• Annual Conference of KIPS
• /
• 2013.11a
• /
• pp.287-289
• /
• 2013

Fast Handover for Proxy Mobile IPv6 (FPMIPv6), a protocol described in RFC 5949, is used to reduce handover latency and minimize packet loss problem occuring in the Proxy Mobile IPv6 (PMIPv6) protocol. However, during the study of implementing FPMIPv6, we found the Out-of-Order Packet (OoOP) problem that occurs in the experiment of FPMIPv6. Since the OoOP is an issue that affects significantly to QoS of the network, in this paper, we analyze the OoOP problem by using network model. The analysis conducts the cause of occurring OoOP problem due to there exist two paths for data transmitted from Correspondent Node (CN) to MN in FPMIPv6.

• Nuclear Engineering and Technology
• /
• v.54 no.6
• /
• pp.2262-2275
• /
• 2022

The Korea Atomic Energy Research Institute (KAERI) studied the sodium-water reaction (SWR) minimized steam generator for the safety of the sodium-cooled fast reactor (SFR), and selected the copper bonded steam generator (CBSG) as the optimal concept. This paper introduces the conceptual design of the CBSG and the development of the CBSG sizing analyzer (CBSGSA). The CBSG consists of multiple heat transfer modules with a crossflow heat transfer configuration where sodium flows horizontally and water flows vertically. The heat transfer modules are stacked along a vertical direction to achieve the targeted large heat transfer capacity. The CBSGSA code was developed for the thermal-hydraulic analysis of the CBSG in a multi-pass crossflow heat transfer configuration. Finally, we conducted a preliminary sizing and rating analysis of the CBSG for the trans-uranium (TRU) core system using the CBSGSA code proposed by KAERI.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.05a
• /
• pp.421-422
• /
• 2021

In this paper, we develop an ultra-sensitive sensor and signal analysis system to measure the load on the wrist. The ultra-sensitive sensor inspired by the organs of a spider is manufactured and the measured signal attached to the wrist is analyzed using FFT (Fast Fourier Transform) and a fuzzy system.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10a
• /
• pp.827-831
• /
• 1987

The analysis of a certian example and simulations given in the previous sections show that the modified FKA is more stable than the standard FKA without loss of the performance of it. The general analysis of modified FKA's numerical stability is the open problem with more simulations in order to prove the stability of it.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.709-710
• /
• 2011

• Korean Journal of Cognitive Science
• /
• v.31 no.1
• /
• pp.1-23
• /
• 2020

This paper introduces SNUDM, an analysis program for Ratcliff's diffusion model, which has been one of the most important models in cognitive psychology over the past 35 years and which has come to occupy an important place in cognitive neuroscience in recent years. The analysis tool is designed with the basic principles of easy comprehension and simplicity in use. A diffusion process was programmed as the limit of a simple random walk in a manner resembling Ratcliff & Tuerlinckx(2002). The response time distribution of the model was constructed by simulating the time taken by a random walk until it reaches a threshold with small steps. The optimal parameter values in the model are found to be the smallest value of the chi-square values obtained by comparing the resulting distribution and the experimental data using Simplex method. For simplicity and ease of use, the input file used here is created as a file containing the quantile of the reaction time, the trials and other information. The number of participants and the number of conditions required for such work programs are given in a way that answers the question. Using this analysis tool, the experimental data of Ratcliff, Gomez, & McKoon(2004) were analyzed. We found the very similar pattern of parameter values to Ratcliff et al.(2004) found. When comparing DMAT, fast-dm and SNUDM with the generated data, we found that when the number of trials is small, SNUDM estimates the boundary parameter to a value similar to fast-dm and less than the DMAT. In addition, when the number of trials was large, it was confirmed that all three tools estimate parameters similarly.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.186-191
• /
• 2004

