• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.77-88
• /
• 2000

In this paper, the 3-mode variable gain high power amplifier for a transmitter of INMARSAT-B operating at L-band(1626.5-1646.5 MHz) was developed. This SSPA can amplify 42 dBm in high power mode, 38 dBm in medium power mode and 36 dBm in low power mode for INMARSAT-B. The allowable errol sets +1 dBm as the upper limit and -2 dBm as the lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier. The HP's MGA-64135 and Motorola's MRF-6401 were used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 for the high power amplifier. The SSPA was fabricated by the RP circuits, the temperature compensation circuits and 3-mode variable gain control circuits and 20 dB parallel coupled-line directional coupler in aluminum housing. In addition, the gain control method was proposed by digital attenuator for 3-mode amplifier. Then il has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. In this case, the SSPA detects the output power by 20 dB parallel coupled-line directional coupler and phase non-splitter amplifier. The realized SSPA has 41.6 dB, 37.6 dB and 33.2 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.3:1. The minimum value of the 1 dB compression point gets more than 12 dBm for 3-mode variable gain high power amplifier. A typical two tone intermodulation point has 36.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.208-221
• /
• 2007

The fracture toughness test is believed as a clinically relevant method for assessing the fracture resistance of the dentinal restoratives. The objectives of this study were to measure the fracture toughness $(K_{1C})$ and microtensile bond strength of dentin-resin composite interface and compare their relationship for their use in evaluation of the integrity of the dentin-resin bond. A minimum of six short-rod specimens for fracture toughness test and fifteen specimens for microtensile bond strength test was fabricated for each group of materials used. After all specimens storing for 24 hours in distilled water at $37^{\circ}C$, they were tensile-loaded with an EZ tester universal testing machin. Statistical analysis was performed using ANOVA and Tukey's test at the 95% confidence level, Pearson's coefficient was used to verify the correlation between the mean of fracture toughness and microtensile bond strength. FE-SEM was employed on fractured surface to describe the crack propagation. Fracture toughness value of Clearfil SE Bond (SE) was the highest, followed by Adper Single Bond 2 (SB), OptiBond Solo (OB), ONE-STEP PLUS (0S), ScotchBond Multi-purpose (SM) and there was significant difference between SE and other 4 groups (p < 0.05). There were, however, no significant difference among SB, OB, OS, SM (p > 0.05). Microtensile bond strength of SE was the highest, followed by SB, OB, SM, OS and OS only showed significant lower value (p < 0.05). There was no correlation between fracture toughness and microtensile bond strength values. FE-SEM examination revealed that dentin bonding agent showed different film thickness and different failure pattern according to the film thickness. From the limited results of this study, it was noted that there was statistically no correlation between K1C and ${\mu}TBS$. We can conclude that for obtaining the reliability of bond strength test of dentin bonding agent, we must pay more attention to the test procedure and its profound scrutiny.

• Journal of the Korean Geographical Society
• /
• v.29 no.2
• /
• pp.137-165
• /
• 1994

Structural adjustment of industry (or industrial restructuring) seems to be inherent in the process of capitalist economic development, which tends to be proceeded with shifts from one stage to another in order to overcome structural crises generated in each stage. The structural adjustment of industry is necessarily accompanied with regional restructuring, since it is not only projected on spece, but also mediated by space. Such a restructuring necessitates industrial and uneven regional devlopment through which capital can seek excessive profits over the rate of socio-spatial average. The industrial restructuring and uneven regional development in the 1980s in Korea can be seen as a process in which capital attempted with a strong support of the govenment to overcome the crises in the end of 1970s and hence to go on rapid economic growth. In this process, capital, especially monopoly capital concentrated into few conglomerates, pursued both extensive expansion and intensive development of industry simultaneously. In results, the Korean economy could eliminate some of peripheral characters and maturate the Fordist accumulation system. The extensive expansion of the Korean industry in the 1980s was stimulated mainly through the enlargement and adjustment of investment for equipment facilities which was planned to exclude or rationalize traditional light industries on some places, and to continue rapid growth of key heavy-chemical industries, especially of fabricated metal industry, on other places. In this process, keeping mainly the existing developmental axis which polarized the Seoul Metroplitan region and the Southeast region in Korea, the enhancing spatial mobiiity of capital and the further differentiating division of labour enforced a tendency of concentration of all types of industry in the Seoul Metropolitan region, and at the same time provoked the diffusion of some industries over Jeolla and Chungchong regions in a considerable extent. The intensive development of industriai structure in the 1980s was pursued through the strategic encouragement of subcontracting small firms mainly which produced assembling components, the technical enhancement and factory (semi-) automation, and the enrichment of service industries for estate management, finance, distribution and retailing which supported and complemented the production of goods. In this process, enabling capital to extend and elaborate its domination over space through the reorganization of regulating systems, the Fordist division of labour generated a socio-spatial hierarchy in the nation-wide scale that characterized: the Seoul Metropolitan region as an overmaturated (or overarching) Fordist region performing the conceptive functions of management, research and development, in which all types of industry (including service industries) tended to be reconcentrated; Kyungsang region as a maturated Fordist region with excutive branches of large conglomerates and with subcontracting firms around them which produced standardized products through the automized production processes in secialized Fordist industries or rationalized traditional industries; and Jeolla and Chungchong regions as newly devloping Fordist regions with newly migrated branches and some subcontracting small firms-in relatively older Fordist industries or partly rationalized traditional industries. From these analyses, it can be argued that the structural adjustment of the Korean industry in the 1980s, which had carried out both through the extensive expansion and the intensive deveiopment, strengthened further uneven regional development process, even though it appears to have reduced apparently the economic and regional disparity by balancing numerically large and small firms and by extending the Fordist industrial space nation-wideiy. And it seems more persuasive to see that the Korean industrial structure in the 1980s maturated the Fordist system of accumulation, but not yet transformed towards the post-Fordist (or the so-called flexible) accumulation system, even though the Korean economy in the 1990s seems to be under a pressure of restructuring towards the latter system.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.101-108
• /
• 1993

