• 한국재료학회지
• /
• 제11권9호
• /
• pp.751-758
• /
• 2001

Anatase $TiO_2$ thin films as a photocatalyst were prepared by the D.C reactive magnetron sputtering process. The $TiO_2$ thin films were deposited on Si(100) substrates under the various conditions : oxygen partial pressure, working pressure, substrate temperature, D.C power, and deposition time. The morphology of the TiO$_2$ thin films showed an island structure. At early stages of film growth, amorphous phase formed. However, during the further growth, columnar crystalline $TiO_2$grains evolved. The crystallinity of the thin films depended on the oxygen partial pressure, the working pressure and the D.C. powers.

• 한국표면공학회지
• /
• 제37권3호
• /
• pp.169-174
• /
• 2004

MgO thin films were reactively deposited using an internal inductively coupled plasma assisted sputtering method varying reactive gas ratio to get stoichiometric film composition, and bipolar dc substrate bias to suppress micro arcs. The minimum frequency required for arc suppression was about 10KHz depending on ICP power. Their crystallinity was analyzed using X-ray diffraction and surface morphology using AFM. The surface was very smooth with rms roughness less than 0.42nm. The preferred orientation of the films were changing from (200) to bulk-like characteristics as Ar: $O_2$ratio was controlled to 10 : 2. Optical emission spectroscopy revealed that there were two distinct discharge modes: a blue one and a green one, where enhanced emission from Ar and Mg were observed. This cannot simply be understood by metallic or oxide mode of reactive sputtering due to ICP coupled to magnetron discharge.

• 전자통신동향분석
• /
• 제3권4호
• /
• pp.3-12
• /
• 1988

Epilayer growing process has been recognized as a key technology for successful GaAs based devices and integrations. These may include HEMT, multiple quantum well structures, band gap engineering, and quantum confinement heterostructures. The fabrication of epilayers in these devices must meet very stringent requirements in terms of crystallinity, composition, film thickness and interface quality. In particular, the quality of interfaces is getting more important because the film thickness, and flatness, roughness and stability at interface of ultrathin films cause critical effects on the device performance. This article reviews the current status of modern epitaxial techniques which have been developed in the last few years. First, the new techniques PLE, GI, MEE, TSL based on MBE technique will be reviewed and their technical importance will be stressed. Secondly, MOMBE, GSMBE, CBE which combine the advantages of MBE and MOCVD will also be discussed. Thirdly, the new sophisticated epitaxial technique, ALE, of which mechanism is totally different from others, will also be reviewed. Finally, areas which should be exploited more extensively to accomplish these techniques will be addressed.

• 한국세라믹학회지
• /
• 제33권9호
• /
• pp.969-976
• /
• 1996

RuO2 thin films were deposited on SiO2(1000 $\AA$)/Si by hot-wall Metal Organic Chemical Vapor Depositon. The crystallinity of RuO2 thin films increased with increasing deposition temperature and the preferred orienta-tion of RuO2 films converted (200) plane to (101) plane with increasing film thicknesses. Such a change in preferred orientation was influenced on the crystallographic structure and the residual stress of RuO2 thin films. The resistivity of the 2700$\AA$-thick RuO2 thin films deposted at 30$0^{\circ}C$ was 52.7$\mu$$\Omega$-cm and they could be applicable to bottom electrodes of high dielectric materials. However the resistivity of RuO2 thin films increased with decreasing film thicknesses. The grain size and the resistivity of RuO2 thin films were densified with increasing the annealing temperature and showed the decrease of resistivity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1433-1436
• /
• 2009

Film morphology, crystallinity, and luminescence property of solution processed ZnO films have been studied. Fluorine addition and annealing ambient significantly change the defect-related emission band as well as the structural property. Using the overall emission behaviors, we can predict an optimized process condition for solution-based ZnO thin film.

• Applied Science and Convergence Technology
• /
• 제26권2호
• /
• pp.30-33
• /
• 2017

ZnO thin films which were deposited by RF magnetron sputtering system were annealed by furnace and insitu heat treatment methods. We investigated the effect of heat treatment method on physical properties of ZnO thin films. The structural and optical properties of ZnO thin films were improved by heat treatment. Through the annealing treatment of ZnO film by furnace, the good crystallinity and ultraviolet emission were obtained. These results are attributed to the improved formation of Zn-O bond in ZnO thin film annealed at by furnace. We confirm that the formation of Zn-O bond plays an important role in obtaining the excellent structural and optical properties of ZnO thin films.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1313-1314
• /
• 2006

The polycrystalline 3C-SiC thin films heteroepitaxially grown by LPCVD method using single precursor 1,3-disilabutane at $850^{\circ}C$. The crystallinity of the 3C-SiC thin film was analyzed by XRD and FT-IR. Residual strain was investigated by Raman scattering. The surface morphology was also observed by AFM and voids or dislocations between SiC and $SiO_2$ were measured by SEM. The grown poly 3C-SiC thin film is very good crystalline quality, surface like mirror, and low defect and strain. Therefore, the polycrystalline 3C-SiC is suitable for harsh environment MEMS applications.

• 한국안전학회지
• /
• 제11권1호
• /
• pp.67-74
• /
• 1996

In order to investigate the effect and reliability coming up to properties of the matter due to the change of solid structure in dielectrics, the effect of dielectric characteristics for thermal treated LDPE film was made researches. Specimens of LDPE with thickness 100 [$\mu\textrm{m}$] were investigated into the change of solid structure by ageing. Thermal treated specimen were made, that were after applying heat at 100 [$^{\circ}C$] for 1 [hour] \circled1 air-cooled specimen slowly, \circled2 water-cooled specimen under the ,com temperature, \circled3 liquid nitrogen gas-cooled specimen rapidly. With specimen of thermal treated three types turn out and original, it was for dielectric characteristics to be experimented in the temperature range of 20~120 [$^{\circ}C$], frequency range of 30~1.5${\times}10^5/$[Hz], appling voltage from 300 to 1500[㎷]. Consequently, the degree of crystallinity was changed with 49~57 [%] according to the thermal treatment. In case of frequency, 100 [Hz], on the thermal dependance in dielectric characteristics, tan decreases due to cooling method.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.408-409
• /
• 2006

The polycrystalline 3C-SiC thin films heteroepitaxially grown by LPCVD method using single precursor 1. 3-disilabutane at $850^{\circ}C$. The crystallinity of the 3C-SiC thin film. was analyzed by XPS. Residual strain was investigated by Raman scattering. The surface morphology and voids between SiC and $SiO_2$ were measured by SEM. The grown poly 3C-SiC thin film is very good crystalline quality, surface like mirror, and low defect and strain. Therefore, the polycrystalline 3C-SiC is suitable for harsh environment MEMS applications.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.406-409
• /
• 1999

Thin films of silver with high reflectance of 95% and above were fabricated successfully on polyester substrate by using e-beam evaporation processes. The optimum process condition was investigated by varying the current values applied while keeping the substrate temperature at room temperature by circulating the cooling water around it during deposition. Thin films of silver deposited with 30 mA as current revealed the highest reflectance of 96.4%, while being illuminated with a light of 700nm wave-length. But their adhesion showed unsatisfactory results. Though the films showed a condensation type in the cross-sectional views, they revealed crystallinity in the planes of (111) and (200) and growth orientation in <100> direction.