• 한국구조물진단유지관리공학회 논문집
• /
• 제25권3호
• /
• pp.31-39
• /
• 2021

본 연구에서는 후크형 강섬유(HSF)와 스무스형 섬유(SSF)의 혼합 비율과 변형속도가 하이브리드 섬유보강 시멘트복합체의 인장 특성 시너지 효과에 미치는 영향을 평가하기 위하여, HSF와 SSF를 각각 1.5+0.5, 1.0+1.0, 0.5+1.0vol.%의 혼합 비율로 혼입한 하이브리드 섬유보강 시멘트복합체를 제작하였다. 실험 결과, HSF를 보강한 시멘트복합체(HSF2.0)은 변형속도가 증가함에 따라 섬유 주변 매트릭스에 발생하는 마이크로 균열의 증가에 의해 직선형으로 인발되는 섬유의 수가 감소하고, 인장강도 점 이후 응력 저하가 급격하게 발생하였다. SSF가 0.5vol.% 혼입되는 경우, 준정적에서 마이크로 균열을 효과적으로 제어하지만, 고속에서는 마이크로 균열 제어 및 후크형 강섬유의 인발저항성능 향상에 효과적이지 않은 것으로 확인되었다. 반면, HSF 1.0vol.%와 SSF 1.0vol.%를 혼입한 시험체(HSF1.0SSF1.0)은 마이크로 및 매크로 균열에 대해 각각의 섬유가 효과적으로 제어하고, SSF가 HSF의 인발저항성능을 향상시킴으로써 고속에서 변형능력 및 에너지 흡수 능력에 대한 섬유 혼합 효과가 크게 증가하였으며, 인장강도, 변형능력 및 피크인성의 변형속도 민감도가 가장 높은 것으로 나타났다. 반면, SSF 1.5vol.%의 혼입은 매트릭스 내의 섬유 혼입 개체 수를 증가시키고, HSF의 인발저항성능을 향상시켜 가장 높은 인장강도 및 연화인성 시너지 효과를 나타내었지만, 매크로 균열을 제어하는 HSF의 혼입률이 0.5vol.%로 낮아 변형능력 및 피크인성 시너지에는 효과적이지 않은 것으로 확인되었다.

• Advances in concrete construction
• /
• 제8권4호
• /
• pp.247-255
• /
• 2019

Several reinforced concrete structures that get deteriorated by rebar corrosion are retrofitted using Carbon Fiber Reinforced Polymer (CFRP). When rebar comes in direct contact with CFRP, rebar may corrode, as iron is more active than carbon. Progression of corrosion of rebar in strengthened RC structures has been carried out when rebar comes in direct contact with CFRP. The experimentation is carried out in two phases. In phase I, corrosion of bare steel bar is monitored by making its contact with CFRP. In phase II, concrete specimens with surface bonded CFRP were casted and subjected to the realistic exposure conditions keeping direct contact between rebar and CFRP. Progression of corrosion has been monitored by various parameters: Half-cell potential, Tafel extrapolation and Linear Polarisation Resistance. On termination of exposure, to find residual bond stress between rebar and concrete, pull-out test was performed. Rebar in contact with CFRP has shown substantially higher corrosion. The level of corrosion will be more with more area of contact.

• Computers and Concrete
• /
• 제19권4호
• /
• pp.375-385
• /
• 2017

In the present paper experimental and numerical analysis of hook-ended steel fiber reinforced concrete is carried out. The experimental tests are performed on notched beams loaded in 3-point bending using fiber volume fractions up to 1.5%. The numerical analysis of fiber reinforced concrete beams is performed at meso scale. The concrete is discretized with 3D solid finite elements and microplane model is used as a constitutive law. The fibers are modelled by randomly generated 1D truss finite elements, which are connected with concrete matrix by discrete bond-slip relationship. It is demonstrated that the presented approach, which is based on the modelling of concrete matrix using microplane model, able to realistically replicate experimental results. In all investigated cases failure is due to the pull-out of fibers. It is shown that with increase of volume content of fibers the effective bond strength and slip capacity of fibers decreases.

• 한국지진공학회논문집
• /
• 제13권1호
• /
• pp.9-16
• /
• 2009

철근 콘크리트 부재에서 부착강도는 콘크리트와 보강근 사이에 중요한 요소 중 하나이다. 본 연구는 인발실험을 통해 AFRP 보강근의 부착강도에 대하여 실험하고, AFRP 보강근과 이형철근의 부착특성을 비교하여 나타내었다. 묻힘 길이와 보강근의 직경이 실험의 변수로 사용되었으며, 실험을 통해서 AFRP 보강근의 부착응력-미끌림 관계 및 파괴양상을 평가하였다. AFRP 보강근의 부착응력-미끌림 관계는 이형철근과 비슷한 양상을 보였으며, 보강근의 직경이 증가할수록 인발하중은 증가하나 부착응력은 비슷한 결과를 보였다. AFRP 보강근의 부착강도는 이형철근의 약 54%에 달하는 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.327-332
• /
• 2001

