• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.2
• /
• pp.29-36
• /
• 2000

The principle and design of two-stage CMOS operational amplifier with rail-to-rail input and class-AB output stage is presented. The rail-to-rail input stage shows almost constant transconductance independent of the common mode input voltage range in global transistor operation region. This new technique does not make use of accurate current-voltage relationship of MOS transistors. Hence it was achieved by using simple linear relationship of currents. The simulated transconductance variation using SPICE is less the 4.3%. The proposed global two-stage opamp can operate both in strong inversion and in weak inversion. Class AB output stage proposed also has a full output voltage swing and a well-defined quiescent current that does not depend on power supply voltage. Since feedback class- AB control is used, it is expected that this output stage can be operating in extremely low voltage. The variation of DC-gain and unity-gain frequency is each 4.2% and 12%, respectively.

• Journal of IKEEE
• /
• v.15 no.3
• /
• pp.227-234
• /
• 2011

The Interest in robotics has been steadily increasing in recent times both in Korea as well as abroad. Research on robots for new and diverse fields is ongoing. This study discusses the current research and development on robot actuator, which are used to control the joints of robots, and focuses on developing more efficient technology for joint control, as compared with the current technologies. It also aims to find means to apply the abovementioned technology to diverse industrial fields. We found that easy and effective control of actuators could be achieved by using ZigBee sensor networks, which were widely being used on wireless communications. Throughout the experiments it is proved that the developed wireless actuator could be used for easy control of various robot joints. This technology can be effectively applied to develop two-legged robots that will be able to walk like human, or even quadruped and hexapod robots. It can also be applied to motors used in industry. In this study, we develop an extremely minimized ZigBee sensor network module that can be used to control various servo motors with low power consumption even if it is long distances. We realized effective wireless control by optimizing the ZigBee antenna, and were able to quickly check the status of relevant Tree node through mutual communication between the servo motors composing the ZigBee sensor network and the main server control modules. The developed Servo Motor with ZigBee sensor network modules can be applied in both robotics as well as for home or factory automation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.4 s.346
• /
• pp.56-65
• /
• 2006

The Quantum-dot Cellular Automata (QCA) can be considered as a candidate for the next generation digital logic implementation technology due to their small feature sizes and ultra low power consumption. Up to now, several designs using Uh technology have been proposed. However, we found not all of the designs function properly. Furthermore, no general design guidelines have been proposed so far. A straightforward extension of a simple functional design pattern may fail. This makes designing a large scale circuits using QCA technology an extremely time-consuming process. In this paper, we show several critical vulnerabilities related to unbalanced input paths to QCA gates and sneak noise paths in QCA interconnect structures. In order to make up the vulnerabilities, a disciplinary guideline will be proposed. Also, we present a fast adder which has been designed by the discipline, and verified to be functional by the simulation.

• Journal of Energy Engineering
• /
• v.16 no.3
• /
• pp.103-112
• /
• 2007

Flood issue for nuclear power plants designed and built in 1970 is extremely severe for main steam header compartment and main feedwater line region of intermediate building and lower floor. A calculation for flood level at the main feedwater line isolation compartment is now performing by hand calculation. But, this methodology is quite conservative assumption. The goal of this study was to develop method to analyze flowrate using the RETRAN-3D computer code, and the developed method was applied to flood level analysis following main feedwater line break. As a result of analysis, flood level was low remarkably.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.92-98
• /
• 1997

In this paper, the results of the measurement and analysis of extremely low freqency(ELF) eletric field in the vicinity of 154[kV] overhad transmission lines have been described. The planar-type electric field sensor has been fabricated by three dimensional structure with special consideration of taking the power frequency and lower components. The calibration experiments have been carried out according to the procedures of IEEE recommendation. The electric field measuring system has the frequency bandwidth of 7[Hz] to 2.7[MHz] and the response sensitivity of 0.094[mV/V/m]. Also the practical measurements of electric field under an 154[kV] double corcuit overhead transmission lines have been made abd abalyzed. It was known that the lateral electric field profiles under an 154[kV] double circuit overhead transmission lines show the asymmetrical distributions owing to the environmental metal frame structures and their maximum electric field magnitude is less than 3[kV/m]. It can be concluded that the measured results of the electric fields satisfy with all limits or guide -lines of the various authorized international institutes' recommendations.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.14-23
• /
• 1997

