• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.197-200
• /
• 2001

A manufacturing process of composite pressure vessel was studied. The vessel was fabricated using the filament winding process. It is utilized as a container of high pressure Helium gas which propels a rocket fuel and an oxidizer. The layup patterns were determined based on the lamination theory. 3-axis controlled filament winding machine was developed to realize the patterns. The vessel was successfully fabricated using the developed machine. And the hydraulic pressure test was performed to measure an applied pressure-strain relations on the composite vessel.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.308-313
• /
• 2002

It is known that the composite material shafts using on small boats have various advantages comparing to forged steel shafts, fur examples, specific strength, fatigue strength, corrosion, etc. The analysis of the stresses and strains in the composite material shafts made by filament winding method is presented in this paper. The classical laminated plate theory is applied on the patch cut from the composite material hollow shafts. It is verified that the composite material hollow shafts of diameter 40 mm is the most optimum when the ratio of the inner diameter to the outer is 0.4 and winding angle is 45$^{\circ}$. It is also proven that the shear strain does not change seriously between 30$^{\circ}$and 60$^{\circ}$of winding angles. It is dangerous when the winding angle is over 75$^{\circ}$because the values of shear strain and stress produced on the shaft are too high so it must be avoided to wind the filament by the angle over 75$^{\circ}$.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2059-2065
• /
• 2008

In this paper, quasi-static crushing tests of composite circular tubes under axial compression load are conducted to investigate the energy absorption characteristics. Circular tubes used for this experiment are glass/epoxy (GFRP) composite tubes, which is fabricated by the filament winding method. One edge of the composite tube is chamfered to reduce the initial peak load and to prevent catastrophic failure during crushing process. Two suggested trigger mechanisms for the composite tubes are investigated. Crushing modes are mainly affected by thickness/diameter ratio, and average crushing loads are mainly affected by their cross-sections. Energy absorption characteristics vary significantly as a function of the tube geometry, trigger mechanism, t/D ratio and the cross-sectional shape.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.140-145
• /
• 2001

The purpose of this study is the design of composite shaft which is wound by Filament Winding method. Classical laminated plate theory was used for analyzing the stress, and for structure design. The diameter and thickness of composite shaft were calculated by this theory. The result that if tensile stress was zero, torsion stress was a certain value below 0.4(diameter rate) and torsion strength was the highest value on 45$^{\circ}$(winding angle). In case of 90$^{\circ}$(winding angle), we have to consider the torsional moment when the composites shaft was load.

• 연구논문집
• /
• s.30
• /
• pp.129-135
• /
• 2000

Double boss type composite pressure bottles have been developed widely but single boss type had not because there are some difficulty in technical point. In this paper a research was performed to develop composite pressure vessel in conjunction with design, fabrication, and test. Fiber pattern and angles were decided by CADFIL software and they are [liner/$15^{\circ}$/$15^{\circ}$/$90^{\circ}$/$18^{\circ}$/$90^{\circ}$/$21^{\circ}$/$21^{\circ}$/$90^{\circ}$]. Fabrication of bottles was done by AEA's 5-axis filament winding machine. During fabrication fiber optic sensor were embedded to measure were behavior of structure at the applied internal pressure. Even though satisfied test results were not obtained, the experimental set-up of fiber optics showed the possibility for the application of filament wound vessels. However, the conventional strain and fabrication of single boss composite bottles.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.203-207
• /
• 2000

Filament Winding Process is a comparatively simple operation in which continuous reinforcements in the form of roving are wound over a rotating mandrel. And now well established as a versatile method for storage tanks and pipe for the chemical and other industries . In this study, tensile strength of a filament wound ring specimens were evaluated by split disk test fixture and dress disk test fixture , The results obtained from experiments were compared with the theoretical values obtained by the rule of mixtures. And the purpose of this paper is the suggestion of an appropriate test method for the evaluation of tensile properties of filament wound structures .The tensile strength of a ring specimen tested by the dress disk test showed better agreement with the theoretical values than of a ring specimen tested by the split disk test because the stress concentration in edges of a split disk test fixture is more severe than that of dress disk test fixture. The results showed that the tensile strength of a ring specimen was influenced by the geometry of test fixture, the continuity of fibers, fiber-tension, fiber-end and stress concentration in specimen.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.53-56
• /
• 1999

헬기 로터깃은 최초로 항공기의 일차구조물로 사용된 대형 복합재료구조물이다. 헬기 로터깃은 운용기간(service life)동안에 $10^{7}$이나 $10^{8}$의 high-cycle 피로환경을 경험가게 된다. 로터깃은 복합재료가 알맞게만 사용된다면 거의 무한대의 피로수명을 갖게된다고 알려져 있다.

• Composites Research
• /
• v.16 no.2
• /
• pp.1-8
• /
• 2003

Thus paper summarizes the procedures to develop the downscaled payload kick motor for KSR-III by KARI. Filament winding-a well-known method of manufacturing composite motor case - is adopted to reduce structural weight. Netting and lamination theories are used to determine adequate winding thickness under required internal pressure. Dome shapes are designed considering feasible winding patterns and easiness of mandrel manufacturing. T-800 carbon fiber and Novolac type resin are selected for weight-reduction. The separate mandrels are disassembled and removed after filament winding. The manufacturing process of real payload kick motor is developed from the design experience of downscaled ones.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.359-363
• /
• 2013

Silicon carbide and its composites are being considered as a nuclear fuel cladding material for LWR nuclear reactors because they have a low neutron absorption cross section, low hydrogen production under accident conditions, and high strength at high temperatures. The SiC composite cladding tube considered in this study consists of three layers, monolith CVD SiC - $SiC_f$/SiC composite -monolith CVD SiC. The volume fraction of SiC fiber and surface roughness of the composite layer affect mechanical and corrosion properties of the cladding tube. In this study, various types of SiC fiber preforms with tubular shapes were fabricated by a filament winding method using two types of Tyranno SA3 grade SiC fibers with 800 filaments/yarn and 1600 filaments/yarn. After chemical vapor infiltration of the SiC matrix, the surface roughness and fiber volume fraction were measured. As filament counts were changed from 800 to 1600, the surface roughness increased but the fiber volume fraction decreased. The $SiC_f$/SiC composite with a bamboo-like winding pattern has a smaller surface roughness and a higher fiber volume fraction than that with a zigzag winding pattern.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.203-206
• /
• 2005

The objective of study on composite cylinder for alternative fuel vehicle is to develop safe, efficient, and commercially viable, on-board fuel storage system for the fuel cell vehicle or natural gas vehicle that use highly compressed gaseous fuel such as hydrogen or natural gas. This study presents the whole procedure of development and certification of a type 3 composite cylinder of 207bar service pressure and 70 liter water capacity, which includes design/analysis, processing of filament winding, and validation through various testing and evaluation. Design methods of liner configuration and winding patterns are presented. Three dimensional, nonlinear finite element analysis techniques are used to predict burst pressure and failure mode. Design and analysis techniques are verified through burst and cycling tests. The full qualification test methods and results for validation and certification are presented.