• Advances in pediatric surgery
• /
• v.7 no.2
• /
• pp.118-125
• /
• 2001

The effectiveness of operative and non-operative management for postoperative adhesive ileus in children has been discussed. This study reviews the clinical characteristics and the treatment consequences of adhesive ileus in our institution. Department of Surgery of Chunbuk National University Hospital, retrospectively. A total of 62 cases of post-operative small bowel obstruction treated between January 1975 and December 1998 under the 15 years of age are included in this study. The patients were divided into two groups, operative(n=26) and non-operative(n=36) groups. The prevalent age was between 11 and 15 years(28 cases; 45.2 %), and the most common previous operation was appendectomy(28 cases; 45.2 %). The most common operative procedures were adhesiolysis(17 cases; 65.4 %). The interval between admission and operation was 1 day in 11 cases(42.3 %). The most common site of adhesion was the ileum in 13 cases(50.0 %) and band constriction was the most frequent pattern(8 cases; 30.8 %). Intestinal resection was significantly high in delayed operations of more than four days, in the patients with three or more classical signs of strangulation(fever, tachycardia, leukocytosis, abdominal pain, rebound tenderness), and in the cases of complete obstruction on plain abdomen film(p < 0.05). In conclusion, operation should be considered in cases with three or more signs of strangulation, no clinical improvement for over four days of conservative treatment, and signs of complete obstruction on plain abdomen film during the observation periods.

• Korean Journal of Microbiology
• /
• v.12 no.3
• /
• pp.147-148
• /
• 1974

A small amount of Duco cement or Elmer's clear cement was dropped on a slide glass and immediately spread with a glass rod or woden stick a thin film on the surface. After approximately 1 minute a small amount of rubber cement was spread on the top of the film of Duco cement using the same method as described earlier. It was important that the rubber cement be smeared before the Duco cement dried out. These two kinds of cements must not be mixed. It was better to make the film of the rubber cement slightly thicker than the film of Duco cement. This composite film may be used up to several months after preparation. The sample leaf was placted on the slide, prepared with adhesive and the leaf surface was passed on the film with the thumb. The pressing was done so the leaf surface was completely in contact with the film. Then the leaf was peeled from the slide.

• Membrane Journal
• /
• v.25 no.6
• /
• pp.530-537
• /
• 2015

Photovoltaic (PV) modules are environmentally energy conversion devices to generate electricity via photovoltaic effect of semiconductors from solar energy. One of key elements in PV modules is "Backsheet," a multilayered barrier film, which determines their lifetime and energy conversion efficiency. The representative Backsheet is composed of chemically resistant poly(vinyl fluoride) (PVF) and cheap poly(ethylene terephthalate) (PET) films used as core and skin materials, respectively. PVF film is too expensive to satisfy the market requirements to Backsheet materials with production cost as low as possible. The promising alternatives to PVF-based Backsheet are hydrocarbon Backsheets employing semi-crystalline PET films instead of PVF film. It is, however, necessary to provide improved barrier property to water vapor to the PET films, since PET films are suffering from hydrolytic decomposition. In this study, a polyurethane adhesive with reduced water vapor permeation behavior is developed via a homogeneous distribution of hydrophobic silica nanoparticles. The modified adhesive is expected to retard the hydrolysis of PET films located in the core and inner skin. To clarify the efficacy of the proposed concept, the mechanical properties and electrochemical PV performances of the Backsheet are compared with those of a Backsheet employing the polyurethane adhesive without the silica nanoparticles, after the exposure under standard temperature and humidity conditions.

• Structural Engineering and Mechanics
• /
• v.58 no.2
• /
• pp.301-326
• /
• 2016

An optimization method of patch shape was developed in this study, in order to improve repair of cracked plates. It aimed to minimize three objectives: stress intensity factor, patch volume and shear stresses in the adhesive film. The choice of these objectives ensures improving crack repair, gaining mass and enhancing the adhesion durability between the fractured plate and the composite patch. This was a multi-objective optimization combined with Finite elements calculations to find out the best distribution of patch height with respect to its width. The implementation of the method identified families of optimal shapes with specific geometric features around the crack tip and at the horizontal end of the patch. Considerable mass gain was achieved while improving the repair efficiency and keeping the adhesive shear stress at low levels.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.1
• /
• pp.1-12
• /
• 1992

In order to improve adhesive force of TiN film, we sputtered titanium as interlayer before TiN deposition by Plasma Enhanced Chemical Vapour Deposition. We observed changes of hardness and adhesion at a various thickness of titanium interlayer and also examined analysis. At the critical thickness of the titanium interlayer(about $0.2{\mu}$), adhesive force of TiN films were promoted mostly. But over the critical thickness, a marked reduction of adhesive force was showed, because of the internal stress of titanium interlayer. From AES analysis, the adhesion improvement of TiN films was mainly caused by nitrogen diffusion into titanium interlayer during TiN deposition process which relieved stress concentration at TiN coating-substrate interface.

