• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.147-150
• /
• 2001

The ARB (Accumulative Rolling Bonding) Process was applied to a 6061 Al alloy to obtain ultra-fine grains. After 4 ARB cycles at $315^{\circ}C$, original equilibrium large grains were transformed to ultra-fine grains of several hundred nano-meter size with nonequilibrium grain boundaries. At lower number of cycles, microsutcture of highly-tangled dislocation cells were observed. Large grains and coarsened precipitates filled the microstructure of specimens experienced ARB cycles more than 5. Sliding wear tests using a pin-on-disk type wear tester were conducted on the ARB processed 6061 Al alloy plate. Wear rates of the 6061 Al alloy increased with the increase of ARB cycle number as well as the applied load. Worn surfaces and debris, cross-sections of the worn specimen were examined with scanning electron microscopy (SEM) to investigate the wear mechanism of the ultra-fine grained 6061 Al Tensile properties of the 6061 Al alloy were also studied and used to correlate the wear test results with the microstructures, which evolved continuously with the number of ARB cycles.

• 한국분말재료학회지
• /
• 제17권3호
• /
• pp.235-241
• /
• 2010

Mo nanopowder was synthesized by ball-milling and subsequent hydrogen-reduction of $MoO_3$ powder. To fabricate ultra fine grained molybdenum, two-step sintering and spark plasma sintering process were employed. The grain size of specimen by two-step sintering and spark plasma sintering was around $0.6\;{\mu}m$ and $0.4\;{\mu}m$, respectively. Mechanical properties of ultra fine grained Mo with relative density of above 90% were significantly improved at room and high temperatures comparing to commercial bulk Mo of 99% relative density. This result was mainly explained by the grain size refinement due to diffusion-controlled sintering.

• 한국지형학회지
• /
• 제26권1호
• /
• pp.27-40
• /
• 2019

This study tries to reveal source areas of fluvial terrace deposits in Danyang and Geum River basins located in the northern and southern parts of the Sobaek Mountains, respectively, through geochemistry. The samples analyzed in this study show different grain size properties and can be grouped into the coarse, medium and fine samples. Grain size properties suggest that the coarse samples are typically fluvial deposits and geochemistry from the coarse samples is also similar to that from the bedrocks within the basins. The fine samples show geochemical properties different from the bedrocks and similar to loess deposits in Korea. However, different geochemical concentrations among the fine samples can be also recognized, indicating mixtures of loess materials with weathering products of the bedrocks. One sample among the medium samples is considered as fluvial deposit due to geochemical similarity to the bedrocks, while geochemistry from another sample among the medium samples indicates that loess materials were mixed with more abundant weathering products of the bedrocks than those in the fine samples.

• 한국결정성장학회지
• /
• 제10권2호
• /
• pp.152-158
• /
• 2000

상압 소결법(PLS, pressureless sintering) 및 방전가열 소결법(SPS, spark plasma sintering)으로 소결한 {{{{ {ZrB }_{2 } - ZrC }}}} 복합체의 미세구조를 SEM-EBSP 법에 의해 결정기하학적으로 분석하였다. PLS법에 의해 소결된 복합체에서 {{{{ { ZrB}_{2 } }}}}의 (1010) 면은ND(시편에 수직인 방향)로 배향되었고, ZrC 경우 (101) 및 (111)면이 ND방향으로 배향되었다. 한편 SPS법에 위해 소결된 {{{{ { ZrB}_{2 } }}}}의 (0001)A면은 ND방향으로 강하게 배향되었다. ZrC인 경우 (001) 면만이 ND방향으로 배향되었다. PLS법에 의한 소결체의 결정립은 특정방위에 대해 약한 배향을 갖으면서, {{{{ { ZrB}_{2 } }}}}와 ZrC상 계면의 구조적 조화가 우수한 반면, SPS법에 의한 소결체의 결정립들은 특정방향으로 강하게 배향되는 경향을 보인다.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.523-532
• /
• 2009

In this study, four API X80 linepipe steel specimens were fabricated with varying cooling rates and finish cooling temperatures, and their microstructures and crystallographic orientations were analyzed to investigate the effects of cooling conditions on their tensile and Charpy impact properties. All the specimens consisted of acicular ferrite, granular bainite, and secondary phases such as martensite and martensiteaustenite constituent. The volume fraction of secondary phases increased with increasing cooling rate, and the higher finish cooling temperature resulted in the reduction in volume fraction and grain size of secondary phases. According to the crystallographic orientation analysis data, the effective grain size and unit crack path decreased as fine acicular ferrites having a large amount of high-angle grain boundaries were homogeneously formed, thereby leading to the improvement of Charpy impact properties. The specimen fabricated with the higher cooling rate and lower finish cooling temperature had the highest upper shelf energy and the lowest energy transition temperature because it contained a large amount of fine secondary phases homogeneously distributed inside fine acicular ferrites, while its tensile properties well maintained.