In this paper, the results of the measurement and analysis of extremely low frequency(ELF) electric field in the vicinity of 154[kV] overhead transmission lines have been described. The planar-type electric field sensor has been fabricated by three dimensional structure with special consideration of taking the power frequency and lower components. The calibration experiments have been carried out according to the procedures of IEEE recommendation. The electric field measuring system has the frequency bandwidth of 7[Hz] to 2.7[MHz] and the response sensitivity of 0.094[mV/V/m]. Also the practical measurements of electric field under an 154[kV] double circuit overhead transmission lines have been made and analyzed. It was known that the lateral electric field profiles under an 154[kV] double circuit overhead transmission lines show the asymmetrical distributions owing to the environmental metal frame structures and their maximum electric field magnitude is less than 3[kV/m]. It can be concluded that the measured results of the electric fields satisfy with all limits or guidelines of the various authorized international institutes' recommendations.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.513-516
• /
• 2013

In this paper, we present an information collecting system in medical information management domain. Our proposed system performs a systemized process, consisting of collection, transmission, and management, to develop intelligent medical information system and medical big data processing system. Our information collecting system consists of low-power biomedical sensors, biomedical information collecting devices, and storage systems. Currently, almost biomedical information of patients is collected manually by employees like nurses and medical doctors. Therefore, collected biometric data can be error-pronoun data. Since there is a lack to make big data of medical information, it is difficult to enhance the quality of medical services and researches. Accordingly, through our proposed system, we can overcome the problems like error-pronoun biometric data. In addition, we can extremely extend the area of collectable biometric data. Furthermore, using this system, we are able to make a real-time biomedical analysis system, like a real-time patient diagnosis system, and establish a strategy to against future medical markets changing rapidly.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.4
• /
• pp.87-91
• /
• 2010

Charged micro-particles are widely used as the key components for many electrical applications such as an e-paper, a touch panel, a printer toner and an electronic ink. Among them, the e-paper is an emerging reflective type display using the charged particles that has the advantages of the extremely low power consumption and sunlight readability. To create images on the e-paper, we confine black positively-charged and white negatively-charged particles between bottom and top electrodes and selectively apply the electric field. When the Coulomb force by an applied electric field is greater than the adhesion force between the charged particle and the electrode, the particles' transition happens resulting in the change of color between black and white. Therefore, the adhesion force is a very important factor for designing and estimating e-paper's operation. In this study, we constructed a basic model for particle's transition and an adhesion force equation describing particle's transition with three different forces: electrostatic image force, Van der Waals force and gravitational force. The simulation results showed that the gravitational force is negligible for the interesting range for the charge and the radius, and the adhesion force can be strongly dependent on the particle's charge and radius.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2498-2504
• /
• 2009

This paper compared the output limit value of the Korean weak electric field strength wireless device in the 8.2MHz band with the standard values of foreign countries. Through this, the study confirmed that the Korean regulation was lower by about 10-20dB than those of the USA or Europe. In order to prove this, the study measured outputs by entrusting the 8.2MHz EAS system to two measuring companies. As a result of these measurements, electric field strengths were shown to be $70.6dB{\mu}V/m$ and $68.3dB{\mu}V/m$ respectively, and these values were confirmed to exceed the current Korean standard of $59.8dB{\mu}V/m$. Accordingly, it is deemed necessary to review the specifications of the Korean standard in the 8.2MHz band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.395-400
• /
• 2017

The paper discussed the air-to-fuel ratio control of automotive fuel-injection systems using the cerebellar model articulation controller(CMAC) neural network. Because of the internal combustion engines and fuel-injection's dynamics is extremely nonlinear, it leads to the discontinuous of the fuel-injection and the traditional method of control based on table look up has the question of control accuracy low. The advantages about CMAC neural network are distributed storage information, parallel processing information, self-organizing and self-educated function. The unique structure of CMAC neural network and the processing method lets it have extensive application. In addition, by analyzing the output characteristics of oxygen sensor, calculating the rate of fuel-injection to maintain the air-to-fuel ratio. The CMAC may easily compensate for time delay. Experimental results proved that the way is more good than traditional for petrol control and the CMAC fuel-injection controller can keep ideal mixing ratio (A/F) for engine at any working conditions. The performance of power and economy is evidently improved.