• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.6
• /
• pp.709-719
• /
• 2023

In general, most of the electrical equipment responsible for control within power plants is housed in self-standing cabinets. These cabinets are typically fixed to a slab using post-installed anchors. Although the fixation method of using post-installed anchors provides stability, there is a risk of conductor failure due to external forces, including moments. However, the performance assessment of current anchors is only evaluated through uniaxial material tests. Therefore, the primary purpose of this study is to compare the static performance of post-installed anchors, considering on-site installation conditions, with their performance in material tests and to analyze the behavioral characteristics of the anchors. While conducting experiments using actual cabinets would be ideal, practical and spatial constraints make this approach difficult. As an alternative, experiments were conducted using a test specimen consisting of a steel column and a support. As a result, the pull-out performance of anchors reflecting on-site installation conditions was measured to be about 10% higher than that observed in material tests. The trends in load reduction and the point of maximum performance for the anchors also differed. To verify the reliability of the experimental study, a 3D FEM analysis was performed, which will provide predictive information on the loads transferred to the post-installed anchors for structural performance evaluations of electrical cabinets using shaking table test in the future.

• Composites Research
• /
• v.36 no.6
• /
• pp.441-447
• /
• 2023

Recently, as demand for high-strength, lightweight materials has increased, there has been great interest in joining with metals. In the case of mechanical bonding, such as bolting and riveting, chemical bonding using adhesives is attracting attention as stress concentration, cracks, and peeling occur. In this paper, surface treatment was performed to improve the adhesive strength, and the change in adhesive strength was analyzed. For the adhesive strength test were conducted with Carbon Fiber Reinforced Plastic(CFRP), CR340(Steel), and Al6061(Aluminum), and laser and plasma surface treatment were used. After plasma surface treatment, the adhesive strength improved by 7.3% and 39.2% in CFRP-CR340 and CFRP-Al6061, respectively. CR340-Al6061 was improved by 56.2% in laser surface treatment. Surface free energy(SFE) was measured by contact angle after plasma treatment, and it is thought that the adhesion strength was improved by minimizing damage through a chemical reaction mechanism. For laser surface treatment, it is thought that creates a rough bonding surface and improves adhesive strength due to the mechanical interlocking effect. Therefore, surface treatment is effect to improve adhesive strength, and based on this paper, the long-term fatigue test will be conducted to prevent fatigue failure, which is a representative cause of actual structural damage.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.3
• /
• pp.538-553
• /
• 1999

The purpose of this study was to compare the shear bond strength and the anticariogenicity of glass ionomer cement with conventional bonding resin and fluoride releasing resin. After the shear bond strength test, scanning electron microscopic observation was performed for the evaluation of the fracture patterns in each group. Under the polarizing light microscope, artificially induced carious lesions were evaluated and the lesion depths of the samples were measured using image analyzing program(Image-Pro $PLUS^{TM}$, USA). 50 sound maxillary premolars were used for the bond strength test and another 30 for the anticariogenic test. Data collected were analyzed statistically using Oneway-ANOVA and Scheffe test. The results were as follows: 1. Glass ionomer groups(G-III, IV, V) generally showed the lower bond strength values than resin groups(G-I, II). 2. Among the two resin groups, G-I showed the higher bond strength than G-II without statistically significant difference between them(p>.05). 3. Within glass ionomer groups, statistical significance was found between G-III and G-V with the superior bond strength in G-V (p<.05). 4. Under the SEM, adhesive failure was the predominant fracture pattern in G-I and II, whereas cohesive failures were mainly observed in G-III. In G-IV and V, mixed type of pattern where the both fracture patterns coexisted within samples could be seen. 5. In evaluation of the depth of artificially developed carious lesion, glass ionomer group showed shallower depth than resin groups with statistical significance between G-III and G-I, II(p<.05). Among resin groups, fluoride releasing resin(G-II) showed the shallower depth than conventional resin(G-I)(p<.05).