• 한국지반공학회논문집
• /
• 제27권6호
• /
• pp.49-61
• /
• 2011

본 연구는 토석류의 유통성과 관련하여 세립토의 흐름특성, 유변학적 모델들의 적용가능성 및 액성상태 의존성 유변학적 특성들을 비교 분석하였다. 입자크기에 따른 유변학적 특성을 살펴보고자 점토질이 풍부한 지중해 해저점토와 실트질이 풍부한 캐나다 동부 뉴펀들랜드 와부시 호수에서 채취한 광미에 대한 물성특성을 분석하였다. 점토질이 풍부한 세립토의 경우 전형적인 전단담화(shear thinning) 거동을 보이는 반면, 실트질 광미의 경우는 전단담화와 Bingham 유체 거동을 함께 보인다. 후자의 경우, 전단변형률속도를 높임에 따라 Bingham 유체처럼 거동하였다. 이러한 현상학적 차이는 입자크기에 따른 유동특성곡선의 차이에서 기인한 것이다. 항복응력과 소성점도의 결정은 전단변형에 의한 유동 입자들의 구조적 변화와 응력상태와 관련되기 때문이다. 세립토(< 0.075mm)를 다량 함유한 토석류의 유동성을 역해석하고자 할 때, 퇴적형상(흐름 양상, 퇴적층의 모양, 두께 및 길이 등)은 항복응력과 소성점도에 의해 결정된다. 항복응력과 소성점도는 액성지수의 함수로 나타낼 수 있으므로, 토석류의 발생가능지역에서 액성상태에 따른 토석류의 유동성을 평가할 지표로 활용할 수 있다.

• 소성∙가공
• /
• 제31권5호
• /
• pp.253-260
• /
• 2022

In this study, the microstructural characteristics of a high-speed-extruded Mg-5Bi-3Al (BA53) alloy and its tensile, compressive, and high-cycle fatigue properties are investigated. The BA53 alloy is successfully extruded at a die-exit speed of 16.6 m/min without any hot cracking using a large-scale extruder for mass production. The homogenized BA53 billet has a large grain size of ~900 ㎛ and it contains fine and coarse Mg₃Bi₂ particles. The extruded BA53 alloy has a fully recrystallized microstructure with an average grain size of 33.8 ㎛ owing to the occurrence of complete dynamic recrystallization during high-speed extrusion. In addition, the extruded BA53 alloy contains numerous fine lath-type Mg₃Bi₂ particles, which are formed through static precipitation during air cooling after exiting the extrusion die. The extruded BA53 alloy has a high tensile yield strength of 175.1 MPa and ultimate tensile strength of 244.4 MPa, which are mainly attributed to the relative fine grain size and numerous fine particles. The compressive yield strength (93.4 MPa) of the extruded BA53 alloy is lower than its tensile yield strength, resulting in a tension-compression yield asymmetry of 0.53. High-cycle fatigue test results reveal that the extruded BA53 alloy has a fatigue strength of 110 MPa and fatigue cracks initiate at the surface of fatigue test specimens, indicating that the Mg₃Bi₂ particles do not act as fatigue crack initiation sites. Furthermore, the extruded BA53 alloy exhibits a higher fatigue ratio of 0.45 than other commercial extruded Mg-Al-Zn-based alloys.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.270-276
• /
• 2009

After casting button-type small ingots of ternary Fe-Mn-S alloys which had three different Mn/S ratios (1, 5 and 70) in a vacuum arc furnace, the effect of the ratio on the sulfide formation was investigated. In case of the Mn/S ratio of 1, if alloy composition was located in an iron-rich corner on a Fe-Mn-S ternary phase diagram, only duplex MnS-FeS sulfide films were observed in the grain boundary. If the alloy composition was located in the miscibility gap area of the phase diagram, primary globular dendritic sulfides and dendritic sulfide slags were generated within the grain and tubular monotectic sulfides were also detected in the grain boundary. When the Mn/S ratio was 5, if the alloy composition was in the iron-rich corner, only bead-like sulfides were generated. On the other hand, if the composition was in the miscibility gap area, globular dendritic sulfides and dendritic sulfide slags were generated in the form of primary sulfide inclusions and rod-like eutectic sulfides were observed in the grain boundary. Especially, if the contents of Mn and S increased more in the miscibility gap area of the phase diagram, primary globular sulfides containing iron intrusions were observed. In case of Mn/S ratio of 70, if the contents of Mn and S was decreased in the Fe corner of the phase diagram, only bead-like sulfides were observed in the grain boundary. Despite the composition was outside the miscibility gap area of the phase diagram, if the contents of Mn and S increased, clusters of fine sulfide particles as well as fine spherical primary monophase sulfides were observed in the grain boundary.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.217-221
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occupied during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of high nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400 C and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.153-156
• /
• 2006

This study investigated influence of kind of fine aggregate on fundamental properties of concrete. For the properties of fluidity with various type of fine aggregate, lime stone crushed fine aggregate(Ls) exhibited favorable result, due to grain shape and particle distribution, and next was granite crushed fine aggregate(Gs), natural fine aggregate(Ns). Ns had the highest value of air content while Ls had the lowest, due to the effective filling performance by continuos particle distribution. Ls, Ns, Gs in an order had higher bleeding capacity and faster setting time. However, compressive and tensile strength value exhibited similar tendency, regardless of aggregate type.