• Journal of the Optical Society of Korea
• /
• v.7 no.1
• /
• pp.38-41
• /
• 2003

We present an analysis of highly-dispersive guided modes of two-dimensional photonic crystal waveguides. By the plane ave expansion method, band structures and mode profiles of two-dimensional photonic crystal waveguides are obtained. It is found that guided modes have very small group velocities and very large group velocity dispersions in the region near the f-point and in the region near the Brillouin zone edge. Especially, the group velocity dispersions are found to be millions of times larger than that of a conventional optical fiber. The contributions of the transverse resonance formed by two photonic band gap reflectors and the standing wave mode formed by periodic structures are discussed. We conclude that the highly-dispersive characteristics originate from the resonator-like aspect of the photonic crystal waveguide.

• Structural Engineering and Mechanics
• /
• v.60 no.6
• /
• pp.979-999
• /
• 2016

Stainless steel wire mesh (SSWM) is an alternative material for strengthening of structural elements similar to fiber reinforced polymer (FRP). Finite element (FE) method based Numerical investigation for evaluation of axial strength of SSWM strengthened plain cement concrete (PCC) and reinforced cement concrete (RCC) columns is presented in this paper. PCC columns of 200 mm diameter with height 400 mm, 800 mm and 1200 mm and RCC columns of diameter 200 mm with height of 1200 mm with different number of SSWM wraps are considered for study. The effect of concrete grade, height of column and number of wraps on axial strength is studied using finite element based software ABAQUS. The results of numerical simulation are compared with experimental study and design guidelines specified by ACI 440.2R-08 and CNR-DT 200/2004. As per numerical analysis, an increase in axial capacity of 15.69% to 153.95% and 52.39% to 109.06% is observed for PCC and RCC columns respectively with different number of SSWM wraps.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.93-100
• /
• 2021

Three factors that degrade the accuracy of modal decomposition are extensively studied using simulated and measured beams. These include a beam size mismatch, beam center mismatch, and signal-to-noise ratio of the images. The beam size and beam center are scanned using simulated noisy beams, and the result of the modal decomposition is compared with that of real beams. Based on the suggested procedure, error functions of approximately 1-4 × 10-3 can be acquired for real beams. This study provides important information regarding the impact of the three factors on the practical modal decomposition and tolerances of a mismatch, helping estimate the achievable values of the error function in a real beam modal decomposition.

• Steel and Composite Structures
• /
• v.32 no.2
• /
• pp.173-187
• /
• 2019

This study is concerned with the stability of laminated composite plates modelled using Eringen's nonlocal differential model (ENDM) and a novel refined-hyperbolic-shear-deformable plate theory. The plate is assumed to be lying on the Pasternak elastic foundation and is under the influence of an in-plane magnetic field. The governing equations and boundary conditions are obtained through Hamilton's principle. An analytical approach considering Navier series is used to fine the critical bucking load. After verifying with existing results for the reduced cases, the present model is then used to study buckling of the laminated composite plate. Numerical results demonstrate clearly for the first time the roles of size effects, magnetic field, foundation parameters, moduli ratio, geometry, lay-up numbers and sequences, fiber orientations, and boundary conditions. These results could be useful for designing better composites and can further serve as benchmarks for future studies on the laminated composite plates.

• Computers and Concrete
• /
• v.22 no.6
• /
• pp.501-514
• /
• 2018

The paper presents the thermo-mechanically induced non-linear response of multiwall carbon nanotube reinforced laminated composite beam (MWCNTRCB) supported by elastic foundation using higher order shear deformation theory and von-Karman non-linear kinematics. The elastic properties of MWCNT reinforced composites are evaluated using Halpin-Tsai model by considering MWCNT reinforced polymer matrix as new matrix by dispersing in it and then reinforced with E-glass fiber in an orthotropic manner. The laminated beam is supported by Pasternak elastic foundation with Winkler cubic nonlinearity. A generalized static analysis is formulated using finite element method (FEM) through principle of minimum potential energy approach.

