• Convergence Security Journal
• /
• v.10 no.1
• /
• pp.55-61
• /
• 2010

It is of great practical interest to deciding when to stop testing a software system in development phase and transfer it to the user. This decision problem called an optimal release policies. In this paper, because of the possibility of introducing new faults when correcting or modifying the software, we were researched release comparative policies which based on infinite failure NHPP model and types of interval failure times. The policies which minimize a total average software cost of development and maintenance under the constraint of satisfying a software reliability requirement can optimal software release times. In a numerical example, applied data which were patterns, if intensity function constant or increasing, decreasing, estimated software optimal release time.

• Structural Engineering and Mechanics
• /
• v.39 no.2
• /
• pp.207-221
• /
• 2011

This paper aims to study the behavior of short reinforced concrete columns confined with external glass Fiber Reinforced Polymers (GFRP) sheets under eccentric loads. The experimental part of the study was achieved by testing 9 specimens under eccentric compression. Three eccentricity ratios corresponding to e/t = 0, 0.10, 0.50 in one direction of the column were used. Specimens were divided into three groups. The first group was the control one without confinement. The second group was fully wrapped with GFRP laminates before loading. The third group was wrapped under loading after reaching 75% of failure loads of the control specimens. The third group was investigated in order to represent the practical case of strengthening a loaded column with FRP laminates. All specimens were loaded until failure. The results show that GFRP laminates enhances both failure load and ductility response of eccentrically loaded column. Moreover, the study also illustrates the effect of confinement on the first crack load, lateral deformation, strain in reinforcement and failure pattern. Based on the analysis of the experimental results, a simple model has been proposed to predict the improvement of load carrying capacity under different eccentricity ratios. The predicted equation takes into consideration the eccentricity to cross section depth ratio, the ultimate strength of GFRP, the thickness of wrapping laminate, and the time of wrapping (before loading and under loading). A good correlation was obtained between experimental and analytical results.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.222-227
• /
• 2004

The failure assessment for corroded pipeline has been considered with the full scale burst test and the finite element analysis. The burst tests were conducted on 762 mm diameter, 17.5 mm wall thickness and API 5L X65 pipe that contained specially manufactured rectangular corrosion defect. The failure pressure for corroded pipeline was measured by burst testing and classified with respect to corrosion sizes and corroded regions - the body, the girth weld and the seam weld of pipe. Finite element analysis was carried out to derive failure criteria of corrosion defect on the pipe. A series of finite element analyses were performed to obtain a limit load solution for corrosion defects on the basis of burst test. As a result, the criteria for failure assessment of corrosion defect within the body, the girth weld and the seam weld of API 5L X65 gas pipeline were proposed.

• Structural Engineering and Mechanics
• /
• v.74 no.3
• /
• pp.407-423
• /
• 2020

The pre-peak cyclic shear mechanism of two-order asperity degradation of rock joints in the direct shear tests with static constant normal loads (CNL) are investigated using experimental and numerical methods. The laboratory testing rock specimens contains the idealized and regular two-order triangular-shaped asperities, which represent the specific geometrical conditions of natural and irregular waviness and unevenness of rock joint surfaces, in the pre-peak cyclic shear tests. Three different shear failure patterns of two-order triangular-shaped rock joints can be found in the experiments at constant horizontal shear velocity and various static constant normal loads in the direct and pre-peak cyclic shear tests. The discrete element method is adopted to simulate the pre-peak shear failure behaviors of rock joints with two-order triangular-shaped asperities. The rock joint interfaces are simulated using a modified smooth joint model, where microscopic scale slip surfaces are applied at contacts between discrete particles in the upper and lower rock blocks. Comparing the discrete numerical results with the experimental results, the microscopic bond particle model parameters are calibrated. Effects of cyclic shear loading amplitude, static constant normal loads and initial waviness asperity angles on the pre-peak cyclic shear failure behaviors of triangular-shaped rock joints are also numerically investigated.

• Journal of Applied Reliability
• /
• v.13 no.3
• /
• pp.207-216
• /
• 2013

This paper, we classified LED failure mechanisms that occur due to the delamination and analyzed each of the mechanism that gives the LED PKGs the effect. Usually, the LED is composed of several materials which are LED chips, gold wire, phosphor, epoxy resin, adhesive, reflector and lead frame. These different materials are usually delaminated in trouble conditions which are huge temperature difference, hot and humid or mechanical shocked. When the components are delaminated, a luminance will be lost and moisture be absorbed easily, a thermal resistance be increased attendantly. In this paper, we experimented to investigate failure mechanism of the thermal resistance and failure mechanism of the decrease of luminance that occur due to the delamination. A thermal shock test was performed to reproduce this phenomena by subjecting samples to a cold-hot cyclling process between $-30^{\circ}C$(15min) and $110^{\circ}C$(15min). The samples were inspected at 200, 600 and 1,000 cycles. We measured feature of LED using the spatial analyzer, optical microscope, thermal resistance, photometer, scanning electron microscope (SEM). As a result, the progression of the crack and the thermal resistance and decrease in luminance are proportional to number of thermal shock.

