• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.98-104
• /
• 2002

A study on microstructures of welds for Zircaloy-4 sheath end closure by the resistance upset welding methods was carried out. Two upset welding process variations such as magnetic farce and multi-impulse resistance welding were used. Grain size and microhardness across welds were analysed in terms of welding parameters. Magnetic farce resistance weld with one cycle of unbalanced mode has smaller upset length and $\alpha-grain$ size in heat affected zone than those of multi-impulse resistance weld because of lower heat input and shorter welding time. Heat affected zone formed by two upset resistance welding variations revealed fine Widmanstatten structure or martensitic ${\alpha}'$ structure due to the high heating rate and foster cooling rate. Magnetic force resistance welds showed recrystallized grains before grain growth, whereas multi-impulse resistance welds showed full grain growth.

• 한국표면공학회지
• /
• 제37권4호
• /
• pp.196-199
• /
• 2004

Seedlayers with low surface energy which increases the density of nucleation sites in the initial growth region of the recording layer deposited on them was studied to reduce grain size in recording layer. The seedlayer with low surface energy was so effective to attain finer grain in magnetic upper-layers. The Ni-Fe-O intermediate layer with low surface energy was found to be effective in reduction of grain size as well as magnetic cluster size of Co-Cr-Ta-Pt recording layer. Furthermore, the reduction of grain size in Co-Cr-Ta-Pt recording layer on Ni-Fe-O intermediate layer with low surface energy led to decrease the noise level in the high recording density region.

• 한국지형학회지
• /
• 제27권4호
• /
• pp.1-11
• /
• 2020

Coastal dunes play an important role in coastal defense. The Moraeul dune in Daecheongdo Island is representative in this regard. However, there is little knowledge, concerning the morphology, grain size, and formation timing of the dune. This study investigated the geomorphological characteristics of the Moraeul dune using topographic surveys, grain size analyses, and OSL dating. The dune was classified as 'single accreted foredune', which was developed under dense vegetation cover and efficient sand trapping. The dune consisted of fine to medium sand with 1.6Φ of mean grain size, and was covered with pine trees (> 100 years old). The samples from the upper part of the dune yielded quartz OSL ages ranging 0.5 ~ 0.7 ka. Therefore, it is likely that the dune developed at least before the Little Ice Age and became what it is today about one century ago.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.17-21
• /
• 1995

Tw types of Pb(Mn$\sub$1/3/Nb$\sub$2/3/)O$_3$+PZT Ceramics had been fabricated by hot-pressing method. One had cause grain and the other had fine grain doe to Cr$_2$O$_3$ addition. These specimen were poled by applying the DC electric field in various steps. The effects of thermal aging on their piezoelectric characteristics and temperature stability of the frequency were investigated.

• 산업기술연구
• /
• 제1권
• /
• pp.53-60
• /
• 1981

A study has been performed on the effect of TMT(thermomechanical treatment) on the mechanical properties of steel and aluminum alloys. Improvement of the mechanical properties on steel by HTMT is due to refinement of prior austenite grain size, martensite lath size and the distribution of fine carbide precipitates and on aluminum alloy by ITMT is due to grain size refinement, homogeneous distribution of small second phase particles and retardation of the recrystallization.

• 한국지구과학회지
• /
• 제33권4호
• /
• pp.350-359
• /
• 2012

30종의 초 중 고 및 대학교 교과서에 나타난 퇴적물의 입도에 대한 한국어 용어를 비교 검토하고 문제점과 대안을 제시하였다. 교과서에 나타난 퇴적물의 입도에 대한 한국어 용어는 거의 모두 Udden-Wentworth의 분류를 번역한 것으로, 교과서마다 다른 용어를 사용하고 있다. 자갈은 여러 교재에서 왕모래, 잔자갈, 왕자갈, 및 표력 또는 거력으로 나타내고 있으나, 이들은 각각 잔자갈(granule), 중자갈(pebble), 큰자갈(cobble), 및 왕자갈(boulder)로 나타내는 것이 적절한 것으로 생각한다. 자갈보다 작은 퇴적물은 '매우 고운', '고운', '중간', '굵은', 및 '매우 굵은'이라는 형용사를 각 퇴적물 이름 앞에 붙여서 표현하는 것이 적합한 것으로 생각된다. silt는 여러 교재에서 미사로 나타내고 있으나 실트로 표현하는 것이 적당하다고 판단된다. 실트와 점토의 혼합물인 mud는 대부분의 초등학교와 중학교, 그리고 일부 고등학교와 대학교 교과서에서 진흙으로 표현하고 있으나 한국지구과학 사전 등을 포함한 여러 교과서에서 쓰고 있는 바와 같이 이토(泥土)로 나타내는 것이 적당하다고 생각한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.306-309
• /
• 2009

The influence of equal-channel angular pressing (ECAP) route on dynamic deformation behavior of ultra-fine grained Al-4.4%Mg alloys was investigated in this study. The 8-pass ECAPed specimens consisted of ultra-fine grains of $0.5{\mu}m$ in size, and contained the considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. The result of dynamic torsional tests indicated that the maximum shear stress and fracture shear strain were lowest in the specimen deformed by ECAP via route A among the 8-pass ECAPed specimens. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity related to ECAP routes.

• 반도체디스플레이기술학회지
• /
• 제10권3호
• /
• pp.35-42
• /
• 2011

This paper describes the characteristics of high speed grinding and the influence of wheel surface speed V and a grindability of the grinding materials. The various fine ceramics pieces was ground by metal and vitrified bonded diamond wheel. The surface roughness of fine ceramics(Zirconia($ZrO_2$), Silicon Carbide(SiC), Silicon Nitride($Si_3N_4$), Alumina($Al_2O_3$)) decreases from $0.05{\mu}m(R_{max})$ to $0.025{\mu}m(R_{max})$ when the wheel speed at grinding point increases the wheel speed. Relation between the temperature at grinding point and surface roughness was linear. Abrasive jet machining(AJM), a specialized from of shot blasting, is considered one of the most helpful micro machining methods for hard and brittle materials such as glasses and ceramics by constant pressure grinding.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.124-125
• /
• 2020

In this study, the characteristics of fine aggregates produced according to the jaw crush crushing gap variation were studied and analyzed in terms of recycled aggregates, and the experiments were conducted in terms of grading, density, water absorption, unit volume weight, grain shape. It was shown that the quality of the fine aggregate was affected by the shape of the morphological crushing.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.60-61
• /
• 2020

In this study, the recycled fine aggregates produced from the waste concrete by using Jaw crusher depending on crushing gap of Jaw crusher were studied to offer a solution for recycled fine aggregate for concrete. The results of the experiment showed that the factors that influence grading and water absorption ratio, density and grain shape were significantly characterized by the generation of the particulate matter and the crushing shape of the aggregate.