• Steel and Composite Structures
• /
• v.30 no.1
• /
• pp.69-79
• /
• 2019

Numerous problems have always vexed engineers with buckling, corrosion, bending, and over-loading in damaged steel structures. The present study aims to study the possible effects of Carbon Fiber Reinforced Polymer (CFRP) for strengthening deficient Steel Square Hollow Section (SHS) columns. To this end, the effects of axial loading, stiffness values, axial displacement, the shape of deficient on the length of steel SHS columns were evaluated based on a detailed parametric study. Ten specimens were tested to failure under axial compression in laboratory and simulated by using Finite Element (FE) analysis based on numerical approach. The results indicated that the application of CFRP sheets resulted in reducing stress in the damage location and preventing or retarding local deformation around the deficiency location appropriately. In addition, the retrofitting method could increase loading the carrying capacity of specimens.

• Textile Coloration and Finishing
• /
• v.33 no.3
• /
• pp.120-130
• /
• 2021

The condition of covering process using thermoplastic polyetherester elastomeric fibers(TPEE) was established. Two types of core yarn(TPEE, Spandex) and one type of effect yarn(PET) were used as materials to confirm the change in physical properties of covering yarn under various covering conditions. In addition, the effects of the treatment temperature on the elongation at break of covering yarn after heat treatment was analyzed. Through this analysis, it was confirmed that the elastic recovery of TPEE which is used as the core yarn was increased with the draw ratio, but decreases when it exceeds 1:2.5. And the elongation at break of the covering yarn could be increased by increasing the twist per meter of it. Additionally, it was confirmed that the elastic recovery of TPEE which is used as a core yarn, could be increased by applying heat treatment.

• Journal of Korean Society on Water Environment
• /
• v.27 no.3
• /
• pp.329-333
• /
• 2011

p-phenylene-2,5-benzobisoxazole (PBO; Zylon$(R)$) fibers as an adsorbent were employed for solid phase extraction of aqueous alkylphenols. The removal ratios for 10 kinds of alkylphenols at initial concentration of $100{\mu}gL^{-1}$ were in the range of 16.8-96.3% and the removals increased with the increase of the phase ratio (fiber weight/solution volume). The plots of the logarithm of partition coefficient (log K) were correlated with the logarithm of the n-octanol/water partition coefficient (log P). The adsorbed alkylphenols were completely desorbed with the mixture of acetonitrile and dichloromethane.

• Structural Engineering and Mechanics
• /
• v.81 no.4
• /
• pp.513-522
• /
• 2022

Steel-concrete composite segments replacing the conventional reinforced concrete segments can provide the rectangular shield tunnel superiorities on bearing capacity, ductility and economy. A simplified model with high-efficiency on computation is proposed for investigating the nonlinear response of the rectangular tunnel lining composed of composite segments. The simulation model is developed by an assembly of nonlinear fiber beam elements and spring elements to express the transfer mechanism of forces through components of composite segments, and radial joints. The simulation is conducted with the considerations of material nonlinearity and geometric nonlinearity associated with the whole loading process. The validity of the model is evaluated through comparison of the proposed nonlinear simulation with results obtained from the full-scale test of the segmental tunnel lining. Furthermore, a parameter study is conducted by means of the simplified model. The results show that the stiffness of the radial joint at haunch of the ling and the thickness of inner steel plate of segments have remarkable influence on the behaviour of the lining.

• Advances in Computational Design
• /
• v.8 no.1
• /
• pp.61-76
• /
• 2023

Fiber reinforced polymer (FRP) columns are increasingly being used in various engineering fields due to its high strength to weight ratio and corrosion resistance. Being a thin-walled structure, their designs are often governed by buckling.Buckling strength depends on state of stress of elements which is greatly influence by stacking sequence and various inaccuracies such as geometric imperfections and imperfections due to eccentricity of compressive load and non-uniform boundary conditions. In the present work, influence of load eccentricity on buckling strength of FRP column has been investigated by conducting parametric study. Numerical analyses were carried out by using finite element software ABAQUS. The finite element (FE) model was validated using experimental results from the literature, which demonstrated good agreement in terms of failure loads and deformed shapes.The influence of load eccentricity on buckling behavior is discussed with the help of developed graphs.