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.4
• /
• pp.332-340
• /
• 2016

Sunken ships cause damage to the environment due to the dispersal of fuel oil and harmful cargo goods in the hull. Since the sunken ship is mostly flooded by the seabed, it tends to be in a relatively stable condition. However, the heavy body, together with the load of remaining goods in the cargo hold, the constant contact with the seabed, and ocean currents and tidal waves, can affect dispersal of residual fuel oils out of the sunken ship. Corrosion of the sunken ship starts upon sinking, decreasing the thickness of the hull structure and sub-materials. Therefore, it is necessary to assess the structural stability against the potential breakdown of the sunken ship. Whilst evaluating the danger of the sunken ship, this result should be reflected in 'the possible discharge'. This study was undertaken to suggest a procedure for a step by step evaluation to assess the structural stability a sunken ship. The structural stability assessment to estimate the collapsibility of the hull was structure targeted at the sunken ship 'No. 7 HaeSung', which was classified as the prime example for the intensive management of sunken ships. This study was undertaken to suggest a procedure for a step by step evaluation to assess the structural stability a sunken ship and to propose a method to conduct a structural safety assessment that estimates the collapsibility of the hull by targeting the sunken ship 'No. 7 HaeSung',which was classified as the prime example for the intensive management of sunken ships. The collapsibility of the hull structure was estimated Based on the damage size of the hull structure, and the corrosion rate of the hull structure and sub-materials due to the seawater after sinking. It was confirmed that there was a low possibility of the total destruction of the hull structure at the current time. However, there is a high possibility in the potential failure of the hull structure due to increased rate of corrosion thereafter. Therefore, we believe continuous study on influence of corrosion and marine environment change to sunken ship's structural safety is necessary.

• Journal of Oral Medicine and Pain
• /
• v.36 no.4
• /
• pp.225-234
• /
• 2011

Tobacco smoking is a major risk factor of systemic health and also impairs oral health, which is related to development of oral cancers, periodontitis, delayed wound healing, tooth loss, failure of implant, etc. Aside from smoking, many other risk factors can be related to oral health and long-term effects of smoking on salivary flow and taste threshold are still in controversy. Authors considered dental students to be an appropriate group with good oral hygiene for a long-term study to reveal effects of smoking on oral health. This study was performed to compare smoking patterns and current oral health conditions between smokers and nonsmokers in dental students prior to long-term evaluation. 192 volunteers (85.7%) of 224 male dental students in Dankook University were evaluated through questionnaires and clinical examination in 2010. Questionnaires included smoking pattern, alcohol use, nicotine dependence, preventive care, psychological profile and clinical examinations comprised assessment of teeth or periodontal status, nicotine pigmentation, salivary flow, electrical taste thresholds and halitosis. From the study, (current) smokers were older, and drank more frequently with more alcohol intake compared to former smokers and nonsmokers(p<0.05). There was no significant difference among them in salivary flow rate, halitosis and electrical taste threshold. However, there was significant difference in DMFT rate, periodontal treatment need, nicotinic pigmentation between smokers and nonsmokers(p<0.05), irrespective of their levels of preventive care. The smokers in this study, who are young dental students with relatively shorter duration of smoking, less use of cigarettes and low level of nicotine dependence, did not reveal significant impairment of oral health. However, their oral health was found to be relatively impaired compared to nonsmokers', which suggests negative effect of smoking on the oral health and a need of smoking cessation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.12 no.1
• /
• pp.15-23
• /
• 1979