$TiO_{2}$/Se : Te heterojunction for color sensor has been fabricated by RF reactive sputtering and thermal evaporation methods onto glass substrate. The optimum deposition condition of $TiO_{2}$ films was such that RF power was 120 W, substrate temperature was $100^{\circ}C$, oxygen concentration was 50%, working pressure was 50 mTorr for the $TiO_{2}$ film thickness of $1000{\AA}$. In this case, the optical transmittance of $TiO_{2}$ film at 550 nm-wavelength was 85%, resistivity was $2{\times}10^9{\Omega}{\cdot}cm$, refractive index was 2.3, and optical bandgap was 3.58 eV. The composition ratio of 0 to Ti by AES analysis was 1.7. When $TiO_{2}$ films were annealed at $400^{\circ}C$ for 30 min. in $O_{2}$ ambient, the optical transmittance of $TiO_{2}$ films at the wavelength range of $300{\sim}580$ nm was improved from 0 to 25%. When Se : Te films were annealed at $190^{\circ}C$ for 1 min., photosensitivity under illumination of 1000 lux was 0.75. The optical bandgap of Se : Te films was 1.7 eV. The structures of Se : Te films were the hexagonal with (100) and (110) orientation. The spectral response of a-Se was improved by the addition of Te, especially in the long wavelength region. The $TiO_{2}$/Se : Te heterojunction showed wide spectral response, and more improved one than that of a-Si film in the blue light region.

• Analytical Science and Technology
• /
• v.11 no.1
• /
• pp.62-72
• /
• 1998

This study was performed to characterize the trace organic pollutants in the industrial wastewater and to establish the database of the trace organic pollutants. The four manufacturing industries, which are refined petroleum, industrial chemicals, rubber & plastics and fabricated metals, were surveyed. The wastewater and discharging water of these 30 factories are analyzed to characterize the trace organic pollutants. In industrial chemicals, the kinds of products and organic pollutants are very various. Therefore to select the characteristic organic pollutants in this categories are also very difficult. In industrial chemicals, the gas chromatograpic peak patterns of wastewater are represented the various type according to their products, therefore the typical patterns of the characteristic organic pollutants could not be obtained because the kinds of manufactured goods and organic pollutants are very various. In refined petroleum, the effluent is discharged in the distillatory process of atmosphere pressure and contained the saturated hydrocarbons, phenol compounds, benzene compounds and naphtalene compounds. The saturated hydrocarbons peaks from $C_{15}$ to $C_{35}$ are represented the typical oil patterns by the uniform intervals therefore the peak can be easily distinguished. In rubber & plastics, the wastewater is discharged in the washing process which contains the additives. The problem of wastewater is not serious because the manufacturing process is not produced the effluent or the produced cooling water is recycled in that process.