It is generally observed that steel fiber reinforced concrete with traditional straight steel fibers overcomes brittle nature of plain concrete by failure mechanisms by fiber pull-out rather than fiber rupture resulting from fiber yielding or concrete fracture at failured surface. Ring type steel fibers in concrete which is confined in concrete matrix and has better orientation, thus, lead to fiber yielding and concrete fracture as well as increase of flexural behavior of concrete more efficiently, Comparative experimental study is performed in order to measure the relative efficiencies of steel fiber reinforced concrete reinforced with two different fibers. It is found that better toughness is obtained from the ring type steel fiber reinforced concrete than from straight steel fiber reinforced concrete under flexural loading.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2017년도 추계 학술논문 발표대회
• /
• pp.79-80
• /
• 2017

This study examined the effect that the amorphous metallic fibers had on the static mechanical properties and the impact resistance of cement composites to those of hooked steel fibers. The hooked steel fiber exhibited pull-out from the matrix after the peak flexural stress was attained, while the amorphous metallic fiber was not pulled out from the matrix, but was instead cut off. In terms of impact resistance, the amorphous metallic fiber reinforced cement composite was found to be more effective at resisting cracking than the hooked steel fiber reinforced cement composite. Therefore, amorphous metallic fiber should be used in fiber reinforced cement composite materials, and for structural materials, and for protection panels.

• The Korean Journal of Ceramics
• /
• 제7권2호
• /
• pp.74-79
• /
• 2001

Alumina composite reinforced by chopped alumina fiber was fabricated by filter-pressing the fiber slurry followed by the infiltration of alumina slurry. The chopped fiber was coated with nickel by electroless plating method. The green samples were densified by hot-pressing. Microstructures were studied by SEM and the mechanical properties such as bending strength and fracture toughness were measured. The resulting mechanical properties were analyzed in relation with processing parameters such as preform density and resulting microstructures. The load-displacement curve of the specimen with Ni interlayer but without Ni inclusion showed brittle fracture mode due to the direct contact between matrix and fiber. The load-displacement curve of the specimen with Ni interlayer and Ni inclusion in the matrix which is introduced by high applied pressure during specimen preparation showed non-brittle fracture mode due to the fiber pull-out and dutile phases in the matrix.

• Structural Engineering and Mechanics
• /
• 제5권4호
• /
• pp.355-368
• /
• 1997

Fiber reinforced plastic (FRP) rods are used as reinforcement (prestressed or not) to concrete. FRP composites can also be combined with steel to form hybrid reinforcing rods that take advantage of the properties of both materials. In order to effectively utilize these rods, their bond behavior with concrete must be understood. The objective of this study is to characterize and model the bond behavior of hybrid FRP rods made with epoxy-impregnated aramid or poly-vinyl alcohol FRP skins directly braided onto a steel core. The model closely examines the split failure of the concrete by quantifying the relationship between slip of the rods resulting transverse stress field in concrete. The model is used to derive coefficients of friction for these rods and, from these, their development length requirements. More testing is needed to confirm this model, but in the interim, it may serve as a design aide, allowing intelligent decisions regarding concrete cover and development length. As such, this model has helped to explain and predict some experimental data from concentric pull-out tests of hybrid FRP rods.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.160-163
• /
• 1999

The mechanical properties and failure behaviour of carbon/phenolic composites were inverstigated by tension and compression. Carbon/phenolic composites were fabricated by infiltration of matrix into 8 harness satin woven fabric of PAN-based carbon fibers. The tensile and compressive tests were performed at 25℃ under air atmosphere and, at 400℃ and 700℃ under N₂ atmosphere. The tensile strengths of carbon/phenolic composites in with-laminar/0° warp direction were about 10 times higher than those in with-laminar/45° warp direction, which was analyzed due to a change of fracture mode from fiber pull-out by shear to tensile fracture of fibers. The fracture of carbon/phenolic composites in with-laminar/45° direction was analyzed due to delamination by buckling. Tensile and compressive strength of carbon/phenolic composites decreased to about 50% at 400℃, and to about 10% at 700℃ compared to that at room temperature. The main reason for the decrease of tensile or compressive strength with increasing temperature was analyzed due to a reduction of bond strength between fibers and matrix resulting from thermal degradation of phenolic resin.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.250-258
• /
• 2000

The reinforcing effects of ductile short-fiber reinforced brittle matrix composites are studied by, measuring flexural strength, fracture toughness and impact energy as functions of fiber volume fraction and length. The parameters of fracture mechanics, K and J are applied to assess fracture toughness and bridging stress. It is found that fracture toughness is greatly, influenced by the bridging stress ill which fiber pull-out is occur. For the reinforcing effects as functions of fiber volume fraction($V_f$ = 1, 2, 3 %) and length(L = 3, 6. 10cm), the flexural strength is maximum at $V_f$ = 1% and both fracture toughness.