• Geomechanics and Engineering
• /
• v.37 no.1
• /
• pp.85-95
• /
• 2024

This study investigates the influence of nano-silica and basalt fiber content, curing duration, and freeze-thaw cycles on the static and dynamic properties of soil specimens. A comprehensive series of tests, including Unconfined Compressive Strength (UCS), static triaxial, and dynamic triaxial tests, were conducted. Additionally, scanning electron microscopy (SEM) analysis was employed to examine the microstructure of treated specimens. Results indicate that a combination of 1% fiber and 10% nano-silica yields optimal soil enhancement. The failure patterns of specimens varied significantly depending on the type of additive. Static triaxial tests revealed a notable reduction in the brittleness index (IB) with the inclusion of basalt fibers. Specimens containing 10% nano-silica and 1% fiber exhibited superior shear strength parameters and UCS. The highest cohesion and friction angle were obtained for treated specimens with 10% nano-silica and 1% fiber, 90 kPa and 37.8°, respectively. Furthermore, an increase in curing time led to a significant increase in UCS values for specimens containing nano-silica. Additionally, the addition of fiber resulted in a decrease in IB, while the addition of nano-silica led to an increase in IB. Increasing nano-silica content in stabilized specimens enhanced shear modulus while decreasing the damping ratio. Freeze-thaw cycles were found to decrease the cohesion of treated specimens based on the results of static triaxial tests. Specimens treated with 10% nano-silica and 1% fiber experienced a reduction in shear modulus and an increase in the damping ratio under freeze-thaw conditions. SEM analysis reveals dense microstructure in nano-silica stabilized specimens, enhanced adhesion of soil particles and fibers, and increased roughness on fiber surfaces.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1992.10a
• /
• pp.82-87
• /
• 1992

In this thesis, the fatigue tests were performed on a series of SFRC (steel fiber reinforced concrete)to investigate the flexural tensile behavior of SFRC varying with the steel fiber contents and the steel fiber aspect ratios. Beam specimens of 10$\times$10$\times$60cm are used. the specimen series are classified according to the steel fiber contents varying 0.5. 1.0, 1.5%, and to the steel fiber aspect ratios varying 60, 80, 100. The three point loading system was used in the fatigue tests. The minimum value of repeated loading was fixed at 10.0kgf and maximum value was 75% to static ultimate strength for periodically using concrete strain gages located at the lower end of the mid-span, and the stress-strain curves were drawn for each specimens, respectively. From the tests result, it was found that the larger steel fiber content and the smaller the steel fiber aspect ratio is , the tensile strain of SFRC under fatigue load proportionally increases. By the regression analysis on these results, the empirical formulae to predict the tensile strain of SFRC were suggested. In comparison of the tensile elastic modulus under fatigue load, it was also found that the larger steel fiber content and the smaller steel fiber aspect ratio is , the smaller decreasing rate of the stiffness of SFRC under fatigue load decreased.

• Textile Coloration and Finishing
• /
• v.23 no.1
• /
• pp.51-59
• /
• 2011

Calcium alginate fiber were prepared by wet spinning of various conditions, including different concentrations of sodium alginate solution and $CaCl_2$ concentrations for coagulating the fiber through an absorption of calcium ion. The absorption of calcium ion during the coagulating step lead to solidify the fibers by the replacement of sodium ion with calcium ion to produce some crosslinking. The concentration of calcium ion in the calcium alginate fiber seems to be well related to the mechanical and physical property of the fiber, such as fiber strength moisture regain, and degree of swelling. The tensile strength of calcium alginate fiber was increased along with the increasing amount of sodium alginate solution. According to EDS analysis, 7 wt% $CaCl_2$ coagulation bath resulted in more calcium ion in the fiber compared to 3 wt% $CaCl_2$ coagulation bath. The decomposition temperature of calcium alginate fiber was $199^{\circ}C$, which $14^{\circ}C$ higher than that of sodium alginate.

• Macromolecular Research
• /
• v.14 no.5
• /
• pp.499-503
• /
• 2006

This report presents a new technical approach for evaluating the fiber orientation of composites using small-angle light scattering (SALS). Glass fiber (GF)/polypropylene (PP) composites with different fiber orientations were prepared by drawing compression-molded specimens. The drawn samples were remelted and then annealed at $150^{\circ}C$ in order to induce a crystalline structure on the fiber surface, and then underwent SALS analysis. The samples showed a combination of circular and streak patterns. The model calculations demonstrated that the number of nuclei on the fiber surface and the thickness of the transcrystalline layer affected the sharpness and intensity of the streak pattern. In addition, the azimuthal angle of the streak pattern was found to be dependent on the direction of the transcrystalline layer, which correlated with the fiber direction. This correlation suggests that the fiber orientation in the composites can be easily evaluated using SALS.