In the first paper of the series the five soil fertility factors were evaluated by means of principal component analysis and varimax method. They are interpreted as representing, 1) skeletal available phosporus status, 2) organnic matter status, 3) salt status 4) base status, and 5) free oxide status. In order to resynthesize such fragmented information for the overall soil fertility evaluation, the method of multiple regression analysis was adopted, using the five factor scores and yield data for Korean paddy soils as independent and dependent variables respectively. As test of linear models with different combinations of independent variables the results of t-test of regression coefficient were revealed that the organic matter status (FII) has no relevance to the yield of paddy and that the free oxides and salt supply has by it self only an insignificant contribution to the yield. The multiple correlation coefficient (R) revealed its multiple regression analysis was as low as 0.43. Introduction of quadratic terms to the linear model bettered the result. Thus multiple correlation coefficient (R) was increased as 0.59. Therefore, a coefficient of determination 0.35 was obtained by a quadratic model with interaction terms among the five fertility constituents. Generally we think that the fertility factor has more contribution to raise the rice yield in paddy and that the failure of yield prediction by fertility factor scores was caused by one of follows; 1) the roughness of the yield inspection, and 2) missextraction of fertility constituents. The second step in this study, assuming that the residuals by multiple regression analysis were due to factors other than soil fertility, we can now proceed to predicting the yield from the field characters with the classified fertility groups by means of Hayashi's theory of quantification No. 1. Such variables as fertility groups (FTYG), water availability (WATER), soil drainage (DRNG), climatic zone (CLIZ), surface soil's stickiness (STCKT), surface soil's dry consistence (DCNST), and surface soil's texture (FTEXT) are taken up as the explanatory variables. The quantification appears reasonable; the well to extremely well in soil drainage, very sticky of surface soil, inefficiency in water availability, coarse texture, and very hard to extremely hard dry consistence in soil are detrimental to the rice yield. The R was as high as 0.90 for the set of variables. But the given explanatory variables in this study were not quite effective in explaining rice yield. The method developed seems to be promising only if properly collected data are available. Conditions that should be satisfied in the yield inspection obtained from common cultivator for the purpose of deriving a prediction equation were put forward.

• Radiation Oncology Journal
• /
• v.28 no.2
• /
• pp.85-90
• /
• 2010

Purpose: To evaluate the rate of tumor response, local control, and treatment-related complications after hypofractionated radiotherapy for recurrent hepatocelluar carcinoma (HCC) less than 5 cm in size. Materials and Methods: Among the HCC patients who were treated by radiotherapy (RT) between 2006 and 2007 after the failure of previous treatment, a total of 12 patients were treated with hypofractionated RT. The criteria for hypofractionated RT was as follows: 1) HCC less than 5 cm, 2) HCC not adjacent to a critical organ, 3) HCC without portal vein tumor thrombosis, and 4) less than 15% of normal liver volume that irradiated 50% of the prescribed dose. Hypofractionated RT was performed with 50 Gy delivered in 10 fractions, at a rate of 5 fractions per week. The evaluation of tumor response was determined by CT scans performed at 3 months after the cessation of RT, followed by the evaluation of toxicity by Common Terminology Criteria for Adverse Events version 3.0. The median follow-up period after radiotherapy was 18 months. Results: A complete response (CR) was achieved in 5 of 12 lesions (41.7%) at CT performed at 3 months after the cessation, whereas the overall complete response was observed in 7 of 12 cases (58.3%). In-field local control rate was sustained in 83.3% of patients. All patients developed intra-hepatic metastases except for 2 patients. The overall survival rate was 90.0% at 1 year and 67.5% at 2 years, respectively. Three patients developed Grade 1 nausea during RT and 1 patient showed a progression of ascites after RT. There was no grade 3 or greater treatment-related toxicities. Conclusion: Hypofractionated RT for small-sized HCC as a salvage therapy showed a 58.3% CR rate and 83.3% of local control. Fifty Gy administered in 10 fractions of partial liver irradiation is considered as a tolerable dose that does not cause severe complications.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.1
• /
• pp.73-80
• /
• 2022

In this study, details of NRC beam-column connections were developed in which beam and columns pre-assembled in factories using steel angles were bolted on site. The developed joint details are NRC-J type and NRC-JD type. NRC-J type is a method of tensile joining with TS bolts to the side and lower surfaces of the side plate of the NRC column and the end plate of the NRC beam. NRC-JD type has a rigid joint with high-strength bolts between the NRC beam and the side of the NRC column for shear, and with lap splices of reinforcing bar penetrating the joint and the beam main reinforcement for bending. For the seismic performance evaluation of the joint, three specimens were tested: an NRC-J specimen and NRC-JD specimen with NRC beam-column joint details, and an RC-J specimen with RC beam-column joint detail. As a result of the repeated lateral load test, the final failure mode of all specimens was the bending fracture of the beam at the beam-column interface. Compared to the RC-J specimen, the maximum strength of the specimen by the positive force was 10.1% and 29.6% higher in the NRC-J specimen and the NRC-JD specimen, respectively. Both NRC joint details were evaluated to secure ductility of 0.03 rad or more, the minimum total inter-story displacement angle required for the composite intermediate moment frame according to the KDS standard (KDS 41 31 00). At the slope by relative storey displacemet of 5.7%, the NRC-J specimen and the NRC-JD specimen had about 34.8% and 61.1% greater cumulative energy dissipation capacity than the RC specimen. The experimental strength of the NRC beam-column connection was evaluated to be 30% to 53% greater than the theoretical strength according to the KDS standard formula, and the standard formula evaluated the joint performance as a safety side.

