• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.531-532
• /
• 2002

This paper present a gain-clamped L-band EDFA based on reflecting back a portion of backward amplified spontaneous emission into the erbium-doped fiber section, utilizing a fiber Bra99 grating. By using FBG with R=66.1 and 99.9%, the gain is clamped at 15.1 and 14.3㏈, respectively, with a variation of less than 0.2㏈ for an input signal power as high as -5 ㏈m. However, a small noise figure penalty is obtained, which is the consequence of the gain clamping effect.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.163-166
• /
• 2000

Fiber Bra99 grating (FBG) sensor, one of the fiber optic sensor (FOS) offers lots of advantages for structural health monitoring due to its multiplexing capability. Also, it is proper to measure the structural vibration with no mass concentration effect. In this paper, we constructed two sensor arrays composed of 9 FBG sensors for the vibration and mode sensing of a composites beam. For an accurate measurement of wavelength shift, a signal processing board with an electric circuit based on time-interval counting was developed. This sensor system showed a good resolution of dynamic strain (<10${\mu}{\varepsilon}$). Using this sensor system, dynamic strains at 9 points of composite beam was measured and strain measured mode shape of the beam was calculated from the acquired strains and compared with numerical results by ABAQUS.

• Journal of the Optical Society of Korea
• /
• v.6 no.2
• /
• pp.44-47
• /
• 2002

In this paper, we propose and demonstrate a novel channel-selectable multichannel optical add/drop multiplexer consisting of a sampled fiber grating and tunable fiber Bra99 gratings. The device adds and drops not only single channel, but also any predetermined multiple channels simultaneously with low interchannel crosstalk by wavelength tuning as small as 0.5 nm or less. The interchannel crosstalk better than 27㏈ has been shown experimentally.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.299-307
• /
• 2009

Emerging fiber optic sensor technologies have shown great potential to overcome the difficulties associated with conventional sensors. Fiber optic sensors are immune to EM noise and electric shock and thus can be used in explosion-prone areas. Several kinds of fiber optic sensors have been developed over the last two decades to take advantage of these merits. There have also been many field applications of fiber optic sensors for structural health monitoring as NDT/HDE. However, very few sensors, particularly a load cell have been successfully commercialized. This Paper Presents a load cell using fiber Bra99 gra1ing (FBG) sensors. The shape of the load cell is a link type, and three FBG sensors are used for measuring strains at three different points. Especially, these strains are processed with a differential method in order to exclude common mode noise such as temperature. Moreover, the sensitivity, the linearity and the resolution of the load cell were successfully verified from the experiment of tension test.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.501-505
• /
• 2002

We have numerically analysed the effects of the light sourer spectral power distortion in an optical CDMA system using PN codes and FBGI for ultra-fast multi-access optical networks. The interference between two CDMA channels decreases with an increase in the code length and the .simultaneous access number is equal to the code length in the region of 0 to 15% spectral power distortion. As a result, the spectral power distortion with optical spectrum is very important in designing the optical CDMA systems.

• Composites Research
• /
• v.14 no.6
• /
• pp.47-58
• /
• 2001

This paper describes applications of cure monitoring techniques by using embedded fiber optic strain sensors, which are extrinsic Fabry-Perot interoferometric (EFPI) and/or fiber Bra99 grating (FBG) sensors, to three kinds of molding methods of autoclave, FW and RTM molding methods. In these applications, internal strain of high-temperature curing resin was monitored by EFPI sensors. From theme experimental results, it was shown that strain caused by thermal shrink at cooling stage could be measured well. In addition, several specific matters to these molding methods were considered. As thor an autoclave molding of unidirectional FRP laminates, it was confirmed that off-axis strain of unidirectional FRP could be monitored by EFPI sensors. As for FW molding using room-temperature (RT) cured resin, it was found that the strain outputs from EFPI sensors represented curing shrinkage as well as thermal strain and the convergence meant finish of cure reaction. It was also shown that this curing shrinkage should be evaluated with consideration on logarithmic change in stiffness of matrix resin. As for a RTM melding, both EFPI and FBC sensors were employed to measure strain. The results showed that FBG sensors hale also good potential for strain monitoring at cooling stage, while the non-uniform thermal residual strain of textile affected the FBG spectrum after molding. This study has proven that embedded fiber optic strain sensors hale practical ability of cure monitoring of FRP. However, development of automatic installation methods of sensors remains as a problem to be solved for applications to practical products.