Sorption kinetics of 2-chlorophenol(2-ChP), 2,4-dichlorophenol(2,4-DChP) and 2,4,5-trichlorophenol (2,4,5-TChP), onto montmorillonite modified with hexadecyltrimethyl ammonium cations(HDTMA-mont) were investigated. One-site mass transfer model(OSMTM) and two compartment first-order kinetic model(TCFOKM) were used to analyze kinetics. As expected from the number of model parameters involved, the three-parameter TCFOKM was better than the two-parameter OSMTM in describing sorption and desorption kinetics of chlorophenols in HDTMA-mont. For all chlorophenols, the results of OSMTM analysis indicate that the predominant deprotonated speciation(at pH 9.15) exhibited higher mass transfer coefficient( $k_{s}$ ) than the protonated speciation(at pH 4.85). This is because the deprotonated speciation has stronger hydrophobic interaction than protonated speciation. Most sorption completes in three hours. The fraction of the fast sorption and the first-order sorption rate constants for the fast and slow compartments in TCFOKM were determined by fitting experimental data to the TCFOKM. The results of kinetics reveal that the fraction of the fast sorption( $f_1$) and the sorption rate constants in the fast compartments( $k_1$) were in the order 2,4,5-TChP > 2,4-DChP > 2-ChP, which agrees with the magnitude of the $K_{ow}$ . The first-order sorption rate constants in the fast compartment(10$^{0.8}$ - 10$^{1.22}$ h $r^{-1}$ ) were much larger than those in the slow compartment(10$^{-1}$.74/ - 10$^{-2}$.622/ h $r^{-1}$ ).> ).).

• Journal of KIISE:Information Networking
• /
• v.34 no.1
• /
• pp.48-61
• /
• 2007

WiBro (Wireless Broadband) service, developed in Korea, can provide the host mobility while its users hang around within the subnet. Next-generation Internet protocols, IPv6 and Mobile IPv6 (MIPv6), provide a plenty of addresses to the nodes and enable the handover between different subnets. However, MIPv6 is not enough to support a real time service such as VoIP (Voice over IP) due to the long latency, and it is necessary to develop an enhanced handover mechanism which is optimized to the WiBro networks. In this paper, we suggest an improved fast handover mechanism while the mobile node moves around WiBro networks. The proposal is based on Fast Mobile IPv6 (FMIPv6) which is the representative protocol for fast handover, and reduces the handover latency by the close interaction between the link layer (WiBro MAC) and IP layer (FMIPv6). Finally, we analyze the performance of proposed mechanism through the mathematical analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.9A
• /
• pp.838-849
• /
• 2005

Fast handover protocol provides seamless handover in mobile Ipv6 networks by reducing handover latency. This paper proposes FMIP-M mechanism to apply this advantage of fast handover protocol to multicast service. The FMIP-M is a fast handover mechanism that supports a reliable multicast service in mobile Ipv6 networks. When hosts move other networks, they may have seine data missing and out-of-synch problems of multicast data. The proposed mechanism provides reliable multicast transmission by compensating data losses from the previous AR. Also it provides an additional function that is able to change multicasting service types dynamically in accordance with network status related with multicasting. So that it is able to make multicast paths very close to the optimum and more efficient multicast service is possible. The performance of the proposed mechanism is evaluated by a time analysis and simulations in various conditions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6C
• /
• pp.637-644
• /
• 2006

This paper presents performance and implementation comparisons of standard and fast DCT algorithms that are commonly used for subband filter bank in MPEG audio coders. The comparison is made according to the architectural difference of the implementation hardware. Fast DCT algorithms are known to have much less computational complexity than the standard method that involves computing a vector dot product of cosine coefficient. But, due to structural irregularity, fast DCT algorithms require extra cycles to generate the addresses for operands and to realign interim data. When algorithms are implemented using DSP processors that provide special operations such as single-cycle MAC (multiply-accumulate), zero-overhead nested loop, the standard algorithm is more advantageous than the fast algorithms. Also, in case of the finite-precision processing, the error performance of the standard method is far superior to that of the fast algorithms. In this paper, truncation errors and algorithmic suitability are analyzed and implementation results are provided to support the analysis.