = 7.763 + 0.643Test1, F value : 55.219, Prob : 0.0001. We would suggest a measurement system for an ability of originality in design fields, but we couldn't find any reliability and validity for Fine Art fields. In this point, OTLD could be a development tool for design creativity.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.277-278
• /
• 1998

CT/MRI images were frequently taken to evaluate the anatomic structure and disease status, and to plan the treatment modality for oral and maxillofacial surgery. However, surgeons have many difficulties in reading and understanding 2D images without long time experiences. This study presents the method of 3D reconstruction with fine CT slices and its clinical application. We applied this method a clinical patient with oral and maxillofacial trauma and produced 3D reconstructed model which shows the fracture line in panfacial area and bone defect.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.178-183
• /
• 2001

Abrasive jet machining(AJM) process is similar to the sand blasting and effectively removes hard and brittle materials. AJM has applied to rough working such as debarring and rough finishing. As the need for machining of ceramics, semiconductor, electronic devices and LCD are increasing, micro AJM is developed, and has become the inevitable technique to micromachining. This paper describes the performance of the micro AJM in micro grooving of glass. Diameter of hole and width of line in grooving is 80${\mu}{\textrm}{m}$. Experimental results showed good performance in micro grooving of glass, but the size of machined groove increased about 2~4${\mu}{\textrm}{m}$. With the fine tuning of masking process and compensation of film wear. this micro AJM could be effectively applied to the micro machining of semiconductor, electronic devices and LCD.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.589-590
• /
• 2006

Recently, research for the micro printing technology has begun to get into the spotlight. It is due to the superior price competitiveness to existent semi-conductor process for manufacturing some parts of display unit, electronic paper, RF-ID information device, and so on. This paper present screen printing process not for paper publication but for parts of electronics such as PDP wall, LCD CF, and so on. There are two major issues. The first one is how to get a fine and even line pattern. The other one is how to get the same patterns in large area. In this research, we present the design, equipment, and process control of screen printing in order to overcome these issues.