• Restorative Dentistry and Endodontics
• /
• v.34 no.3
• /
• pp.177-183
• /
• 2009

The aim of this study was to evaluate the marginal and internal gaps in CEREC3 CAD/CAM inlays of three different preparation designs. CEREC3 Inlays of three different preparation designs (n=10) were fabricated according to Group I-conventional functional cusp capping/shoulder preparation, Group II-horizontal reduction of cusps and Group III-complete reduction of cusps/shoulder preparation. After cementation of inlays. the bucco-lingual cross section was performed through the center of tooth. Cross section images of 20 magnifications were obtained through the stereomicroscope. The gaps were measured using the Leica application suite software at each reference point. Statistical analysis was performed using one-way ANOVA and Tukey's test (${\alpha}<0.05$). The marginal gaps ranged from 80.0 to $97.8{\mu}m$ for Group I, 42.0 to $194.8{\mu}m$ for Group II, 51.0 to $80.2{\mu}m$ for Group III. The internal gaps ranged from 90.5 to $304.1{\mu}m$ for Group I, 80.0 to $274.8{\mu}m$ for Group II, 79.7 to $296.7{\mu}m$ for Group III. The gaps of each group were the smallest on the margin and the largest on the horizontal wall. For the CEREC3 CAD/CAM inlays, the simplified designs (groups II and III) did not demonstrate superior results compared to the traditional cusp capping design (group I).

• Restorative Dentistry and Endodontics
• /
• v.32 no.4
• /
• pp.343-355
• /
• 2007

The objectives of this study was to evaluate the durability of 4 resin cements by means of microtensile bond strength test combined with thermocycling method and fractographic FE-SEM analysis. Experimental groups were prepared according to thermocycling (0, 1,000, 5,000) and the kind of resin cements, those were Variolink II, Multilink, Panavia F 2.0, Rely X Unicem. Flat dentin surfaces were created on mid-coronal dentin of extracted third molars. Then fresh dentin surface was grounded with 320-grit silicon carbide abrasive papers to create uniform smear layers. Indirect composite block (Tescera, Bisco Inc., Schaumburg, IL, USA) was fabricated ($12\;{\times}\;12\;{\times}\;6\;mm^3$). It's surface for bonding to tooth was grounded with silicon carbide abrasive papers from 180- to 600-grit serially, then sandblasted witk $20\;-\;50\;{\mu}m$ alumina oxide. According to each manufacturer's instruction, dentin surface was treated and indirect composite block was luted on it using each resin cement. For Rely X Unicem, dentin surface was not treated. The bonded tooth-resin block were stored in distilled water at $37^{\circ}C$ for 24 hours. After thermocycling, the bonded tooth-resin block was sectioned occluso-gingivally to 1.0 mm thick serial slabs using all Isomet slow-speed saw (Isomet, Buehler Ltd, Lake Bluff, IL, USA). These sectioned slabs were further sectioned to $1.0\;{\times}\;1.0\;mm^2$ composite-dentin beams. The specimens were tested with universal testing machine (EZ-Test, Shimadzu, Japan) at a crosshead speed of 1.0 mm/min with maximum load of 500 N. The data was analyzed using one-way ANOVA and Duncan's multiple comparison test at $p\;{\leq}\;0.05$ level. Within the limited results, we conclude as follows; 1. The bond strength of Variolink II was evaluated the highest among experimental groups and was significantly decreased after 1,000 thermocycling (p < 0.05). 2. The bond strength of Multilink was more affected by thermocycling than the other experimental groups and significantly decreased after 1,000 thermocycling (p < 0.05). 3. Panavia F 2.0 and Rely X Unicem showed the gradually decreased tendency of microtensile bond strength according to thermocycling but there was no significant difference (p > 0.05). 4. Adhesive based-resin cements showed lower bond strength with or without thermocycling than composite based-resin cements. 5. Variolink II & Multilink showed high bond strength and mixed failure, which was occurred with a thin layer of luting resin cement before thermocycling and gradually increased adhesive failure along the dentin surface after thermocycling. The bonding performance of resin cement can be affected by application procedure and chemical composition. Composite based-resin cement showed higher bond strength and durability than adhesive based-resin cement.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.4
• /
• pp.417-428
• /
• 2011

Depending on the plastic deformation capacity required, structural steel design under the current codes can be classified into three categories: elastic, plastic, and seismic design. Most of the current steel codes explicitly forbid the use of a steel material with a yield strength higher than 450 MPa in the plastic design because of the concerns about its low plastic deformation capacity as well as the lack of test data on local and lateral torsional buckling behavior. In this study, flexural tests on full-scale H-shape members built with SM490A (ordinary steel or benchmark material) and HSB800 (high-strength steel) were carried out. The primary objective was to investigate the appropriateness of extrapolating the local buckling criterion of the current codes, which was originally developed for normal-strength steel, to the case of high-strength steel. All the SM490A specimens performed consistently with the current code criteria and exhibited sufficient strength and ductility. The performance of the HSB800 specimens was also very satisfactory from the strength perspective; even the specimens with a noncompact and slender flange developed the plastic moment capacity. The HSB800 specimens, however, showed an inferior plastic rotation capacity due to the premature tensile fracture of the beam bottom flange beneath the vertical stiffener at the loading point. The plastic rotation capacity that was achieved was less than 3 (or the minimum level required for a plastic design). Although the test results in this study indicate that the extrapolation of the current flange local-buckling criterion to the case of high-strength steel is conservative from the elastic design perspective, further testing together with an associated analytical study is required to identify the causes of the tensile fracture and to establish a flange slenderness criterion that is more appropriate for high-strength steel.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.30-38
• /
• 2008