• Clinical Nutrition Research
• /
• v.13 no.1
• /
• pp.33-41
• /
• 2024

The health benefits of dietary fiber are widely recognized, but its impact on muscle health remains unclear. Therefore, this study aimed to elucidate the relationship between dietary fiber intake and muscle strength through a cross-sectional analysis of data from the Korea National Health and Examination Survey (KNHANES). Data from a single 24-h dietary recall and handgrip strength tests of 10,883 younger adults aged 19 to 64 years and 3,961 older adults aged ≥ 65 years were analyzed. Low muscle strength was defined as handgrip strength < 28 kg for men and < 18 kg for women. Multivariable linear and logistic regression analyses were conducted to determine the association of dietary fiber intake with muscle strength. Approximately 43% of Korean adults met the recommended intake of dietary fiber, and those with higher dietary fiber consumption also had higher total energy and protein intake. After adjusting for confounding variables, dietary fiber intake was found to be positively associated with maximal handgrip strength in younger women aged 19 to 64 years (β = 0.015; standard error [SE] = 0.006) and older men aged ≥ 65 years (β = 0.035; SE = 0.014). For older women aged ≥ 65 years, those in the lowest quartile of dietary fiber intake had a higher risk of low muscle strength than those in the highest quartile after adjustment of confounders (odds ratio 1.709; 95% confidence interval 1.130-2.585). These results suggest that adequate dietary fiber intake may reduce the risk of sarcopenia in older Korean women.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.891-896
• /
• 2001

As composite materials, the addition of steel fiber in concrete significantly improves the engineering properties of structural members, notably shear strength and ductility, In this study, shear capacity evaluation method according to steel fiber contents was proposed from the literature surveys and member tests. For this, previously proposed five shear strength equation were examined and evaluated by maximum shear strength and shear capacity ratio. From the parametric study and regression analysis, following conclusion can be made; the maximum shear strength of steel fiber reinforced column will be estimated by relative shear capacity ratio.

• ETRI Journal
• /
• v.26 no.4
• /
• pp.371-374
• /
• 2004

We propose and demonstrate a fabrication method of chirped fiber gratings by a thermal diffusion process. The method could suggest a direction for a simple and cost-effective implementation of chirped fiber grating-based devices.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.48-53
• /
• 1997

Volume hologram was recorded using reference beam form optical fiber taper. A singel mode fiber was chemically etced to make a taper structure, and we showed experimentally that the referencing by the irregular beam pattern from this taper structure could increase the storage density of photorefractive volume hologram. The spatial selectivity of the volume hologram with this method was increased by two times compared to the normal single mode fiber referencing case. A theoretical analysis with randomly phased plane model also confirmed the results.

• Composites Research
• /
• v.12 no.5
• /
• pp.23-30
• /
• 1999

Fiber reinforced composite materials are widely used in automotive industry to produce parts that are large, thin, lightweight, strong and stiff. It is very important to know a charge shape in order to have good products in the compression molding. In particular, the product such as a bumper beam is composed of the random and unidirectional fiber mats. The characteristics of flow fronts such as a bulging phenomenon for random mat and unidirectional fiber mat and slip parameters are studied numerically. And the effects of viscosity ratio and stack type on mold filling parameters are also discussed.

• Composites Research
• /
• v.27 no.2
• /
• pp.52-58
• /
• 2014

Short fiber reinforced composites manufactured by injection molding have diverse fiber orientations variable with measuring positions even in the same specimen, which is caused by the flow induced fiber orientation. Fiber orientations considerably affect the mechanical and thermal properties of final composite products. In this study, fiber orientation of injection molded carbon fiber reinforced PA6/PPO composite was measured at several points of the specimen by optical microscopy analysis and the corresponding izod impact strength, coefficients of thermal expansion (CTE) were also measured to investigate the influence of local fiber orientation on the mechanical and thermal properties. Izod impact strength where fiber was perpendicular to the direction of crack propagation was higher than where fiber was parallel to the direction, which could be explained be the impact resistance reinforcing mechanism by fiber orientation. CTE was also lower where fiber was parallel to the measurement direction of CTE than where fiber was perpendicular to the direction, which could be also explained by the dimensional stability mechanism by fiber orientation.