• 한국해양공학회지
• /
• 제13권2호통권32호
• /
• pp.41-50
• /
• 1999

As for the properties on both the aluminum and the CFRP which are used to make A17075/CFRP multi-layered hybrid composites, CRALL(carbon reinforced aluminum laminate). In the CRALL specimen for rule of mixture, we were analyzed notched strength by finite element method. The results obtained from FEM analysis are as follows; In the unnotch CRALL specimen, the stresses CFRP, epoxy, Al 7075 obtained by finite element method strength solution for A/C0001, when strain is 0.28%, are 1400MPa, 38MPa, 411MPa. respectively and for A/C9991, when strain 0.48%, are 392MPa, 26MPa and 321Mpa, respectively. the solpe of the stress-strain curve by FEM increases in keeping with the hole size and the yield strain decrease to 36% and 55% for A/C9993 and A/C9991 respectively.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.483-490
• /
• 2002

This paper presents the results of a comparative study between FEM and LEM on slope stability analysis. For validation, factors of safety were compared between FEM and LEM. The results from the two methods were in good agreement suggesting that the FEM with the shear strength reduction method can be effectively used on slope stability analyses. A series of analysis were then performed using the FEM for various constitutive laws, slope angles, flow rules, and the finite element discretizations. Among the findings, the finite element method in conjunction with the shear strength reduction method can provide reasonable results in terms of factor of safety. Also revealed is that the results of FEM can be significantly affected by the way in which the type of constitutive law and flow rule are selected.

• 전기학회논문지
• /
• 제65권5호
• /
• pp.773-776
• /
• 2016

In the quasi-3D finite element(FE) anlysis, the overall characteristics of axial flux permanent magnet(AFPM) motor could be composed of each computation region. However, A drawback of quasi-3D FEM is not to consider the end effect on the stack end. To address this problem, an improved quasi-3D FE analysis which considers the end effect of the AFPM motor was proposed. From results the 3D FE analysis, the validity of the proposed method is verified.

• 한국생산제조학회지
• /
• 제18권5호
• /
• pp.544-549
• /
• 2009

Thermal brake judder caused by the high friction heat of the brake disk. Hot thermal judder makes serious problems such as to be unstability to drivers or to decrease braking force of automobile. Because thermal judder vibration makes high vibration occurrence and thermal deformation of brake disk. Therefore it Is necessary to reduce or eleminate thermal Judder phenomenon by understanding and investigation. This paper introduces the thermal deformation arising from friction heat generation in braking and proposes the FEM analysis to predict the distribution of temperature and thermal deformation. the results of the FEM analysis show the deformed shape and temperature distribution of the disk brake. The optimization is performed to minimize the thermal judder of ventilated disc brake that is induced by the thermal deformation of the disk brake.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 추계학술대회 논문집
• /
• pp.80-94
• /
• 1994

As for axisymmetirc sheet metal forming, a kind of pick-up apparatus for body-wrinkling is deviced. Experiments with both hemispherical and flat headed punches, with various clearances between punch and die, with respect to three kinds of materials each of which has two thicknesses, are performed. Firstly the process of evolution of body-wrinkling is observed. Then the critical blank-holding force (or meridional tensile force) for suppression of body-wrinkling at a specified punch-stroke is measured for all cases mentioned above. An empirical formula for it is proposed. Deformation patterns and stress distributions are analysed by the use of FEM. A simplified critical condition for body-wrinkling is formulated and introduced into the FEM program. And its effectiveness is checked by comparison with the experimental results. Using this FEM system, the governing factors of body-wrinkling are cleared up.

• Journal of Magnetics
• /
• 제15권3호
• /
• pp.138-142
• /
• 2010

This paper reports the development of an analysis method in a synchronous reluctance motor (SynRM) using the finite element method (FEM) coupled with the electromagnetic field of the Preisach model, which represents an additional thermal source due to hysteresis loss and a thermal field. This study focused on thermal analysis relative to hysteresis and copper losses in a SynRM.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 춘계학술대회 논문집
• /
• pp.171-176
• /
• 2002

There are many railway structures which were designed without conidering aseismic capacity. In special, masonry structures constructed long time ago should be reviewed about their resistance to earthquake. In this paper, technique to evaluate the capacity of masonry railway bridge is tried to develop by means of FEM analysis. In general FEM analysis program, 3-D solid element is used for masonry structures and response spectrum analysis procedure is tried. In addition, 3-D solid element has material properties equivalent to mortar-brick composite body. Used FEM program is ABAQUS-CAE.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.24-30
• /
• 1998

A directly coupled Boundary Element and Finite Element Model was applied to the dynamic analysis of a coupled acoustic silencer with vibratory wall. In this cupled BEM-FEM muffler model, the BEM model was used to discretize the acoustic cavity and the FEM model was used to discretize the vibratory wall structure. Then the BEM model was coupled with the FEM model. The results of the coupled BEM-FEM model for the dynamic analysis of the simple expansion type reactive muffler configurations with flexible walls were verified by comparing the predicted results to analytical solutions. In order to investigate the effects of the muffler's structural flexibility on its transmission loss(TL) characteristics, the results of the coupled BEM-FEM model in conjunction with the four-pole parameter theory were utilized. The muffler's TL characteristics using the BEM-FEM coupled model with flexible walls as compared to other muffler configurations was studied. Finally the muffler's TL values with respect to different wall's thickness are predicted and compared.

• 한국산학기술학회논문지
• /
• 제15권11호
• /
• pp.6458-6463
• /
• 2014

본 논문의 목적은 38인승 승강기 제동장치의 설계 및 유한요소해석이다. 최근 승강기의 안전성이 부각되면서 비상 제동장치의 필요성이 높아졌으며 이에 따라 새로 개발된 제동장치의 안전성을 확인하기 위하여 Solid Works를 활용하여 모델링 하였으며 유한요소해석 코드인 ANSYS를 활용하여 유한요소해석을 수행하였다. 해석결과로서 총변형량, 응력, 변형률을 구하였다.

• 한국안전학회지
• /
• 제26권2호
• /
• pp.1-5
• /
• 2011

In order to evaluate fatigue endurance for an ultra-light weight inline skate frame, FEM analysis was performed. Tensile properties and a S-N curve were determined through tensile and fatigue tests on a modified Al-7075+$S_c$ alloy. The yield and ultimate tensile strengths were 553.3 MPa and 705.5 MPa, respectively. The fatigue endurance limit of this alloy was 201.2 MPa. For evaluating the fatigue endurance of the inline skate frame, the S-N data were compared with the stress analysis results through FEM analysis of the frame. The maximum Von-Mises stress of the frame was determined 106 MPa through FEM analysis of the frame, assuming that the rider weight is 75 Kg. Conclusively, on the basis of fatigue limit, the inline skate frame has a safety factor of approximately 2.0.