• Journal of Drive and Control
• /
• v.15 no.4
• /
• pp.48-54
• /
• 2018

The hydraulic servo actuator has always operated very precisely with high frequency and small displacement, and is used continuously for a long time. The hydraulic servo actuator of the test equipment used in the accelerated life test in order to guarantee the service life of the automotive parts failed earlier than the products before finishing the test. This study performed an analysis on the cause of the failure of the hydraulic servo actuator used in the test equipment, changed the design of the actuator to solve the root cause of the main failure mode, and developed the improved servo actuator. Based on above process, this study established a better performances and longer lifetime of the servo actuator after testing.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.463-478
• /
• 2021

The subjects of the study are the sedimentary rock slope of the Mesozoic Gyeongsang Supergroup, which has a high risk of failure. The orientation of the slope-face represents a variety of changing characteristics. The rocks of the slope shall be sandstone, siltstone and dacite, and discontinuities shall develop beddings, shear joints, extension joints, and dacite dyke boundary planes. The type and scale of failure varies depending on the type of rock and the strike/dip of the discontinuities, but the toppling failure prevails. Based on the face-mapping data, SMR, physical and mechanical testing of rocks, analysis and review of the stereonet projections and the critical equilibrium analysis, all four representative sections required a countermeasure method because the acceptable safety factor during dry and rainy seasons were far below Fs = 1.5 and Fs = 1.2. After applying the countermeasure method, both the dry and wet conditions of the slope exceeded the allowable safety factor. In particular, the face-mapping data of the slope-face, the geological cross-sections of several representative sections perpendicular to the slope-face, and the critical equilibrium analysis and the presentation of countermeasure methods that have been reviewed based on them are expected to be reasonable tools for the slope stability. In addition, it will be possible to use it as basic data for performance evaluation for slope maintenance.

• Corrosion Science and Technology
• /
• v.22 no.3
• /
• pp.153-163
• /
• 2023

Two types of accelerated tests, Water Drop Test (WDT) and Temperature-Humidity-Bias Test (THBT), can be used to evaluate the susceptibility to electrochemical migration (ECM). In the WDT, liquid water is directly applied to a specimen, typically a patterned conductor like a printed circuit board. Time to failure in the WDT typically ranges from several seconds to several minutes. On the other hand, the THBT is conducted under elevated temperature and humidity conditions, allowing for assessment of design and life cycle factors on ECM. THBT is widely recognized as a more suitable method for reliability testing than WDT. In both test methods, localized corrosion can be observed on the anode. Composition of dendrites formed during the WDT is similar to that formed during THBT. However, there is a lack of correlation between the time to failure obtained from WDT and that obtained from THBT. In this study, we investigated the relationship between electrochemical parameters and time to failure obtained from both WDT and THBT. Differences in time to failure can be attributed to actual anode potential obtained in the two tests.

• Computers and Concrete
• /
• v.34 no.1
• /
• pp.15-31
• /
• 2024

This study explores the failure mechanisms of 'I' shaped non-persistent cracks under uniaxial loads through a combination of experimental tests and numerical simulations. Concrete specimens measuring 200 mm×200 mm×50 mm were manufactured, featuring 'I' shaped non-persistent joints. The number of these joints varied from one to three, with angles set at 0, 30, 60, and 90 degrees. Twelve configurations, differing in the placement of pre-existing joints, were considered, where larger joints measured 80 mm in length and smaller cracks persisted for 20 mm with a 1 mm crack opening. Numerical models were developed for the 12 specimens, and loading in Y-axis direction was 0.05 mm/min, considering a concrete tensile strength of 5 MPa. Results reveal that crack starting was primarily influenced by the slope of joint that lacks persistence in relation to the loading direction and the number of joints. The compressive strength of the samples exhibited variations based on joint layout and failure mode. The study reveals a correlation between the failure behavior of joints and the number of induced tensile fracture, which increased with higher joint angles. Specimen strength increased with decreasing joint angles and numbers. The strength and failure processes exhibited similarities in both laboratory testing and numerical modeling methods.

• Journal of KIISE
• /
• v.42 no.12
• /
• pp.1551-1560
• /
• 2015

Software Reliability Growth Models (SRGMs) are used to quantitatively evaluate software reliability and to determine the software release date or additional testing efforts using software failure data. Because a single SRGM is not universally applicable to all kinds of software, the selection of an optimal SRGM suitable to a specific case has been an important issue. The existing methods for SRGM selection assess the goodness-of-fit of the SRGM in terms of the collected failure data but do not consider the accuracy of future failure predictions. In this paper, we propose a method for selecting SRGMs using the trend of failure data and failure prediction ability. To justify our approach, we identify problems associated with the existing SRGM selection methods through experiments and show that our method for selecting SRGMs is superior to the existing methods with respect to the accuracy of future failure prediction.