• Elastomers and Composites
• /
• v.25 no.3
• /
• pp.195-202
• /
• 1990

Rubber-modified polyurethane resin which was prepolymer type terminated with NCO, was synthesized by reacting isocyanate groups[NCO] and hydroxyl groups[OH]. Polybutadiene rubbers which had OH groups in the side of rubber chains, were charged at ratio $0%{\sim}40%$ of solid component in reactants. For products, physical properties were investigated experimentally. The results abtained in experiment were as follows. 1. Liquid resin and dried film was good solubility and clearity at less than 25%, 20% of rubber without being related to sort. 2. G-1000 showed better properties than R-45HT in solubility, dring time and adhesive strength. 3. Dring time and adhesive strength were considerably influenced by molecular weigh and structure of rubber. 4. In using 25% of mixed rubber(G-1000/R-45HT=50/50), It represented best properties in dring time(10 minute) and adhesive strength($23Kg/cm^2$).

• Composites Research
• /
• v.17 no.6
• /
• pp.14-21
• /
• 2004

Failure process, mode and strength of unidirectional composite single lap bonded joints were investigated experimentally with respect to bonding methods, those are, co-curing with and without adhesive and secondary bonding. The co-cured joint specimens without adhesive had the largest failure strength. Progressive failures along the adhesive layer occurred in the secondary bonded specimens. In the co-cured specimens with adhesive film which had better material strength and adhesion performance, delamination failure occurred and the joint strengths were less than those of secondary bonded specimens. Delamination failure did not occur in the secondary bonded specimens because of earlier crack growth and progressive failure in the adhesive layer. Therefore, failure strength of composite bonded Joints were not always proportionate to material strength and adhesion performance of the adhesive due to the weakness of delamination in composite materials. The effects of surface roughness, bondline thickness and fillets were also studied on secondary bonded specimens.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.177-179
• /
• 2011

The purpose of this study is to enhance an adhesion between substrate and Diamond-like Carbon (DLC) film. DLC has many outstanding properties such as low friction, high wear resistance and corrosion resistance. However, it is difficult to achieve enough adhesion because of weak bonding between DLC film and the substrate. For improvement adhesion, a layer between DLC film and the substrate was prepared by dual post plasma. DLC film was deposited on nitrided layer by linear ion source. The composed compound layer between substrate and DLC film was investigated by Glow Discharge Spectrometer (GDS) and Scanning Electron Microscope (SEM). The synthesized bonding structure of DLC film was analyzed using a micro raman spectrometer. Mechanical properties were measured by nano-indentation. In order to clarify the mechanism for improvement in adhesive strength, it was observed by scratch test.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.6
• /
• pp.307-314
• /
• 2021

Diamond-like carbon (DLC) is difficult to achieve sufficient adhesion because of weak bonding between DLC film and the substrate. The purpose of this study is to improve the adhesion between substrate and DLC film. DLC film was deposited on AISI H13 using linear ion source. To improve adhesion, the substrate was treated by dual post plasma nitriding. In order to define the mechanism of the improvement in adhesive strength, the gradient layer between substrate and DLC film was analyzed by Glow Discharge Spectrometer (GDS) and Scanning Electron Microscope (SEM). The microstructure of the DLC film was analyzed using a micro Raman spectrometer. Mechanical properties were measured by nano-indentation, micro vickers hardness tester and tribology tester. The characteristic of adhesion was observed by scratch test. The adhesion of the DLC film was enhanced by active screen plasma nitriding layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.177-180
• /
• 2004

In this study, we report a novel encapsulation method for longevity of an organic thin-film transistor (OTFT) using pentaceneby means of an adhesive multiplayerincluded Al film. For encapsulation of OTFTs, the Al film adhered onto the OTFT in a dry nitrogen atmosphere using a proper adhesive. A lifetime, which was defined as the time necessary to reduce mobility to 2% of initial mobility value, was observed from the typical $I_{D-VD}$ characteristics of the field-effect transistor (FET). The initial field effect mobility ${\mu}$ was measured to be $2.0{\times}10^{-1}\;cm^2/Vs$. The characterization was maintained for long times in air. No substantial degeneration occurred. The performance and the stability are probably due to the encapsulation effect.