Petroleum-based resin adhesives have extensively been used for the production of wood panels. However, with the increase of manufacturing cost and the environmental issue, such as the emission of volatile organic compounds, of the adhesive resins, it is necessary to be developed new adhesive systems. In this study, the potential of okara, which is a residue wasted from the production of tofu, for the development of bio-based adhesives was investigated. At first, the physical and chemical properties of okara were examined. After okara was hydrolyzed in acidic and/or alkaline solutions, okara-based adhesive resins were formulated with the mixtures of the okara hydrolyzates and phenol formaldehyde (PF) prepolymer. The adhesive resins were used for the fabrication of plywood panels, and then the adhesive strength and formaldehyde emission of the plywood panels were measured to examine the applicability of the resin adhesives for the production of plywood panels. The solids content and pH of the okara used in this study were around 20% and weak acidic state, respectively. In the analysis of its chemical composition, the content of carbohydrate was the highest, and followed by protein. The shear strengths of plywood fabricated with okara-based resin adhesives exceeded a minimum requirement of KS standard for ordinary plywood, but its wood failure did not reach the minimum requirement. In addition, the formaldehyde emissions of all plywood panels were higher than that of E1 specified in the KS standard. Based on these results, okara has the potential to be used as a raw material of environmentally friendly adhesive resin systems for the production of wood panels, but further researches - biological hydrolysis of okara and various formulations of PF prepolymer - are required to improve the adhesive strength and formaldehyde emission of okara-based resin adhesives.

• Journal of Chest Surgery
• /
• v.42 no.6
• /
• pp.685-695
• /
• 2009

Background: Calcification is the most frequent cause of clinical failure of bioprosthetic tissues that are fabricated from Glutaraldehyde (GA)-fixed porcine valve or bovine pericardium. We recently used a multi-factorial approach of employing different mechanisms to investigate how to reduce the calcification of bioprosthetic tissues. The purpose of the present study was to evaluate the synchronized synergism using ethanol, L-lysine and $NaBH_4$ in glutaraldehyde treated porcine pericardium from the standpoint of calcification and tissue elasticity. Material and Method: Porcine pericardium was fixed with 0.625% GA (commercial fixation). An interim step of ethanol (80%; 1 day at room temperature) or L-lysine (0.1 M; 2 days at $37^{\circ}C$) or $NaBH_4$ (0.1 M; 2 days at room temperature) was followed by completion of the GA fixation (2 days at $4^{\circ}C$ and 7 days at room temperature). The tensile strength and thickness of the samples were measured. The treated pericardiums were implanted subcutaneously into three-week old Sprague-Dawley rats for 8 weeks. The calcium content was assessed by atomic absorption spectroscopy and the histology of the samples. Result: The amount of calcium in the pericardium pretreated with ethanol (13.6${\pm}$10.0 ug/mg, p=0.008), L-lysine (15.3${\pm}$1.0 ug/mg, p=0.002) and both (16.1${\pm}$11.1 ug/mg, p=0.012) was significantly reduced compared with the control (51.2${\pm}$8.5 ug/mg). However, $NaBH_4$ pretreatment (65.7${\pm}$61.8 ug/mg, p=0.653) and combined pretreatment that including ethanol, L-lysine and $NaBH_4$ (92.9${\pm}$58.3 ug/mg, p=0.288) were not significantly different from the controls(51.2${\pm}$8.5 ug/mg). Both the combined pretreatment using ethanol and L-lysine (7.60${\pm}$1.55, p=0.76) and the combined pretreatment that included ethanol, L-lysine and $NaBH_4$ (7.47${\pm}$1.85, p=0.33) increased the tensile strength/thickness ratio compared with that of the controls (4.75${\pm}$1.88). Conclusion: The combined pretreatment using ethanol and L-lysine seemed to decrease the calcification of porcine pericardium fixed with glutaraldehyde, as compared to single pretreatment, and it increase the tissue elasticity, but to the degree that showed synchronized synergism. $NaBH_4$ pretreatment seemed to increase the calcification of porcine pericardium, irrespective of whether single or combined pretreatment was used.