• Journal of the Korean Society of Earth Science Education
• /
• v.15 no.3
• /
• pp.335-344
• /
• 2022

This study was conducted for 4 weeks on the preparation of the science teaching/learning course plan for 109 students in 4 classes of the 2nd year intensive course at B University of Education. Pre-service elementary teachers attended a two-week field training practice after listening to a lecture on how to write a science teaching and learning course plan. Pre-service elementary teachers tried to find out about the selection of materials and the degree of connection between the course plan and the class to prepare the science teaching/learning course plan. The researcher completed the questionnaire by reviewing and deliberation on the questionnaire questions together with 4 pre-service elementary teachers. The questionnaire related to the writing of the science teaching and learning course plan consists of 8 questions. Preferred reference materials when writing the course plan, the level of interest in learning, the success or failure of the science course plan and class, the science preferred model, the evaluation method in unit time, and the science teaching and learning One's own efforts to write the course plan, the contents of this course are the science faculty. It is composed of the preparation of the learning process plan and how helpful it is to the class. The results of this study are as follows. First, it was found that elementary school pre-service elementary teachers preferred teacher guidance the most when drafting science teaching and learning curriculum plans. Second, it is recognized that the development stage is very important in the teaching and learning stage of the science department. Third, Pre-service elementary teachers believe that the science and teaching and learning process plan has a high correlation with the success of the class. Fourth, it was said that the student's level, the teacher's ability, and the appropriate lesson plan had the most influence on the class. Fifth, it was found that pre-service elementary teachers prefer the inquiry learning class model. Sixth, it was found that reports and activity papers were preferred for evaluation in 40-minute classes. Seventh, it was stated that the teaching and learning process plan is highly related to the class, so it will be studied and studied diligently. Eighth, the method of writing a science teaching and learning course plan based on the instructional design principle is interpreted as very beneficial.

• Journal of the Korean Orthopaedic Association
• /
• v.52 no.1
• /
• pp.1-6
• /
• 2017

Purpose: To retrospectively compare minimally invasive percutaneous plate osteosynthesis (MIPPO) with open plate fixation for the treatment of clavicle midshaft fracture. Materials and Methods: Between November 2011 to May 2014, 40 cases that were followed for more than 1 year-among all cases of MIPPO and open plate fixation-were analyzed. The study population was divided into two groups: group A included 20 cases of MIPPO and group B included 20 open plate fixation cases. The comparative analysis between the two groups was based on the operative time, bone union, functional evaluation (American Shoulder and Elbow Society score), incision length, pain relief (visual analogue scale, VAS), and complication. Results: The bone union was successful for all the cases, and the functional evaluation scores of the shoulder joint were satisfactory for both groups (p>0.05). The operative time was 47.5 minutes and 58.7 minutes for group A and B, respectively (p<0.05). The incision length for group A was 6.2 cm and that for group B was 10.7 cm with statistical significance (p<0.05). Pain relief (VAS) after surgery for group A showed a quick recuperation in the early stages. For complications, there were 2 cases of dysesthesia and 1 case of malunion due to metal fixation failure in group A. There were 6 cases of dysesthesia and 2 cases of cosmetic problem due to hypertrophic scar in group B. Conclusion: Surgical results of clavicle shaft fracture were satisfactory for both groups, but group A had advantages of shorter operative time, minimal incision length, and better pain relief in the early stages compared with group B. However, we need further evaluations with long-term follow-up results and complications, such as malunion and exposure on radiation.